topic Re: vitess binary file base address in cw 10.3.3 in CodeWarrior Development Tools

vitess binary file base address in cw 10.3.3

Nuevo — Wed, 18 Dec 2013 06:27:29 GMT

Hi

Could u please tell about vitess binary file memory location for cw,,, during nor flash programming,,,,, what will be the starting and ending address and address offset for vsc2bin file...................

Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 07:26:23 GMT

Vitess firmware should be programmed at the beginning of NOR flash.

What board you are using? In this link you can find an example for P2020RDB-PC board. Start address for vitess firmware in u-boot is 0xEF00_0000, and also in CW will be 0xFF00_0000.

Adrian

Re: vitess binary file base address in cw 10.3.3

Nuevo — Wed, 18 Dec 2013 08:38:52 GMT

Adrian

p1020rdb-pc

https://community.freescale.com/thread/309502 in this link u have told that base address is FF710000......... then which one will be the correct base address and offset addresss

Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 08:51:39 GMT

Exemple for p2020rdb-pc

If you are trying to program vitess firmware using CW Flash Programmer, you should set the offset at address: 0xFF00_0000. To check vitess firmware is in NOR, open Memory view and add 0xFF000000 to monitor.

After that, you can go to u-boot, and check vitess firmware at address 0xEF000000 (md.b ef000000 10). Also, according with this link, you should set vscfw_addr env variable.

Adrian

Re: vitess binary file base address in cw 10.3.3

Nuevo — Wed, 18 Dec 2013 09:56:38 GMT

Adrian

Sorry for disturbing u again

Our Board is P1020RDB-PC and SDK is V1.01 for this Board could u please tell what will be the base address for vitess firmware and offset address

regards

chaya

Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 10:07:00 GMT

Is the same offset.

Adrian

Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 10:52:40 GMT

You mean, u-boot is not booting (nothing on terminal)?

Adrian

Re: vitess binary file base address in cw 10.3.3

Nuevo — Wed, 18 Dec 2013 11:03:51 GMT

yes Junk data is coming not getting the boot logs, from memory view can view the logs, but in terminal i am unable to view the logs

Re: Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 12:17:29 GMT

Please check the following:

- u-boot is programmed using CW starting with address 0xFFF80000

- switch settings: SW2: OFF ON ON ON ON ON ON ON and SW3: ON ON OFF ON OFF ON ON OFF

- serial cable adapter should be connected in UART0 and set baud rate to 115200. Serial cable should be null modem

- attached is the u-boot i used on my board

I have tested on a board similar with the one you own and with the setup above works fine. If your board is set as above and the u-boot is not booting, it looks like your board have a hardware issue.

Adrian

Re: vitess binary file base address in cw 10.3.3

Nuevo — Wed, 18 Dec 2013 12:36:40 GMT

What u sent the logs,, same logs am getting in the memory view,,,,,,,,,,,,, but board is not booting up,,,

Re: vitess binary file base address in cw 10.3.3

addiyi — Wed, 18 Dec 2013 12:50:39 GMT

I suggest you summit a service request to Freescale warranty team, using www.freescale.com (Support -> Technical Service Request), because probably is a hardware issue.

Adrian