Digital Signal ControllersのトピックRe: Programming question on FRDM-56F83000

Programming question on FRDM-56F83000

DerekXiang — Wed, 08 Jul 2020 02:19:53 GMT

I create one project about FRDM-56F83000 (File-> New -> Project -> New Stationery Project, MC56F83789 -> MC56F83000-EVK -> C_Application), then compiling and programming are normal. But I added any code in main() function, the project could compile, and it could not program(the error windows appears). Why about this?

The attachment is the error information.

Re: Programming question on FRDM-56F83000

xiangjun_rong — Wed, 08 Jul 2020 05:43:37 GMT

Hi, Derek,

I have to make sure that the hardware connection is okay.

If you use on-board OSJTAG, you have to close J11 and inset USB cable to J8.

If you use Multilink Universal device, pls select Open J11 on the FRDM board, and select the ********U-Multilink as following Fig

Note that the USBTAP device is NOT supported for MC56F83xxx family.

Hope it can help you

Xiangjun Rong

Re: Programming question on FRDM-56F83000

DerekXiang — Wed, 08 Jul 2020 07:46:47 GMT

Hi, Xiangjun,

I make sure that the hardware connection is okay. I can program the other example code which was created by the other method.

You need create the project by "New Stationery Project", then you could repeat this question.

The following is the related picture.

Re: Programming question on FRDM-56F83000

xiangjun_rong — Wed, 08 Jul 2020 09:19:23 GMT

Hi, Derek,

Regarding the project created with the procedure File-> New -> Project -> New Stationery Project, MC56F83789 -> MC56F83000-EVK -> C_Application, this is a template based on Quick_Start tools, if you use the project, you have to install the quick_start tools.

Pls refer to the attached doc for installing the quick_start tools.

Hope it can help you

XiangJun Rong

Re: Programming question on FRDM-56F83000

DerekXiang — Thu, 09 Jul 2020 01:26:13 GMT

HI, Xiangjun,

I have already installed the quick_start tools according to this PDF document.

Re: Programming question on FRDM-56F83000

DerekXiang — Thu, 09 Jul 2020 01:48:27 GMT

Hi, XiangJun,

The attachment is the problematic project.

Please check whether it could download on your 56F83000_EVK hardware.

Re: Programming question on FRDM-56F83000

xiangjun_rong — Fri, 10 Jul 2020 02:20:58 GMT

Hi, Derek,

After you download quick_start tools and recompile, can you download code to flash now?

XiangJun Rong

Re: Programming question on FRDM-56F83000

DerekXiang — Fri, 10 Jul 2020 08:50:56 GMT

Hi, XiangJun,

After I recompiled the project, I could not download code to flash. In the previous email, I have added the problematic project.

Re: Programming question on FRDM-56F83000

xiangjun_rong — Mon, 13 Jul 2020 06:03:59 GMT

Hi, Derek Xiang,

After I modified your code, I can debug your code as the screenshot.

As I said, if you create a project based on Quick Start tools, you have to load the GCT and setting the GCT correctly.

Enable GPIOF gated clock in GCT tools

//set up GPIOF8 pin as output

//add the code in while(1):

ioctlGPIO_SET_PIN(GPIO_F,BIT_8);
ioctlGPIO_CLEAR_PIN(GPIO_F,BIT_8);

Re: Programming question on FRDM-56F83000

DerekXiang — Mon, 13 Jul 2020 07:57:11 GMT

Hi, XiangJun,

Thanks you for your reply.

According to your means, I could program the code.

Do you have other document about the GCT using (except the DSC56800EX Quick Start User’s
Guide)?

Re: Programming question on FRDM-56F83000

xiangjun_rong — Tue, 14 Jul 2020 02:19:51 GMT

Hi,Derek,

Unfortunately, I have not the other documentation about the quick-start tools, the DSC56800EX Quick Start User’s
Guide is the only one I have.

XiangJun Rong

Re: Programming question on FRDM-56F83000

DerekXiang — Tue, 14 Jul 2020 06:00:07 GMT

Hi, XiangJun,

Thanks! I can only try to use this software tool by myself.

Re: Programming question on FRDM-56F83000

haroldhulbert91 — Tue, 14 Jul 2020 06:12:51 GMT

Did you get the solution? If yes then please share with me, I am a beginner in programming and I face the same issue, in fact your error file help me alot.