topic Re: Explaining S32K1xx Pad Types in S32K

Explaining S32K1xx Pad Types

stephandewit1 — Wed, 18 Jul 2018 17:19:37 GMT

I need some more information related to the different S32K148 pad types.

From the document "S32K148_IO_Signal_Description_Input_Multiplexing" Pinout sheet I see the following pad names for each pin.

p_gnd_mv
p_io_5ma_mv
p_io_20ma_mv
p_io_ae_mv
p_io_quadspi_mv
p_io_rst_mv
p_pwr_mv
p_vdda_mv

In the S32K1xx datasheet (Rev 6 01/2018) Table 31 it has the following note.

7. This is the maximum operating frequency (fop) for LPSPI0 with medium PAD type only. Otherwise, the maximum operating frequency (fop) is 12 Mhz

11. Maximum operating frequency (fop ) is 12 MHz irrespective of PAD type and LPSPI instance

12. Applicable for LPSPI0 only with medium PAD type, with maximum operating frequency (fop) as 14 MHz

How do I map "medium PAD type" to the pad names above?

This all relates to the maximum frequency and minimum data setup time for LPSPI0 in master mode using the following pins

PTD16 : SPI0_SDI
PTD15 : SPI0_SCK
PTB5 : SPIO_CS
PTB4 : SPIO_SDO

Is the maximum frequency 14MHz or 12MHz in HSRUN?

Is the minimum data setup time 37ns or 32ns in HSRUN?

Re: Explaining S32K1xx Pad Types

dianabatrlova — Fri, 20 Jul 2018 08:25:46 GMT

Hi Stephan,

For example, you can configure the pin PTB5 for the LPSPI0 like below.

Should be used GPIO-HD pins (specified in S32K148 IO_Signal_Description_Input_Multiplexing.xlsx) and set PCR_DSE = 1.

PORTB->PCR[5] &= ~PORT_PCR_MUX_MASK; /* Set MUX=0 temporarily */

PORTB->PCR[5] |= PORT_PCR_MUX(4) | /* MUX=4: Select LPSPI0_PCS0 on PTB5 */

PORT_PCR_DSE_MASK; /* DSE=1: High drive strength is configured */

The maximum operating frequency HSRUN at 3V3 VDD is 14MHz. In that case is minimum data setup time 32ns.

Best regards,

Diana

Re: Explaining S32K1xx Pad Types

stephandewit1 — Thu, 26 Jul 2018 18:01:39 GMT

Hi Diana,

Thanks for your reply.

From your response it seems like only the SPI_CS pin (PTB5) in this case needs PCR_DSE set to 1.

Is this required for the SPI_SCK pin, PTD15 in this case?

Does SPI_SCK require any special configuration outside configuring PORT_PCR_MUX = 4?

As well in our application we are controlling the SPI0 Chip Select manually, configuring it as a GPIO, PORT_PCR_MUX = 1. (see code below)

PORTB->PCR[5] = PORT_PCR_MUX(1); // CS
PTB->PDDR |= (1 << 5); // set as output
#define FLASH_CHIP_SELECT PTB->PCOR = (1 << 5)
#define FLASH_CHIP_DESELECT PTB->PSOR = (1 << 5)

Does using the pin, PTB5, in this way still require PCR_DSE set to 1?

Is the maximum operating frequency for LPSPI0 in HSRUN at 3V3 VDD still 14MHz?

Thanks,

Stephan

Re: Explaining S32K1xx Pad Types

systems1 — Sat, 14 Dec 2019 05:10:20 GMT

How to get the IO Signal Description Input Multiplexing sheet for S32K148 microcontroller?

S32K148 reference doc is not attached with IO Signal Description Input Multiplexing sheet for S32K148 microcontroller

Hello Diana Batrioa

Can you help me to get the document as mentioned above?

Re: Explaining S32K1xx Pad Types

dianabatrlova — Mon, 16 Dec 2019 12:09:08 GMT

Hello,

Please, download the Reference Manual and open it in the PC

https://www.nxp.com/docs/en/reference-manual/S32K-RM.pdf

the document can be seen in the attachment:

I hope it helps.

BR,

Diana

Re: Explaining S32K1xx Pad Types

systems1 — Wed, 18 Dec 2019 05:03:57 GMT

Hello Diana

Sorry to report. In the suggested doc, the full description of pad description is blocked.

Regards,

Kanakaraju