CodeWarrior for MCU中的主题 Re: LINK in .prm. https://community.nxp.com/t5/CodeWarrior-for-MCU/LINK-in-prm/m-p/140952#M2593 <HTML><HEAD></HEAD><BODY><DIV>Hello</DIV><DIV>&nbsp;&nbsp; Are you building from the IDE?</DIV><DIV>&nbsp;&nbsp; In this case the name of the generated executabel file is defined in the target settings Linker panel. The file name specified there has higher priority than the name specified in the .prm file.</DIV><DIV>&nbsp;</DIV><DIV>&nbsp; To modify it:</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Open your project</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Open the target setting dialog (press ALT+F7)</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Switch to the "Linker for HC08" or "Linke for HC12" Panel (depending on the CPU you are targeting)</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;- Change the application file name.</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Click OK to close the dialog</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Rebuild your project.</DIV><DIV>&nbsp;</DIV><DIV>I hope this helps.</DIV><DIV>&nbsp;</DIV><DIV>CrasyCat</DIV></BODY></HTML> Fri, 22 Dec 2006 15:42:21 GMT CrasyCat 2006-12-22T15:42:21Z LINK in .prm. https://community.nxp.com/t5/CodeWarrior-for-MCU/LINK-in-prm/m-p/140951#M2592 <HTML><HEAD></HEAD><BODY><DIV>I want to specify name of output&nbsp; file be used to "LINK". linker successful ,but didn't generate the file.</DIV><DIV>How I can?</DIV></BODY></HTML> Fri, 22 Dec 2006 10:55:25 GMT https://community.nxp.com/t5/CodeWarrior-for-MCU/LINK-in-prm/m-p/140951#M2592 bennyxu 2006-12-22T10:55:25Z Re: LINK in .prm. https://community.nxp.com/t5/CodeWarrior-for-MCU/LINK-in-prm/m-p/140952#M2593 <HTML><HEAD></HEAD><BODY><DIV>Hello</DIV><DIV>&nbsp;&nbsp; Are you building from the IDE?</DIV><DIV>&nbsp;&nbsp; In this case the name of the generated executabel file is defined in the target settings Linker panel. The file name specified there has higher priority than the name specified in the .prm file.</DIV><DIV>&nbsp;</DIV><DIV>&nbsp; To modify it:</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Open your project</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Open the target setting dialog (press ALT+F7)</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Switch to the "Linker for HC08" or "Linke for HC12" Panel (depending on the CPU you are targeting)</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;- Change the application file name.</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Click OK to close the dialog</DIV><DIV>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; - Rebuild your project.</DIV><DIV>&nbsp;</DIV><DIV>I hope this helps.</DIV><DIV>&nbsp;</DIV><DIV>CrasyCat</DIV></BODY></HTML> Fri, 22 Dec 2006 15:42:21 GMT https://community.nxp.com/t5/CodeWarrior-for-MCU/LINK-in-prm/m-p/140952#M2593 CrasyCat 2006-12-22T15:42:21Z