i.MX Processors中的主题 Re: iM8MP MIPI-CSI Host error

iM8MP MIPI-CSI Host error

QiangF — Mon, 16 May 2022 08:52:45 GMT

Question Description：

With iM8MP, we try convert HDMI input image data translate to mipi-csi, The MIPI host reports Start of transmission error, [Lane3,Lane2,Lane1,Lane0]

the log as below：

the manual interrupt description

Hardware Environment：

The HDMI camera is connected to the imx8mp mipi csi2 interface through the HDMI TO CSI adapter board (LT6911C), as shown below

IMX8MP controls LT6911C chip through I2C2 bus

Software Environment：

1. Rootfs Ubuntu 20.04 rootfs, build from nxp yocto project
2. Kernel version 5.4.70, from Forlinx BSP
3. DTS LT6911UXC Node Configuration

&i2c2 {

clock-frequency = <100000>;

pinctrl-names = "default";

pinctrl-0 = <&pinctrl_i2c2>;

status = "okay";

lt6911uxc@2b {

compatible = "lontium,lt6911uxc";

reg = <0x2b>;

status = "okay";

// 省略部分无关信息

interrupt-parent = <&gpio5>;

interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;

reset-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;

plugin-det-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;

hpd-ctl-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;

camera-module-index = <0>;

port {

hdmi2csi_lt6911_in: endpoint {

data-lanes = <1 2 3 4>;

clock-lanes = <0>;

remote-endpoint = <&hdmi2csi_csi1_ep>;

link-frequencies = /bits/ 64 <297000000>;

};

&mipi_csi_1 {

#address-cells = <1>;

#size-cells = <0>;

status = "okay";

port@1 {

reg = <1>;

hdmi2csi_csi1_ep: endpoint {

remote-endpoint = <&hdmi2csi_lt6911_in>;

data-lanes = <4>;

csis-hs-settle = <13>;

csis-clk-settle = <2>;

csis-wclk;

};

}

Please tell me how to solve this problem

Re: iM8MP MIPI-CSI Host error

joanxie — Wed, 18 May 2022 13:05:36 GMT

could you share the logfile? what's your mipi csi input resolution and clock ?

Re: iM8MP MIPI-CSI Host error

QiangF — Wed, 18 May 2022 13:13:24 GMT

@joanxie

Thanks for your reply

Please read the attach Doc and log, Have description the question and kernel log

Waiting for your help!

Re: iM8MP MIPI-CSI Host error

joanxie — Sat, 21 May 2022 11:42:19 GMT

refer to your logfile, it seems this issue related to the clock issue, do you mind sharing the dts file? and try to use the command "v4l2-ctl --list-device" and "$ gst-launch-1.0 v4l2src device=/dev/video0 ! autovideosink"

Re: iM8MP MIPI-CSI Host error

QiangF — Tue, 24 May 2022 09:01:38 GMT

@joanxie

Now we determine the MIPI output clock and data is correct

but imx8 can not receive the lanes data，

Please review the attachment：DTS file

Re: iM8MP MIPI-CSI Host error

joanxie — Sun, 29 May 2022 07:29:22 GMT

SOT error means timing still isn't correct, so you still need to check the timings, the default dts file supports 4k already, maybe you can try that hssettle value, you can try different value, it seems that table isn't correct enough