i.MX ProcessorsのトピックRe: i.mx6dl usb device disconnect from computer

i.mx6dl usb device disconnect from computer

zhongweihe — Thu, 07 Nov 2019 09:19:16 GMT

Our new project now customer feedback an issue is that usb device disconnect from computer sometimes but it can recover connect immediately.

MCU module: MCIMX6U5EVM10AC

Action:

1. USB eye diagram test is OK ,

2. if USB device connected to computer then remove the usb cable , but measured the USB_OTG_VBUS still output 4.4V(all of the products) .could you please help how to shut down the USB_OTG_VBUS?

Re: i.mx6dl usb device disconnect from computer

igorpadykov — Thu, 07 Nov 2019 23:49:42 GMT

Hi zhongwei

for usb disconnection problem one can check 24MHz clock stability

and try to use short quality shielded usb cable.

For "shut down the USB_OTG_VBUS" one can check USB_ID signal of

i.MX6 board, when removing the usb cable signal should be high or floating state.

Best regards
igor
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: i.mx6dl usb device disconnect from computer

zhongweihe — Fri, 08 Nov 2019 00:55:08 GMT

Hi Igorpadykov:

Thanks your quick respond .

1. Check 24MHz clock stability----OK , I will check with the crystal manufactor about it .

2. use short usb cable ------our end user's USB cable is about 3m length , but the usb eye diagram test is oK . so the hardware part is good I think .

3. USB_ID signal----how to check the USB_ID signal i can not find this signal . I measured the NXP demo board , if remove the usb cable from computor , the USB_OTG_VBUS is 0V but our is 4.4V .(the demo board MCU model is the same as our product)

Re: i.mx6dl usb device disconnect from computer

igorpadykov — Fri, 08 Nov 2019 05:08:49 GMT

Hi zhongwei

suggest to change custom board design according to i.MX6Q Sabre SD schematic.

USB_OTG_VBUS can be found on p.11 i.MX6Q Sabre SD schematic:

Design files, including hardware schematics, Gerbers, and OrCAD files for i.MX 6Quad (i.MX 6Dual emulation)

Best regards
igor

Re: i.mx6dl usb device disconnect from computer

zhongweihe — Mon, 11 Nov 2019 02:13:30 GMT

Hi igorpadykov,

Thanks your good support , up is our project about USB signal part .

1. Our USB not with OTG function ,

2. Signal USB_OTG_DN/USB_OTG_DP connect to USB type B connector directly as a device .

3. First time power up ; 1. if not connect USB cable to computer , the USB_OTG_VBUS =0V .

2. if connect USB cable to computer ,the USB_OTG_VBUS =5V , then if remove the

USB cable from computer ,the USB_OTG_VBUS=4.4V( Generallly , if remove the USB

USB cable from computer , the USB_OTG_VBUS should be 0V) so please help to check

why the USB_OTG_VBUS still output 4.4V if remove the USB cable from computer ?

Re: i.mx6dl usb device disconnect from computer

igorpadykov — Mon, 11 Nov 2019 04:03:47 GMT

Hi zhongwei

had custom board design followed i.MX6Q Sabre SD schematic.

If not, suggest to proceed with help of Commercial Support and Engineering Services | NXP

Best regards
igor

Re: i.mx6dl usb device disconnect from computer

zhongweihe — Tue, 12 Nov 2019 05:23:44 GMT

Hi Igor:

Today I mearsured the VDDUSB_CAP this voltage is 3.28V , but the specification of i.mx6dl show that this voltage is 3V , and I measured the Demo board is 2.98V . could you please help me to check how can I to regulate it ?

Re: i.mx6dl usb device disconnect from computer

igorpadykov — Tue, 12 Nov 2019 05:48:20 GMT

Zhongwei

suggest to recheck board schematic using IMX6DQ6SDLHDG, Hardware Development Guide for i.MX 6Quad, 6Dual, 6DualLite, 6Solo Families of Applications Processors

VDDUSB_CAP voltage can be regulated using PMU_REG_3P0n register described in

sect.51.7.2 Regulator 3P0 Register (PMU_REG_3P0n)

i.MX 6Solo/6DualLite Applications Processor Reference Manual

Best regards
igor

Re: i.mx6dl usb device disconnect from computer

zhongweihe — Tue, 12 Nov 2019 06:42:58 GMT

Hi Igor:

thanks your good support , i will try it .