topic Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board in i.MX Processors

Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Mon, 25 May 2020 08:03:41 GMT

Hi,

I'm using MfgTools in Windows 10.

The MfgTool_MultiPanel(Library: 2.7.0) was performed by executing the mfgtool2-yocto-mx-sabresd-sdcard-sd4.vbs of L4.9.88_2.0.0_mfg-tool.

LOG : MfgTool_Initial.log

The SD4 slot on the MCIMX6SX-SDB board has an SDCARD loaded with binaries built with the yocto project (imx-4.9.88-2.0.0_ga/imx-linux-rocko).

The boot mode switch has been changed to Serial Download mode.

(BOOT_MODE0[D1] : ON / BOOT_MODE1[D2] : OFF))

Then, when boot up the board, Windows 10 installs the (Freescale SE Blank PELE) driver, but the MFG Tools are forced to terminate.

LOG : MfgTool_Crash.log

Question. How can I download binaries to SDCard on the MCIMX6SX-SDB board using MfgTool?

Please answer.

Thanks.

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

joanxie — Tue, 02 Jun 2020 07:20:08 GMT

refer to the user guide, No dedicated boot DIP switches are reserved for serial download mode on i.MX 6 SABRE-SD and i.MX 6SoloLite boards, then when you connect your board with PC, check if you can find ""HID-compliant vendor-defined device" in the device manager, if you have issue for installing the driver, you need to check your PC, my win10 can install the driver successfully

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Mon, 08 Jun 2020 02:24:33 GMT

Hi, Joan Xie.

Thank you for your answer.

I did the following, but I have a problem.

1. mode change

2. Run the MFG_Tool

3. Power on the EVB board.

4. The MFG_Tool is terminated...

2~4. screen capture : http://shorturl.at/acmLP

(view in My Videos)

What are the differences causing this problem?

Please give me your opinion.
I appreciate it.

⨁ add contents : It works on other computers. it is the problem that only happens on my computer. In relation to that, is there anything wrong?

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

joanxie — Tue, 09 Jun 2020 06:33:34 GMT

you don't need to change the boot mode as your picture shows, my board's setting is 1=OFF, 2=ON

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Wed, 10 Jun 2020 01:37:48 GMT

Hi, Joan Xie.

I tested it under various conditions.

Computer	OS	Result
Desktop	Windows 10	problem occurrence
Notebook	Windows 7	normal operation
VMWare	Windows 10	problem occurrence
VMWare	Windows 7	normal operation
VMWare	Windows 8.1	problem occurrence

As shown in the table above, it seems to be the problem in Windows 10 & 8.1.

Windows 7 works fine.
Can you confirm the status quo?

Please give me your opinion.
I appreciate it.

⨁ add contents : There is also the forced shutdown problem in Linux.
The tested version is Ubuntu 12.04.3, 14.04.5, 16.04.6, 18.04 LTS.

Header 1
~/mfgtools$ sudo ./linux-runvbs.sh mfgtool2-yocto-mx-sabresd-sdcard-sd4.vbs Your Options: board: sabresd mmc: 3 sxuboot: sabresd sxdtb: sdb Ready to flash. Segmentation fault (core dumped) ~/mfgtools$

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

joanxie — Thu, 11 Jun 2020 09:21:41 GMT

my laptop is win10, everything is ok on my computer, did you check the driver installation successfully?

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Fri, 12 Jun 2020 00:32:27 GMT

Hi, Joan Xie.

Thank you for your reply.
If it works on your Windows 10, I guess my Windows 10 is the problem.

I couldn't check it on another Windows 10 computer because nothing.

Thanks.

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Tue, 16 Jun 2020 03:22:07 GMT

Hi, Joan Xie.

I got several windows 10 and tested them.

But it doesn't work.

Do you have a driver for Windows 10?

There is an event that failed migration in HID.

Please check again.

Thanks.

ps. The specification of my Windows 10 is "Windows 10 Pro / 1909 / 2020-02-24 / 18363.900"

⨁ add contents : The migration was resolved with the "sfc/scannow" command, but the MFGTool problem is not solved.

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

joanxie — Mon, 06 Jul 2020 08:47:15 GMT

sorry for missing your reply how about the status now? any improvement?

Re: Downloading binary to SDCARD(SD4 Slot) using MfgTool on the MCIMX6SX-SDB board

donghyunkim — Fri, 14 Aug 2020 00:12:50 GMT

Hi, Joan Xie.

MFGTools2 problem is not improved.

I think, it's a window 10 problem.

uuu is fine, so I'm using uuu instead of MFGTools2.

Thanks.