S32KのトピックRe: S32K311 FLASH ready for program after functional software reset

S32K311 FLASH ready for program after functional software reset

enricoantonioli — Mon, 30 Sep 2024 15:43:28 GMT

Hello,

I would like to know after how much time (in milliseconds) from a functional reset sofwtare (SW_FUNC) the flash module is ready for accept erasing and programming.

I did not find this information on the datasheet and often after a software functional reset the programming fails due to MCRS error (PEP).

Can anybody help me? If I insert a delay about 10 ms from reset the programming procedure has success. and without delay programming fails.

Best regards

Re: S32K311 FLASH ready for program after functional software reset

davidtosenovjan — Wed, 02 Oct 2024 15:30:27 GMT

I understand it the way that you need to wait until MCSR[DONE] = 1.

There is no explicit time defined in the documentation.

Re: S32K311 FLASH ready for program after functional software reset

enricoantonioli — Fri, 11 Oct 2024 06:08:26 GMT

Hello David,

Thank you for your answer, but I notice that after reset I must wait for HSE core execute WFI before execute a program or an erase FLASh operation, otherwise it does not works and return the protection error MCRS[PEP].

After the reset and before programming or deleting the FLASH I had to enter the following wait:

while ((IP_MC_ME->PRTN0_CORE2_STAT&MC_ME_PRTN0_CORE2_STAT_WFI_MASK)==0){};/* Waiting for hse core execute WFI */

There is currently no firmware programmed into the HSE and the HSE firmware usage feature flag is disabled.

I did not find any warning about this in either the "S32K3xx Reference Manual" or the "RM00286 HSE_B Firmware Reference Manual".

Can you confirm what I found?

Best regards

Re: S32K311 FLASH ready for program after functional software reset

davidtosenovjan — Tue, 15 Oct 2024 15:26:01 GMT

Do you program same block as BAF is located in? In such case there is such limitation as described below

Re: S32K311 FLASH ready for program after functional software reset

enricoantonioli — Tue, 15 Oct 2024 16:31:40 GMT

Hi David,

my application code can program only the first 512 KB (0x00400000--0x0047FFFF) of the FLASH memory, and if I understand the SBAF use only the address space 0x004F4000--0x004FFFFF.

So why do I still have to wait for HSE enter in WFI state?

I don't have to use the address space reserved for SBAF

Waiting your response

Best Regards

Re: S32K311 FLASH ready for program after functional software reset

davidtosenovjan — Wed, 16 Oct 2024 07:11:55 GMT

According Table 207 above, Block 0 is locked as well. Notice that there are always two blocks locked even with other S32K3.

Apparently only data flash you could access immediately on S32K311.

Re: S32K311 FLASH ready for program after functional software reset

enricoantonioli — Wed, 16 Oct 2024 07:41:20 GMT

Hello David,

thank you very much for your clarification, but if you say "Notice that there are always two blocks locked even with other S32K3", I don't understand why in Table 207 for S32K311 Code Flash Block 1 is NA and not 1?

I suppose that for S32K310 too, that has only block 0 this is locked by HSE during SBAF, is it correct?

Best regards

Re: S32K311 FLASH ready for program after functional software reset

davidtosenovjan — Thu, 17 Oct 2024 08:06:59 GMT

This table does not fit to S32K311 (S32K3x1 fits to S32K341), I will report it as documentation error as on this device, blocks are defined differently.

If I can compare with other sub-derivatives, I suppose both code blocks are locked.