topic Re: Check WEL bit fail in Qspi_Ip_Example_S32K344 in S32K

Check WEL bit fail in Qspi_Ip_Example_S32K344

FelixQi — Tue, 13 Aug 2024 08:26:42 GMT

The version information of the example is as below:

* Autosar Version : 4.7.0
* Autosar Revision : ASR_REL_4_7_REV_0000
* Autosar Conf.Variant :
* SW Version : 3.0.0
* Build Version : S32K3_RTD_3_0_0_D2303_ASR_REL_4_7_REV_0000_20230331

The Serial Flash I use is W25Q16. I've attached the Datasheet as attachment.

I've configured the Mem LUT Operand in below table of ConfigTools:

Write Enable is 06h and Read Status Register-1 is 05h

But when I run the example, when run Qspi_Ip_EraseBlock() in main.c

it runs into Qspi_Ip_WriteEnable(),

After /* send WREN command */, when /* check WEL bit */, the WEL is expected to be 1, but it is read as 0. So the program runs into Mem_ExFls_ExampleAssert().

Is there any wrong configuration or do I miss some important configuration? Expect to your reply. Thanks!

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

davidtosenovjan — Wed, 14 Aug 2024 13:41:16 GMT

What is your /WP pin connection?

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

FelixQi — Thu, 15 Aug 2024 01:24:45 GMT

Hi,

Thank you for your reply!

The /WP(IO2) pin of Flash is connected to PTD12 of S32K344 currently.

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

davidtosenovjan — Thu, 15 Aug 2024 09:54:55 GMT

If so, do you drive this pin to logic 0?

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

FelixQi — Fri, 16 Aug 2024 02:51:54 GMT

Hi,

I don't drive this pin to logic 0 in source code.

I've measured this pin by oscilloscope and it keeps logic 1 during the whole process.

I also tried not connecting this pin, but still meet the same problem.

Besides, I've tried another command "Read JEDEC ID". Below is the sequence in the Flash User Manual:

After I send the read command, I could measure there is data output through DO.

But all data in ReadData keep as 0 after running below API:

qspiStatus = Qspi_Ip_RunReadCommand(instance, 21, 0U, ReadData, NULL_PTR, 3U);//Read JEDEC ID

21 is the LUT index of ReadDeviceId:

/* 21: ReadDeviceId */
(Qspi_Ip_InstrOpType)((Qspi_Ip_InstrOpType)QSPI_IP_LUT_INSTR_CMD | (Qspi_Ip_InstrOpType)QSPI_IP_LUT_PADS_1 | (Qspi_Ip_InstrOpType)159U),
(Qspi_Ip_InstrOpType)(QSPI_IP_LUT_INSTR_STOP)

It seems that the Flash could response the command but the S32K344 could not read correctly.

I've not sure where the problem exists.

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

FelixQi — Fri, 16 Aug 2024 05:19:35 GMT

I've noticed that the value of register QUADSPI->RBDR[0] remains 0x00000000 all the time.

Re: Check WEL bit fail in Qspi_Ip_Example_S32K344

FelixQi — Wed, 21 Aug 2024 01:28:37 GMT

I've missed the READ instruction in the Read Status Register-1 sequence. The problem was solved already.