i.MX Processors中的主题 Re: Reboot imx6qp

Reboot imx6qp

corentinmorisse — Tue, 25 Jul 2017 09:32:57 GMT

Hi Community,

We have a custom board designed for a imx6DL using a design imx6qsabresd, booting from a eMMC v4.41, which is working fine.

We replaced the processor with a imx6 Quad Plus and use a eMMC v5.0 (MTFC16GAKAECN-4M)

We use Linux 4.1.15 and u-boot 2016.03-r0.

But now, the reboot hang.

The last message send by the board is « Rebooting... reboot: Restarting system ».

The board seem to reuse the DCD code loaded in the first boot (if we change the DCD code written in the eMMC after starting the board, when rebooting it will use the old one).

It hang immediately after, and the board go to serial downloader mode.

Using Boot_Tester.exe, it show that the imx seem to fail to access to the eMMC :

********************************************* 
Boot Debug (106.1) for MX6DQ or MX6DQplus
Build: Nov 10 2015, 21:43:53
Freescale Semiconductor, Inc. 
*********************************************
WDOG Fuse Disabled
Boot_cfg_1 = 0x70 
Boot_cfg_2 = 0xd0 
Boot_cfg_3 = 0x00 
Boot_cfg_4 = 0x4b
SBMR2        = 0x0a000001
 BMOD        = 10 Boot from GPIO/Fuses 
 BT_FUSE_SEL = 0 
 DIR_BT_DIS  = 0 
 SEC_CONFIG  = 01
Persistent Reg Value: 0x40000000
iROM Version = 0x20
USB_ANALOG_DIGPROG = 0x00630100 
 Device            = MX6 Dual/Quad Plus 
 Si Revision       = 2.0
Log Entry #0  (0x00010002) BOOTMODE - Internal/Override
Log Entry #1  (0x000200f0) Security Mode - Open 
Log Entry #2  (0x00030000) DIR_BT_DIS = 0 
Log Entry #3  (0x00040000) BT_FUSE_SEL = 0
Log Entry #4  (0x00050001) Secondary Image Selected
Log Entry #5  (0x00060001) USDHC Boot
Log Entry #6  (0x00070000) Device INIT Call
Log Entry #7  (0x000700f0) Device INIT Pass
Log Entry #8  (0x00080000) Device READ Data Call Address: 0x00000000 
Log Entry #10 (0x000800f0) Device READ Data Pass 
Log Entry #11 (0x00061004) Recovery Mode ECSPI 
Log Entry #12 (0x00080000) Device READ Data Call Address: 0x00000000 
Log Entry #14 (0x000800f0) Device READ Data Pass 
Log Entry #15 (0x00090000) HAB Authentication Status Code: 
              (0x000a0533) Invalid IVT 
Log Entry #17 (0x000c0000) Serial Downloader Entry 
Log Entry #18 (0x00090000) HAB Authentication Status Code: 
              (0x000a0533) Invalid IVT 
Log Entry #20 (0x000d0000) Serial Downloader Call 
              (0x0091712c) Address: 0x0091712c

We don’t use HAB, the board is in open mode.

Re: Reboot imx6qp

Rita_Wang — Wed, 09 Aug 2017 08:34:00 GMT

Hi,

When you change to the eMMC v5.0 you need to do some modify in souce code. You can refer to the thread

EMMC 5.0 and EMMC 5.1 work on i.MX6
Have a great day,
Rita

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: Reboot imx6qp

julienc — Tue, 29 Aug 2017 07:39:39 GMT

Hi Rita,

Thanks for your answer. I work with Corentin on the project but we use Linux 4.1.15 BSP release and the patch for support eMMC V5.0 and V5.1 is already applied.

We succeed to boot from eMMC but as i read in the thread " boot ROM will fall back to the eMMC4.4 standard when a eMMC4.5 or high version capable device is detected" , the reboot is not possible ?

As i am correct ? Any fix for detection possible ?

Thanks

Julien

Re: Reboot imx6qp

Rita_Wang — Tue, 29 Aug 2017 07:54:36 GMT

Hi Julien,

In our newest BSP, the driver support the emmc5.0 protocol and the performance is better than emmc4.41.The boot up is OK, the word you mentioned above mean that "The EMMC 4.5 or EMMC 5.0 /5.1 is backward-compatible with eMMC4.4". The emmc V5.0 and V5.1 can work on i.MX6. No problem.

Have a nice day

Rita

Re: Reboot imx6qp

julienc — Tue, 29 Aug 2017 09:38:34 GMT

I understand than i can boot from eMMC with ixm6 and eMMC V5.0 as eMMC V4.4 protocol but if we try to reboot with linux system the system still hang on the DCD code and not reload u-boot but with eMMC 4.4 the system reboot normally.

So i don't understand why it's only happening with eMMC V5.0.

Thanks for help.

Julien

Re: Reboot imx6qp

Rita_Wang — Fri, 01 Sep 2017 08:02:44 GMT

You need to check your hardware or software setting.

Re: Reboot imx6qp

corentinmorisse — Mon, 04 Sep 2017 15:07:30 GMT

For the hardware, the board work fine with a imx6DL and a eMMC v4.41, we replaced the processor with a imx6 Quad Plus and use a eMMC v5.0, so it seem that it’s not a hardware setting problem.

For the software, we use your driver, and the eMMC is configured to boot in x8ddr mode.

Thanks

Corentin