i.MX Processors中的主题 Re: IMX8MM - MIPI CSI

IMX8MM - MIPI CSI

santhosh2 — Fri, 31 Jul 2020 10:13:51 GMT

Hi,

The IMX8MM board configuration fsl-imx8mm-evk.dts file is configured to mipi ov5640 camera.

I am using high defination HDMI camera and using bridge IC converting from HDMI to MIPI data. The MIPI has three data lane and clock is generated from the source itself. so how to modify this for my application

(Camera and Bridge IC datasheet attached)

The current setting in fsl-imx8mm-evk.dts for mipi ov5640 camera are as below.

------------------------------------------------------------------------------------------------------------------------------------------------------

&mipi_csi_1 {
   #address-cells = <1>;
   #size-cells = <0>;
   status = "okay";
   port {
       mipi1_sensor_ep: endpoint1 {
           remote-endpoint = <&ov5640_mipi1_ep>;
           data-lanes = <2>;
           csis-hs-settle = <13>;
           csis-clk-settle = <2>;
           csis-wclk;
       };

       csi1_mipi_ep: endpoint2 {
           remote-endpoint = <&csi1_ep>;
       };
   };
};

    ov5640_mipi: ov5640_mipi@3c {
       compatible = "ovti,ov5640_mipi";
       reg = <0x3c>;
       status = "okay";
       pinctrl-names = "default";
       pinctrl-0 = <&pinctrl_csi_pwn>, <&pinctrl_csi_rst>;
       clocks = <&clk IMX8MM_CLK_CLKO1_DIV>;
       clock-names = "csi_mclk";
       assigned-clocks = <&clk IMX8MM_CLK_CLKO1_SRC>,
                  <&clk IMX8MM_CLK_CLKO1_DIV>;
       assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
       assigned-clock-rates = <0>, <24000000>;
       csi_id = <0>;
       pwn-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
       mclk = <24000000>;
       mclk_source = <0>;
       port {
           ov5640_mipi1_ep: endpoint {
               remote-endpoint = <&mipi1_sensor_ep>;
           };
       };
   };

Re: IMX8MM - MIPI CSI

igorpadykov — Sun, 02 Aug 2020 23:28:39 GMT

Hi Santhosh

for new camera driver adaptions one can look at below links

https://community.nxp.com/message/1342163?commentID=1342163#comment-1342163

https://community.nxp.com/message/1312444?commentID=1312444#comment-1312444

Best regards
igor
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: IMX8MM - MIPI CSI

santhosh2 — Fri, 07 Aug 2020 13:42:38 GMT

Thanks igor,

In the fsl-imx8mm-evk.dts is configured such that the processor generates the clock. But in our case Our Camera will be generating the clock signal. Do let me know what changes i need to do in the below configuration for setting the clock as external clock

Re: IMX8MM - MIPI CSI

Hrithik — Mon, 22 Aug 2022 07:08:30 GMT

Hi @santhosh2 ,

We are stuck in a similar situation as you had faced with another cam.
Could you please guide us the way you resolved this issue?

Thanks.

Re: IMX8MM - MIPI CSI

zohargolan — Thu, 25 Apr 2024 15:02:32 GMT

@santhosh2

Did you end up with a solution to this problem? did you manage to config the system to work with a device which is master on the MIPI clock?

I am trying to deal with the same problem now

Thank you,

Zohar