topic Re: Debugging attempt: Error in services launch sequence in CodeWarrior for MCU

Debugging attempt: Error in services launch sequence

莱昂纳多迪卡普里奥 — Tue, 27 Oct 2015 09:24:25 GMT

Hi guys.

I am trying to debug a KSDK example application on FRDM-KL02Z, but after building the project,the problem occured,just like this window:

please someone help me to figure this problem,Im a new man.

Thanks.

Re: Debugging attempt: Error in services launch sequence

trytohelp — Tue, 27 Oct 2015 10:31:51 GMT

Hi,

Some questions:

What is the OS used ?

What is the KDS and KSDK version used ?

To check your hardware configuration I recommend you to create an example with the Project Wizard without KSDK and PEx.

Can you try this sample example ?

Have a great day,
Pascal
Freescale Technical Support
-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: Debugging attempt: Error in services launch sequence

ivadorazinova — Tue, 27 Oct 2015 11:21:23 GMT

Hi,

Please, follow these steps mentioned hereGDB Debugging with Kinetis Design Studio

Let us know, if it helps you.

Best Regards,

Iva

Re: Debugging attempt: Error in services launch sequence

莱昂纳多迪卡普里奥 — Wed, 28 Oct 2015 14:45:48 GMT

hey Iva,

thanks for your help,but it didn't work.

I remember that I met another situation when I was installing KSDK 1.3.0 Eclipse Update.

I choosed OK button and continue to install it. Then debugging attempt failed, it may caused by this warning (I guess!)

In fact ,I still can't figure it out. I mean,I did every single step according to

FRDM-KL02Z: Freescale Freedom Development Platform for the Kinetis KL02 Family/Get Started

on freescale website.

god ,just help me!

Thanks,

leon.

Re: Debugging attempt: Error in services launch sequence

莱昂纳多迪卡普里奥 — Wed, 28 Oct 2015 14:52:33 GMT

hey Pascal,

my PC‘s OS is windows8 and KSDK version is 1.3.0 and KDS version is 3.0.0

Im sure there is no problem with version,cause I did every step from

FRDM-KL02Z: Freescale Freedom Development Platform for the Kinetis KL02 Family/Get Started

on freescale website.

thanks for your help,but it didn't work.

I remember that I met another situation when I was installing KSDK 1.3.0 Eclipse Update.

I choosed OK button and continue to install it. Then debugging attempt failed, it may caused by this warning (I guess!)

In fact ,I still can't figure it out.

god ,just help me!

Thanks,

Pascal

Re: Debugging attempt: Error in services launch sequence

trytohelp — Wed, 28 Oct 2015 15:28:23 GMT

Hi,

don't know if this can help but ...

Can you just check if a very sample project created with the wizard ?

Just an example without KSDK or PEx to check if there is a problem with KDS and the board.

What is the connection type you're using ?

Re: Debugging attempt: Error in services launch sequence

trytohelp — Thu, 29 Oct 2015 09:49:25 GMT

Hi,

This morning I've installed KDSV3.0.0 on Win 8.1 64 bit OS.

Only KDS was installed for this test.

My config is:

Win 7 64 bit

VirtualBox + Win 8.1 64 bit

KDS v3.0.0

FRDM-K64F

Based on this configuration, after to have connected the Device to Win 8.1 64bit, I've created an example using KDS V3.0.0 only for this board.

After to build the project I launch the debug session selecting the Debug_PNE.

Now the application is loaded fine on my board.

Re: Debugging attempt: Error in services launch sequence

Carlos_Mendoza — Thu, 29 Oct 2015 16:59:53 GMT

Hi 莱昂纳多迪卡普里奥,

Have you tried reinstalling the P&E drivers?

Go to the folder C:\Freescale\KDS_3.0.0\pemicro and there you will find the P&E drivers installer:

Hope it helps!

Best Regards,

Carlos Mendoza

Technical Support Engineer

Re: Debugging attempt: Error in services launch sequence

莱昂纳多迪卡普里奥 — Sun, 01 Nov 2015 11:47:44 GMT

Hi Pascal,

Im a newbie,and I dont know how to check if a very sample project created with the wizard.

Could you give me some specific steps?

Thank you very much!

Leon

Re: Debugging attempt: Error in services launch sequence

莱昂纳多迪卡普里奥 — Sun, 01 Nov 2015 11:54:05 GMT

Hi Carlos,

I reinstalled the P&E drivers and it did helpful,

then another problem occurred at 95% launching the debug session,here is screenchop:

sorry to trouble you again,

I just dont know how to deal with it.

Thanks,

Leon

Re: Debugging attempt: Error in services launch sequence

trytohelp — Fri, 06 Nov 2015 16:06:12 GMT

Leon,

Sorry for the delay.

Attached a video showing you how to create a sample example.

Re: Debugging attempt: Error in services launch sequence

matijavarga — Sat, 23 Jan 2016 12:45:02 GMT

Dear all,

I have the exactly same problem, exactly the same board and have tried exactly the same example..

It is extremely frustrating that there is so few error details and still no solution!

Operating System:

Win 8.1 Pro

Kinetis SDK 1.3.0

KDS 3.0.0.

Tried reinstalling PE driver, can see it in Device Manager, cannot see it in the Debug Configuration (see pictures). Tried to run dummy sample that was suggested above.. No results, same error.

Debug Configurations:.

PE HW info

Please help..

Matija.

Re: Debugging attempt: Error in services launch sequence

BlackNight — Sun, 24 Jan 2016 19:00:14 GMT

Hello,

if there is nothing listed in the 'Port' settings, that means no debug drivers are found or present.

About drivers: see here: Fixing the USB Drivers | MCU on Eclipse

From your PE hardware information, it seem that you have not loaded the debug OpenSDA firmware on the board?

Are you sure you have loaded the correct debug firmware? Note that if you have received a board from the factory, then you need a Windows 7 machine to update the bootloader and to load the debug firmware (you cannot do this with a Windows 8 machine).

See here for instructions (again, you need a Windows 7 machine):

Illustrated Step-by-Step Instructions: Updating the Freescale Freedom Board Firmware | MCU on Eclipse

I hope this helps,

Erich