MQX Software SolutionsのトピックRe: How to set SDHC clock to 50MHz?

How to set SDHC clock to 50MHz?

naftalir — Mon, 19 Nov 2012 11:36:24 GMT

Hi,

I've tested the SDCLK and noticed it works default in 20MHz clock, so i've managed to chage it to 40MHz but not to 50MHz.

My code looks like that:

/* Set SDCLK to 40Mhz*/

esdhc_ptr->SYSCTL &= 0xFFFFFFF7; //Disable the SD Clock

esdhc_ptr->SYSCTL &= 0xFFFF00FF; //Setting the Prescaler to 0

esdhc_ptr->SYSCTL |= 0x00000020; //Setting the Divisor to 3

esdhc_ptr->SYSCTL |= 0x00000008; //Enable the SD Clock

esdhc_ptr->SYSCTL |= 0x00000004; //Remain the SDHC clock always enabled

Re: How to set SDHC clock to 50MHz?

naftalir — Mon, 19 Nov 2012 11:38:20 GMT

****I've accidently pressed "Send Button".

My question is: how to set the registers in order to provide clock of 50MHz, when the CPU Clock is 120MHz?

Thank you all.

Re: How to set SDHC clock to 50MHz?

c0170 — Mon, 19 Nov 2012 12:35:44 GMT

Hello naftalir,

I assume you are using Kinetis platform. There''s section in Reference Manual for your MCU where this equation is written:

Clock frequency = Base clock / (prescaler x divisor)

There's not much to do here to set desired 50 MHz with 120 MHz source clock. Closest you can get is 40 MHz. You can anyway change the bus clock.

Regards,

MartinK

Re: How to set SDHC clock to 50MHz?

naftalir — Mon, 19 Nov 2012 12:45:29 GMT

Thank you Kojto,

If i change the bus clock it will change the whole system performance..

Can i do it somehow without affected the system?

Re: How to set SDHC clock to 50MHz?

c0170 — Mon, 19 Nov 2012 13:02:08 GMT

Hello,

I forgot to mention, there's chapter in Reference manual dedicated to Clock distribution with the same name.

This is based on Kinetis 40: There're 4 possible clock sources :

System clock

MCGPPLLCLK/MCGFLLCLK

OSCERCLK

SDHC0_CLKIN

You can select one of these clock sources for SDHC module and customize divider to have 50 MHz.

Regards,

MartinK

Re: How to set SDHC clock to 50MHz?

naftalir — Mon, 19 Nov 2012 13:22:14 GMT

Again, Thank you Kojto but may i ask you for example on how to change the clock source?

i cant seem to find it..

Thank you.

Re: How to set SDHC clock to 50MHz?

c0170 — Tue, 20 Nov 2012 06:29:42 GMT

Hello,

SIM_SOPT2[SDHCSRC] register specifies Clock for SDHC peripheral. I note that you did not clarify your target MCU, therefore everything what I have written is for K40. Slight changes might be for different MCU.

Regards,

MartinK

Re: How to set SDHC clock to 50MHz?

naftalir — Tue, 20 Nov 2012 07:24:36 GMT

Again, Thank you for your true help! :smileyhappy:

I forgot to mention my MCU: K60F120M, if there is any change to what you wrote i will be happy to know :smileyhappy:

Sincerely yours,

Naftali.

Re: How to set SDHC clock to 50MHz?

MarkP_ — Tue, 20 Nov 2012 08:31:48 GMT

Hi,

I created a test project with CW 10.2 and selected PE-support.

The configuration is shown in picture below and register initialization is in attached C-file.

~Mark

Re: How to set SDHC clock to 50MHz?

MarkP_ — Tue, 20 Nov 2012 08:35:59 GMT

I think 50MHz cannot be generated from 120MHz CPU clock, need to be 100MHz.

Re: How to set SDHC clock to 50MHz?

naftalir — Tue, 20 Nov 2012 12:29:53 GMT

Hi Markku!

Thank you for your help.

I did managed to get 50MHz with the source of the OSC0ERCLK:

/* My Code for this is: */

SDHC_MemMapPtr esdhc_ptr = SDHC_BASE_PTR;

SIM_MemMapPtr sim_ptr = (SIM_MemMapPtr)0x40047000; //Base address of the SIM

/* Set the SDHC clk source to OSC0 = 50MHz */

sim_ptr->SOPT2 |= 0x20000000; //Set ESDHCSRC clk to OSC0ERCLK

esdhc_ptr->SYSCTL &= 0xFFFF00FF; //Disable the Prescaler

esdhc_ptr->SYSCTL &= 0xFFFFFF0F; //Disable the Divisor

Thank you all for your help: Kojto and Markku!!

:smileyhappy: