topic Re: 88W9098(WLAN:SDIO) loading driver with mmc error message in Wi-Fi® + Bluetooth® + 802.15.4

88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Wed, 17 Jan 2024 17:21:48 GMT

Hi Support,

We encountered an issue while testing 88W9098(WLAN:SDIO) on openwrt 22.03.3 with kernel 5.10.161.

While loading driver, the mmc error message appeared and there's no wireless interface at all.

Using below commands to load driver.
# insmod mlan.ko
# insmod moal.ko drv_mode=7 cal_data_cfg=none fw_name=nxp/sdiouart9098_combo_v1.bin

Could you please help guide how to load driver with correct commands and suitable parameters?

What could be the reason for showing mmc related error message?

Please advise.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Fri, 07 Apr 2023 08:30:00 GMT

Dear Andy,

Could you please clarify your setup ?

- host used

- 88W9098 module used

- how you connect 88W9098 to your host

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Mon, 10 Apr 2023 08:02:58 GMT

Hi Olivier,

1. host : Microchip sama5d35
2. AZW-XM458
3. 88W9098 is LGA type

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Tue, 11 Apr 2023 09:05:22 GMT

Dear @Andy_Hsieh

Could you please:

1/ confirm you are using AW-XM458MA-SUR (and not AW-XM458MA-PUR) ?

2/ confirm the host OS (openWRT) and OS version

3/ explain how you connect the AW-XM458MA to your host ? (picture might help)

4/ provide wifi driver and FW version

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Tue, 11 Apr 2023 09:22:52 GMT

Hi Olivier,

1. Actuaclly, we used AW-XM458MA LGA type and modified WLAN interface to SDIO with following instructions shared from Azurewave's datasheet.

2. OS is Openwrt 22.03.3 with kernel 5.10.161.

3. Sorry, I don't have the device now so can't provide a photo for your reference.

4. Driver package as attachment.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Tue, 11 Apr 2023 13:02:18 GMT

Dear @Andy_Hsieh

You first need to make sure that SDIO is correctly detected by the Linux kernel:

$ dmesg | grep mmc

Shoud return 'mmcX: new high speed SDIO card at address 0001' message

If you do not get that message, it is useless to load the Wifi driver.

In that case, you need to check that SDIO is correctly configured in the device tree.

Do you have SDIO correclty detected ?

Regards,

Olivier

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Wed, 12 Apr 2023 01:01:42 GMT

Hi Olivier,

Please refer to below screenshot, it seems that SDIO is correctly detected by system.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Wed, 12 Apr 2023 07:45:20 GMT

Dear @Andy_Hsieh

Could you please check if SDIO IO level is the same on both host and AW-XM458 module side ? (basically, both should be 1.8V)

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Wed, 12 Apr 2023 08:38:27 GMT

Hi Olivier,

For both sides, they're with 3.3V.

According to datasheet, it should be working, right?

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Wed, 12 Apr 2023 08:44:32 GMT

Dear @Andy_Hsieh

Then we should add no-1-8-v; to usdhc node in dts.

If the same error occurs, please provide the schematics so we can crosscheck your design.

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Wed, 12 Apr 2023 08:47:55 GMT

Hi Olivier,

Regarding your response "Then we should add no-1-8-v; to usdhc node in dts.", could you please explain more details so that I could understand your suggestion and know how to do.

Thank you in advance.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Wed, 12 Apr 2023 14:21:34 GMT

Dear @Andy_Hsieh

no-1-8-v option should be added to your Linux kernel device tree (usdhc node).

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Thu, 13 Apr 2023 01:46:04 GMT

Hi Olivier,

Result is still the same after adding no-1-8-v to device tree. Here's our device tree configuration for your reference.

Is there any other possibility which may cause such issue?

Please advise.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

ocourson — Thu, 13 Apr 2023 07:23:39 GMT

Dear @Andy_Hsieh

I just sent you a private message, as we need you to share private information to continue investigations.

Regards,

Olivier

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Thu, 13 Apr 2023 09:05:11 GMT

Hi Olivier,

I don't receive your private message. Please check once.

Thanks.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

weidong_sun — Tue, 18 Apr 2023 08:45:51 GMT

Hello @Andy_Hsieh ,

I checked your schematic of M.2 card. you are using AW-XM458 LGA module, and VIO_SD is 3.3V. then I also found CPU uSDHC IO level is 3.3V.

1. Your design is non-standard M.2 card

According to M.2 Spec, SDIO signals should be 1.8V IO.

But for your design, the card can also work. because both sides lO level are matched (both 3.3V)

2. Just comfirming some points with you

(1) PIN 23 on M.2

it should be pulled up high in your dts. or populate R8.

(2) GPIO[16] & GPIO[15]

GPIO16 & GPIO15 are used to select work clock, if GPIO16 =1 & GPIO15=1, 40MHz clock will be used.

About these pins' status, you should confirm them with AW Engineer, To confirm if floating them is OK.

(3) About your logs

According to your logs, I didn't see logs related to loading firmware. Could you confirm if the firmware ,sdiouart9098_combo_v1.bin has been placed to /lib/firmware/nxp directory.

After checking or correcting above items, use the following commands, please!

# insmod mlan.ko

# insmod moal.ko 'cfg80211_wext=0xf max_vir_bss=1 drv_mode=7 ps_mode=2 auto_ds=2 fw_name=nxp/sduart9098_combo_v1.bin cal_data_cfg=none host_mlme=1'

[Note]

SD9098 driver, it 's firmware name is 'sduart9098_combo_v1.bin', BUT yours is sdiouart9098_combo_v1.bin , did you rename it?

Try it , please!

Regards,

weidong

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Tue, 18 Apr 2023 14:09:12 GMT

Hi Weidong,

Thank you for your information.

Regarding your suggestion for PIN 23 on M.2, does it mean that we must have to pull up high?

Regarding your suggestion for GPIO[15] & [16], could you please explain more in details?

Should we modify the current design for GPIO[15] & [16]?

Actually, according to the driver source package I have, FW file name is "sdiouart9098_combo_v1.bin" as below screenshot.

BTW, may I know whether it could be a driver issue?

Do you have any other version of driver that I can test?

Thanks.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

weidong_sun — Wed, 19 Apr 2023 11:28:45 GMT

Hello @Andy_Hsieh ,

>>Regarding your suggestion for PIN 23 on M.2, does it mean that we must have to pull up high?

Yes, it should be pulled up to HIGH.

Do it on hardware or software , either of them is OK.

>>Regarding your suggestion for GPIO[15] & [16], could you please explain more in details?

GPIO[15] & [16]=11, means that 9098 will use 40MHz clock. default settings for these 2 pins, one is PD(pull down), the other is PU, so default is GPIO[16:15]=01. SO you should confirm it with AW engineer , to check if GPIO16 is pulled up in 458 LGA module. if yes, it means the current level of GPIO[16:15]=11, so don't need to do anything for these 2 pins, floating them is no problem.

>>may I know whether it could be a driver issue?

No, we can't say that. Because there are no firmware messages in your logs, we are not sure if firmware has been loaded correctly. SO confirm if firmware is at the path /lib/firmware/nxp, which is very important step.

>>Do you have any other version of driver that I can test?

We are not authorized to share driver source code to customers. if customer has NDA & access rights , she can download wifi materials from nxp website.

additonally, your current driver should be no problem for your platform.

Try it, please!

then tell me result, please!

Regards,

weidong

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

Andy_Hsieh — Wed, 03 May 2023 06:38:17 GMT

Hi weidong,

Test result is still the same with your previous suggestions.

Please find following screenshot and attached dmesg log for reference.

Could you please advise about this wlan_sdio mmc error issue?

Is there any other information you need to have further analysis?

Thank you in advance.

Re: 88W9098(WLAN:SDIO) loading driver with mmc error message

weidong_sun — Thu, 04 May 2023 09:14:17 GMT

Hello @Andy_Hsieh ,

Here is my personal email address: weidong.sun@nxp.com

please send your full schematic of platform & full schematic of wifi card to me!

the current issues you encounterred is a typical error on MMC communications. so let me see your hardware design again.

Thanks!

Regards,

weidong