topic Re: Internal Temperature sensor in S32K

Internal Temperature sensor

Venu_M — Fri, 14 Jul 2023 17:51:54 GMT

Hello NXP team,

How to read MCU internal temperature sensor value through ADC.

How to configure this pin in the configuration.
which pin need to configured for this.

Adc_Sar_Ip_TempSenseEnable();

Adc_Sar_Ip_GetConvData();

Adc_Sar_Ip_TempSenseCalculateTemp();

These Api i used for accessing the values from the register.

After this its Tca1 its going to the vector catch.

its going to the trap_bus_isr and went to vector catch.

Can you tell me the flow or procedure how to access the temperature value (ETS) from MCU chip.

Re: Internal Temperature sensor

Senlent — Thu, 20 Jul 2023 05:36:54 GMT

Hi@Venukumar

please take a look at this post

https://community.nxp.com/t5/S32K-Knowledge-Base/Example-S32K3-Temperature-Sensor-S32-DS-V3-5-RTD-2-0-2/ta-p/1679110

Re: Internal Temperature sensor

Venu_M — Thu, 20 Jul 2023 07:20:56 GMT

Hello Senlent,
Thanks for given this link. I referred this post already.
I'm using 2.0.0 RTD package version.
In a configuration what need to be configure related to tempsensor in the ADC Unit in EB tool.
I configured the Tempsense channel in the ADC unit and for this no port pins available(junction temperature) I'm getting the value also for this channel.
If i use the same flow what you posted in the community, I'm getting high temperature value.

Re: Internal Temperature sensor

Senlent — Thu, 20 Jul 2023 07:47:03 GMT

Hi@Venukumar

I am not familiar with EB, if you have questions about EB, please remember to create a new case and add keywords such as EB or MCAL.

Here are the test results I did based on the demo in the link

What you need to pay attention to is the reference voltage of your ADC module

The Vref I set here is 3.3V, which is 53

Re: Internal Temperature sensor

Venu_M — Thu, 20 Jul 2023 10:38:14 GMT

Hi@Senlent

I'm also using the same 3.3 Vref

But for me Tempsense variable not updating correctly but in data variable its updating.
In Tempsense variable always giving a value as (Tca0).

I posted a new question with a subject name as EB_MCAL.

And after getting the tempsense value how to covert that into degrees.

Re: Internal Temperature sensor

Senlent — Fri, 21 Jul 2023 01:30:04 GMT

Hi@Venukumar

thank you for understanding.
As shown in the test result I provided above, the ADC sampling value is 1402, the converted result is 2947, and the actual temperature is 29.47℃。

Re: Internal Temperature sensor

Venu_M — Fri, 21 Jul 2023 04:49:07 GMT

Hi@Senlent

I too geeting the tempesense value.

How you are converting that into temperature.(your getting 2947 in millivolt its 2.3748mV how you calculated into temperature 29.47degree C.)
In reference manual not specified the formula.

I know the formula like (mV - 0.5)*100 for temperature calculation.

Is there any formula is there to convert?

By using the formula the junction temperature calculated like this mentioned.

Re: Internal Temperature sensor

Senlent — Fri, 21 Jul 2023 05:44:43 GMT

Hi@Venukumar

You can check the routine provided by me, you will find that the function of calculating temperature has been given in the driver provided by RTD

This function is consistent with the calculation formula given in the data sheet

Re: Internal Temperature sensor

Venu_M — Fri, 21 Jul 2023 12:53:38 GMT

Hi@Senlent

I used that Api().

Adc_Sar_Ip_TempSenseGetTemp() this Api is given value as 616 , I don't know how to get this into temperature.

Adc_Sar_Ip_TempSenseCalculateTemp() this Api given value as 569.

Not able to get the temperature in the degrees.

I can use one Api among these 3 Api's, I can get the temperature correct.
For the first one we need ADC sampling data, For the second api no need of any data directly we can call the api and get the temp through the sensor correct?
Third one also we can able to use?

Can you tell me the flow of Api which one i need to call first.

Adc_Sar_Ip_TempSenseEnable(AdcHwUnit_0);

data1 = Adc_Sar_Ip_GetConvData(AdcHwUnit_0, ADC_SAR_USED_CH);

Tempsense = Adc_Sar_Ip_TempSenseCalculateTemp(AdcHwUnit_0,0,data1);

Adc_Sar_Ip_TempSenseGetTemp(AdcHwUnit_0,0,&temperature);

Adc_Sar_Ip_TempSenseDisable(AdcHwUnit_0);

Like this i called the Api's , whether it is correct?

I'm asking lots of question sorry for that !!!

Re: Internal Temperature sensor

Senlent — Mon, 24 Jul 2023 02:43:31 GMT

Hi@Venukumar

Your understanding is correct, but you only need to use one of them.
Also you don't have to call Adc_Sar_Ip_TempSenseEnable/Disable every time.

Re: Internal Temperature sensor

jack-joker — Tue, 30 Jul 2024 06:30:23 GMT

Could You send it to help you with your journey？thanks

Re: Internal Temperature sensor

jack-joker — Fri, 02 Aug 2024 18:59:08 GMT

I missed your reply because I didn't read the mail, I'm sorry for that! Now I've solved this problem, but a new problem has arisen about CAN communication. How do I send you an email?