topic I have some problems with using MQX4.2, my program is often stuck in MQX Software Solutions

I have some problems with using MQX4.2, my program is often stuck

wyflsxy — Tue, 15 Dec 2015 03:47:23 GMT

hello everybody,

I have some problems with using MQX4.2, my program is often stuck in the following code in idletask.c

while (1) {

#if !defined(MQX_ENABLE_IDLE_LOOP) || MQX_ENABLE_IDLE_LOOP

if (++kernel_data->IDLE_LOOP.IDLE_LOOP1 == 0) {

if (++kernel_data->IDLE_LOOP.IDLE_LOOP2 == 0) {

if (++kernel_data->IDLE_LOOP.IDLE_LOOP3 == 0) {

++kernel_data->IDLE_LOOP.IDLE_LOOP4;

}

#endif /* !defined(MQX_ENABLE_IDLE_LOOP) || MQX_ENABLE_IDLE_LOOP */

it looks like the task scheduling problems, but when I only have one main_task, and then I was in the debug I2C

it was stuck there, could anybody know what's the problem?

Re: I have some problems with using MQX4.2, my program is often stuck

soledad — Wed, 16 Dec 2015 19:56:58 GMT

Hi,

Are you using a custom board? I've seeing this issue when the board has a hardware problems for example bad clock configurations or bad jumper configuration.

Are you using interrupts??

Could you please share the code in order to reproduce the issue?

Have a great day,
Sol

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: I have some problems with using MQX4.2, my program is often stuck

wyflsxy — Thu, 17 Dec 2015 01:47:45 GMT

Hello, my application will not be stuck in there by now, but the question is the I2C waveform is always the same now,when I used the function of I2C_DRV_MasterSendDataBlocking (chan, & device, NULL, 0, pdata, 1, 200); no matter how do I change the value of the pdata,the waveform of I2C was same,the SDA line only have the start and stop bits, middle of it was full of zero

I think the board is no problem, I have try the custom board of frdmk64f and my own board, there have the same problem In MQX4.2 with KSDK1.2 on kds3.0

my code is below,did I have some wrong with it,and when I use the example of "i2c_blocking_master_example_frdmk64f",the waveform is same,I don't know what's wrong with it

Oscilloscope test out the waveform as shown, when I change the value sent about pdata,the wave is same as the photo

void main_task( task_param_t init_data ){

_task_id rx_tid;

_task_id tx_tid;

TASK_PARAMS task_p = {0};

uint8_t result = 0;

uint8_t temp;

hardware_init();

OSA_Init();

button_init();

i2c_init(0);

uint8_t i;

uint8_t length = 10;

uint8_t data[length];

for(i = 0;i<length;i++){

data[i] = i;

}

while(1){

i2c_sendbuf(0,data,length);

_time_delay(5);

};

}

_WEAK_FUNCTION(void hardware_init(void)) {

uint8_t i;

/* enable clock for PORTs */

for (i = 0; i < PORT_INSTANCE_COUNT; i++)

{

CLOCK_SYS_EnablePortClock(i);

}

/* Init board clock */

BOARD_ClockInit();

/* In case IO sub is turned off, dbg console should be used for printing */

#if !BSPCFG_ENABLE_IO_SUBSYSTEM

dbg_uart_init(); //wangyufei

#endif

}

void i2c_init(uint8_t chan){

uint32_t i = 0;

// i2c master state

i2c_master_state_t master;

// i2c device configuration

configure_i2c_pins(0);

configure_i2c_pins(1);

// Initialize i2c master

I2C_DRV_MasterInit(0, &master);

I2C_DRV_MasterInit(1, &master);

}

int i2c_sendbuf(uint8_t chan,uint8_t *data,uint8_t length)

{

uint32_t i = 0;

i2c_status_t status1;

uint8_t pdata[10];

for(i = 0; i < DATA_LENGTH; i++)

{

txBuff[i] = i + 1;

}

uint8_t result;

for(i = 0;i<10;i++)

pdata[i] = i+3;

pdata[0] = 0x80;

pdata[1] = 0xF3;

result = I2C_DRV_MasterSendDataBlocking(chan, &device,

pdata, 1,pdata, 2, 200);

// Delay to wait slave received data

OSA_TimeDelay(10);

// _time_delay(5);

pdata[0] = 0x81;

result = I2C_DRV_MasterSendDataBlocking(chan, &device,

pdata, 1,pdata, 1, 200);

// Clear rxBuff

for(i = 0; i < count; i++)

{

rxBuff[i] = 0;

}

// Master receives count byte data from slave

result = I2C_DRV_MasterReceiveDataBlocking(chan, &device,

NULL, 0, rxBuff, 1, 200);

OSA_TimeDelay(5);

}