https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953142#M3772 没负载，烧录板外部没任何负载 和之前前的烧录板一样 烧录成功后 只测输出 电压 检测芯片烧录成功是否 外部无任何负载 只是测一下电压正常就可以 但现在新买的烧录板 烧录完后的软件 电流过高 烧录板型号和之前12mA的烧录板一样 Thu, 12 Sep 2024 06:55:15 GMT quanwang 2024-09-12T06:55:15Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1952966#M3767 <P>The 5600 development board purchased on the official website is supplied with 12V power supply. After burning the 5600 chip through the normal operation process, when using user_mode to verify the chip output voltage, the current of the development board is more than 2A abnormal, and the normal value should be 12mA. May I ask if there is any problem with the burning board that needs to be repaired, or is there any other verification scheme</P> Thu, 12 Sep 2024 03:45:01 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1952966#M3767 quanwang 2024-09-12T03:45:01Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953102#M3769 <P>5600是你自己做的OTP吗？做过OTP以后上电就有2A的静态电流这么大？</P> <P>&nbsp;</P> <P>&nbsp;</P> Thu, 12 Sep 2024 06:29:37 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953102#M3769 guoweisun 2024-09-12T06:29:37Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953123#M3770 通过GUI软件自己配置的OTP，只有烧录OTP后 进入user mode 或检测输出电压 电源显示2.5A电流 我们之前的烧录板就只有12mA 用新买的就是2.5A 操作流程和配置的OTP是一致的 可能是哪里的问题？？ Thu, 12 Sep 2024 06:43:45 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953123#M3770 quanwang 2024-09-12T06:43:45Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953134#M3771 <P>在没有负载的情况下12V的电源电流到了2.5A？</P> <P>你看看后面接负载了吗？</P> Thu, 12 Sep 2024 06:49:24 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953134#M3771 guoweisun 2024-09-12T06:49:24Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953142#M3772 没负载，烧录板外部没任何负载 和之前前的烧录板一样 烧录成功后 只测输出 电压 检测芯片烧录成功是否 外部无任何负载 只是测一下电压正常就可以 但现在新买的烧录板 烧录完后的软件 电流过高 烧录板型号和之前12mA的烧录板一样 Thu, 12 Sep 2024 06:55:15 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953142#M3772 quanwang 2024-09-12T06:55:15Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953165#M3773 <P>2.5A的静态电流不正常可能要把芯片烧坏或者已经坏掉了。</P> <P>烧录板是我们官方的socket板子吗？</P> Thu, 12 Sep 2024 07:04:49 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953165#M3773 guoweisun 2024-09-12T07:04:49Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953173#M3774 是的 SKTEVM板子 Thu, 12 Sep 2024 07:11:06 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953173#M3774 quanwang 2024-09-12T07:11:06Z https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953180#M3775 <P>那你还是换回来以前的板子烧录吧，我估计是板子除了问题。</P> Thu, 12 Sep 2024 07:13:59 GMT https://community.nxp.com/t5/Power-Management/5600-development-board/m-p/1953180#M3775 guoweisun 2024-09-12T07:13:59Z