topic Re: imx8ulp falcon image cannot burn in i.MX Processors

imx8ulp falcon image cannot burn

tangchao90 — Fri, 24 Jan 2025 07:29:38 GMT

my branch is scarthgap-6.6.36-2.1.0

https://github.com/nxp-imx/meta-imx/tree/scarthgap-6.6.36-2.1.0

https://github.com/nxp-imx-support/meta-imx-fastboot/tree/lf-6.6.36-2.1.0

my board is

https://www.nxp.com/design/design-center/development-boards-and-designs/MCIMX8ULP-EVK?tid=vanimx8ulpevk

According to the manual，MACHINE ??= 'imx8ulp-lpddr4-evk' but the image can't burn，below is the burn log. when i use branch imx_6.1.55_2.2.0, it can burn and start success，but i want to start quickly in falcon mode

U-Boot SPL 2024.04+gde16f4f1722+p0 (Sep 02 2024 - 10:44:35 +0000)
Normal Boot
ELE firmware version 1.2.0-4b189593
upower_apd_inst_isr: entry
upower_init: soc_id=48
upower_init: version:11.11.13
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.18
Turning on switches...
Turn on switches ok
Turning on memories...
Turn on memories ok
Clearing DDR retention...
Clear DDR retention ok
SEC0: RNG instantiated
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###

Re: imx8ulp falcon image cannot burn

Manuel_Salas — Fri, 24 Jan 2025 17:42:41 GMT

Hello @tangchao90

I hope you are doing well.

Could you please clarify if you are following the AN14093?

Are you using other method?

Please, if possible share steps to reproduce the issue.

Best regards,

Salas.

Re: imx8ulp falcon image cannot burn

elena_popa — Wed, 05 Feb 2025 09:15:42 GMT

Hi @tangchao90

Are you using UUU to flash the image? If so, please use the commands marked as a solutions in this ticket: https://community.nxp.com/t5/i-MX-Processors/How-to-load-Falcon-mode-image-to-emmc-on-imx8mplus-dev-board-nxp/m-p/2015307

Thanks,

Elena

Re: imx8ulp falcon image cannot burn

tangchao90 — Wed, 05 Feb 2025 01:50:43 GMT

yes, I use emmc flash and the command

.\uuu.exe -b emmc_all .\imx-boot-imx8ulp-lpddr4-evk-sd.bin-flash_singleboot_m33 .\imx-image-multimedia-imx8ulp-lpddr4-evk.rootfs-20250124060345.wic

uuu version is uuu (Universal Update Utility) for nxp imx chips -- libuuu_1.4.182-0-ga561ed7

Re: imx8ulp falcon image cannot burn

tangchao90 — Wed, 05 Feb 2025 01:58:54 GMT

my step is below:

1. repo init -u https://github.com/nxp-imx/imx-manifest.git -b imx-linux-scarthgap -m imx-6.6.36-2.1.0.xml

2. repo sync

3. enter the source directory and

git clone -b lf-6.6.36-2.1.0 https://github.com/nxp-imx-support/meta-imx-fastboot

4. DISTRO=fsl-imx-wayland MACHINE=imx8ulp-lpddr4-evk source imx-setup-release.sh -b build

5. cd build and

bitbake-layers add-layer ../sources/meta-imx-fastboot

6. bitbake imx-image-multimedia

after building , i can get image and burnin evk board

.\uuu.exe -b emmc_all .\imx-boot-imx8ulp-lpddr4-evk-sd.bin-flash_singleboot_m33 .\imx-image-multimedia-imx8ulp-lpddr4-evk.rootfs-20250124060345.wic

Re: imx8ulp falcon image cannot burn

elena_popa — Wed, 05 Feb 2025 09:14:37 GMT

Hi @tangchao90

The commands sequence should be:

.\uuu.exe -b emmc_all <default_bootloader> .\imx-image-multimedia-imx8ulp-lpddr4-evk.rootfs-20250124060345.wic .\uuu.exe -b emmc <default_bootloader> <falcon_mode_bootloader>

The first uuu command writes the wic image using the default bootloader.

The second uuu command writes the bootloader with falcon mode enabled (<falcon_mode_bootloader>) using the default bootloader.

For easiness, you can take the default bootloader from here: https://www.nxp.com/webapp/Download?colCode=L6.6.36_2.1.0_MX8ULP&appType=license

Thanks,

Elena

Re: imx8ulp falcon image cannot burn

tangchao90 — Fri, 07 Feb 2025 01:38:01 GMT

my steps is below

1. repo init -u https://github.com/nxp-imx/imx-manifest.git -b imx-linux-scarthgap -m imx-6.6.36-2.1.0.xml

2. repo sync

3. enter the source directory and

git clone -b lf-6.6.36-2.1.0 https://github.com/nxp-imx-support/meta-imx-fastboot

4. DISTRO=fsl-imx-wayland MACHINE=imx8ulpevk source imx-setup-release.sh -b build

5. cd build and

bitbake-layers add-layer ../sources/meta-imx-fastboot

6. bitbake imx-image-full

but my imx-boot-imx8ulpevk-sd.bin-flash_singleboot_m33 file size is 1224KB

i download from https://www.nxp.com/webapp/Download?colCode=L6.6.36_2.1.0_MX8ULP&appType=license imx-boot-imx8ulpevk-sd.bin-flash_singleboot_m33 file size is 1806KB

so my steps is not ok?

Re: imx8ulp falcon image cannot burn

tangchao90 — Fri, 07 Feb 2025 03:04:08 GMT

oh , i understand you! the <default_bootloader> is build without meta-imx-fastboot!

thank you

now my imx8ulp starts up with falcon image