i.MX Processors中的主题 Synaptics RMI4 Multitouch PAD

Connection

NOTE: nINT is an active-low open-drain pin for which the host must supply an external pull-up resistor.

DISP2_DAT9        --->  Touch_nINT DISPB2_SER_CLK    --->  Touch_I2C_DAT DISPB2_SER_DIO    --->  Touch_I2C_CLK EIM_A16           --->  Touch_nRST1

Touch PAD register.

Part of register map, that we need concern.

Addr	Name	Bit 7	Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1	Bit 0
0x0014	Interrupt status					Abs0	Button	Status	Flash
0x0015	Button data								Left

Addr	Name	Bit 7	Bit 6	Bit 5	Bit 4	Bit 3 - Bit 2	Bit 1 - Bit 0
0x0016	2D Finger State					Finger State 1	Finger State 0

Addr	Name	Bit 7 - Bit 0
0x0017	2D X position (11:4) Finger 0	X position [11:4]
0x0018	2D Y position (11:4) Finger 0	Y position [11:4]
0x001B	2D Z Finger 0	Z
0x001C	2D X position (11:4) Finger 1	X position [11:4]
0x001D	2D Y position (11:4) Finger 1	Y position [11:4]
0x0020	2D Z Finger 1	Z

Addr	Name	Bit 7 - Bit 4	Bit 3 - Bit 0
0x0019	2D Y/X position(3:0) Finger 0	Y Position [3:0]	X Position [3:0]
0x001A	2D Wy/Wx Finger 0	Wy	Wx
0x001E	2D Y/X position(3:0) Finger 1	Y Position [3:0]	X Position [3:0]
0x001F	2D Wy/Wx Finger 1	Wy	Wx

Get touch sample.

  I2CReadForTimes(0x2c,0x14,buf,0x11); // read out register value from register addr 0x14.   ts_sample->int_state = buf[0] & 0xF; // save interrupt status   ts_sample->button_data = buf[1] & 0x01; // save button_data      switch(buf[0x2] & 0xf) // 2D Finger State   {     case 0x0:  ts_sample->contact_resistance = 0;   break;     case 0x01:     case 0x02:  // bit0-1 is Finger 0 state       ts_sample->contact_resistance = 1;   ts_sample->x_position = (((buf[3]<<4))|(buf[5]&0xf));      ts_sample->y_position = (((buf[4])<<4)|((buf[5]&0xf0)>>4));  break;     case 0x04:     case 0x08: // bit2-3 is Finger 1 state        ts_sample->contact_resistance = 1;   ts_sample->x_position = (((buf[8]<<4))|(buf[10]&0xf));     ts_sample->y_position = (((buf[9])<<4)|((buf[10]&0xf0)>>4));         break;     case 0x05:     case 0x06:     case 0x09:     case 0x0a: // Finger 0 and Finger 1 press at same time      ts_sample->contact_resistance = 2;   ts_sample->x_position = (((buf[3]<<4))|(buf[5]&0xf));      ts_sample->y_position = (((buf[4])<<4)|((buf[5]&0xf0)>>4));          ts_sample->x2_position = (((buf[8]<<4))|(buf[10]&0xf));    ts_sample->y2_position = (((buf[9])<<4)|((buf[10]&0xf0)>>4));                break;      default :       printk("fail buf[0x16] = %d \n",buf[2]); // report real finger state value    return -1;   }

Transfer to screen pixel relate position. We use 480x800 for example

  if(ts_sample.int_state & 0x08) { // touch screen abs     if (ts_sample.contact_resistance < 2) {       if (ts_sample.x_position == 0 && ts_sample.y_position == 0 &&    ts_sample.contact_resistance == 0) {    x = last_x;     y = last_y;       }       else       {// transfer to screen relate position         x = ts_sample.x_position * 480 / 1894;          y = 799 - ts_sample.y_position * 800 / 3245;       }       if (x != last_x) {         input_report_abs(mxc_inputdev, ABS_X, x);       last_x = x;       }       if (y != last_y) {  input_report_abs(mxc_inputdev, ABS_Y, y);       last_y = y;       }       /* report pressure */       input_report_abs(mxc_inputdev, ABS_PRESSURE, ts_sample.contact_resistance);       /* report the BTN_TOUCH */       if (ts_sample.contact_resistance != last_press)       {      input_event(mxc_inputdev, EV_KEY,BTN_TOUCH, ts_sample.contact_resistance);       }     }     input_sync(mxc_inputdev);     last_press = ts_sample.contact_resistance;   }   else if(ts_sample.int_state & 0x04)  // button input   {     input_report_key(input_button,KEY_MENU,ts_sample.button_data);   }

i.MX Processors中的主题 Synaptics RMI4 Multitouch PAD

Synaptics RMI4 Multitouch PAD

Connection

Touch PAD register.

Get touch sample.

Transfer to screen pixel relate position. We use 480x800 for example

Re: Synaptics RMI4 Multitouch PAD