Classic/Legacy CodeWarriorのトピックRe: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

antony_GB — Tue, 01 Feb 2011 21:26:32 GMT

Hi there.

My problem here is that I am using the codewarrior device initialization bean to set up the ADC. I have not yet experienced any problems when using the 'Device Initialization' tool when using it to setup pins for GPIO. I have included below the exact bean parameters, and the code to write a '1' to the START0 bit of register CNTRL1. Can anyone advise on why a scan will not run?

-Setting

Clock Settings

Clock Divisor select divide by 8

ADC Freq 5MHz

Stop mode 0 no

Stop mode 1 no

ADC mode Once sequential

Parrallel mode Independent

Trigger mode 0 Write to START bit only

Trigger mode 1 " "

High voltage ref source External (AN2 connected to VDDA)

Low voltage ref source External (AN6 connected to GND)

-A/D channels

AN0-AN1 Single ended mode

AN2-AN3 " "

AN4-AN5 " "

AN6-AN7 " "

-sample 0

channel AN0

sample Enabled

zero crossing Disabled

low limit 0

high limit 32752 (highest value before disabling high limit)

-sample 1- 7 All disabled

-pins

-AN0 Enabled

-AN2/Vrefh pin Enabled

-AN6/Vrefl pin Enabled

the rest of the pins are disabled

Sync0 and sync1 are both disabled

-interrupts

-conversion complete

interrupt INT_ADC_ADCA

request Enabled

level 7

Priority Highest

End of scan interrupt Enabled

conversion complete interrupt for scanner b is disabled

Zero crossing or limit error

interrupt INT_ADC_ADCINT

Request Enabled

Level 7

Priority 6

Zero crossing Disabled

Low limit error Disabled

High limit error Enabled

-Initialization

Start ADC conversion after Init A no

" " B no

Power down ADC0 no

" " 1 no

Power down voltage ref no

Auto power down disabled

power up delay 13

Auto stand by disabled

The following code is used to start the scan.

#include "support_common.h"

uint16 Set_START0 = 0;

set_START0 = CNTRL1;

Set_START0 = (uint16)(Set_START0 | CTRL1_START0_BITMASK);

CTRL1 = SetSTART0;

The code compiles, but as far as i can tell, there is no scan being run, and at no point during debug will the program jump to the corresponding end of scan ISR.

Apologies if I have gone a bit over kill on the information included here, I just didn't want to miss out anything that might be important. If anyone has any suggestions, I would be most greatfull. Thanks in advance. Antony

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

ProcessorExpert — Thu, 03 Feb 2011 17:27:07 GMT

Hello,

could you please post here a simple project showing the issue? Are you using some specific EVB board?

best regards
Vojtech Filip
Processor Expert Support Team

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

antony_GB — Thu, 03 Feb 2011 20:30:24 GMT

Hi Processor expert, I have attached a simple project, although this is not a version of the program i have actually been working on, i knocked this one up quickly to demonstarte how my actual program initializes the ADC scan, and how i want it to use the end of scan interrupt. I do experience the same problem with this program as i do my actual program. All timers and clocks have been set the same.

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

antony_GB — Thu, 03 Feb 2011 20:32:26 GMT

Just one quick thing, I have changed the interrupt levels, and priorities from those specified in the origonal post.

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

ProcessorExpert — Fri, 04 Feb 2011 18:11:46 GMT

Hello,

I have reproduced the problem.It’s not a problem in generated code but there is missing clearing sequence in handling of PIT interrupt . There is also set the priority of ADC interrupt to lower value than PIT. Due to missing the clearing sequence PIT hangs in handling of the isr – and it cannot be interrupted by ADC because the interrupt has lower priority and it never occurs.

I have corrected your project, please find it enclosed.

best regards
Vojtech Filip
Processor Expert Support Team

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

antony_GB — Mon, 07 Feb 2011 20:07:06 GMT

Thank you for your response ProcessorExpert. I loaded the program you returned. I am still experiencing problems with the handling of interrupts. I cleared the PIF bit where you stated to do so, I then found that my program did generate an interrupt from the ADC, but then the program continued to jump immediately back to the ADC end of scan interrupt. I assumed that this must be due to a similar reason as before, so i cleared the EOSIE0 (interrupt enable) bit at the beginning of the interrupt, and set it again before writing to START0. This did seem to stop the re-calling of the ADC end of scan interrupt, however, since clearing the PIF bit, no further PIT0 timeout interrupts are occuring. I have tried setting the OVW bit, i thought this might jog the PIT back into action, but still there appears to be no activity. Can you advise? Thanks again. Antony

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

ProcessorExpert — Mon, 07 Feb 2011 22:35:47 GMT

Hello,

I think that the problem is in the ADC´s ISR where there is a neverending loop that causes your program hanging in the isr - see below.

    for(;
   {
       ++count;//this is where i expect my program to end up
   }

Corrected project is enclosed.

best regards
Vojtech Filip
Processor Expert Support Team

Re: Initializing an ADC scan, MCF5213, Codewarrior V5.9.0

antony_GB — Tue, 08 Feb 2011 01:01:50 GMT

Amazing, problem solved, and solved. Its so simple, I've just deleted half my code. Thanks alot for the help. Antony