topic LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working in Layerscape

LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working

arunkr — Mon, 07 Dec 2015 12:08:38 GMT

Hi,

I am having LS1021AIOT board, (LS1021A Rev 1.0, IOT boar Rev X2).
The Realtek RTL8365MB 4+1 port Gigabit ethernet Switch in connected in eth2 (eTSEC3).

SDK is Yocto (QorIQ-SDK-V1.8).

I cannot communicate through the switch on this reference board with this code. ie, LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working.

The RCW for eth3 is set for RGMII (000). In the Dts file in kernel, eth2 was set as rgmii-id, and in gianfar.c it was checking only rgmii. I have changed it.
Now on booting, it is verified that code runs through "Configuring RGMII mode" in gianfar.c. If I up/down eth2, it gets configured as RGMII (code runs, not sure whether PHY actually configured).

I can ping from on device connected to this switch to another device connected in the same switch. But I cannot communicate with other network.

brctl showstp br-lan command shows:

root@OpenWrt:~# brctl showstp br-lan

br-lan

bridge id 7fff.001f7b6301aa

designated root 7fff.001f7b6301aa

root port 0 path cost 0

max age 20.00 bridge max age 20.00

hello time 2.00 bridge hello time 2.00

forward delay 2.00 bridge forward delay 2.00

ageing time 300.00

hello timer 0.64 tcn timer 0.00

topology change timer 0.00 gc timer 117.76

flags

eth0

port id 8001 state disabled

designated root 7fff.001f7b6301aa path cost 4

designated bridge 7fff.001f7b6301aa message age timer 0.00

designated port 8001 forward delay timer 0.00

designated cost 0 hold timer 0.00

flags

eth1

port id 8002 state disabled

designated root 7fff.001f7b6301aa path cost 100

designated bridge 7fff.001f7b6301aa message age timer 0.00

designated port 8002 forward delay timer 0.00

designated cost 0 hold timer 0.00

flags

The default br-lan bridge interface is up by default, and both eth0 and eth1 is added as shown above. I cannot ping from eth0 or eth1 to this eth2 How this can be resolved ?

Re: LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working

Pavel — Mon, 14 Dec 2015 05:10:37 GMT

It looks like that configuration of your network is incorrect. It looks like that gateway and DNS server is not defined for your board.

Have a great day,
Pavel

-----------------------------------------------------------------------------------------------------------------------
Note: If this post answers your question, please click the Correct Answer button. Thank you!
-----------------------------------------------------------------------------------------------------------------------

Re: LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working

arunkr — Tue, 15 Dec 2015 14:48:55 GMT

Hi Pavel Chubakov,

As per the documentation available on Freescale Website, (http://cache.nxp.com/files/soft_dev_tools/doc/support_info/LS1021A-SDK-V1.1-ARM-SOURCE_RMF.txt?fpsp=1&WT_TYPE=Supporting… ) about RTL L2 switch, it is saying that:

"The RTL L2 switch will be initialized on boot, the interface name is "eth2", use below command to add it to bridge:

$ ifconfig eth2 up

$ brctl addif br-lan eth2"

I have done the step.

If I run 'ethtool eth2' command on fsl-image-rds, I am getting the below :

# ethtool eth2

Settings for eth2:

Supported ports: [ MII ]

Supported link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Full

Supported pause frame use: Symmetric Receive-only

Supports auto-negotiation: Yes

Advertised link modes: 10baseT/Half 10baseT/Full

100baseT/Half 100baseT/Full

1000baseT/Full

Advertised pause frame use: No

Advertised auto-negotiation: Yes

Speed: 1000Mb/s

Duplex: Full

Port: MII

PHYAD: 2

Transceiver: external

Auto-negotiation: off

Supports Wake-on: g

Wake-on: d

Current message level: 0x0000003f (63)

drv probe link timer ifdown ifup

Link detected: yes

It shows the eth2 is configured in MII.

I am using LS1021A-IoT Gateway Reference Design SDK Source ISO (REV 1.8).The Hardware is configured for RGMII, and in device tree by default it was initializing as MII only, not RGMII. I have change it to rgmii-id now, and on booting, I gets prints of eth2 configured in RGMII. Still on 'ethtool eth2' command, I am getting MII only. What could be the problem ?

Re: LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working

arunkr — Mon, 25 Jan 2016 12:56:19 GMT

Hi Pavel,

We have solved the issue, the issue was with RTL switch initialization. The SDK provided with the reference board was not initializing the RTL switch, so we integrated user space application for configuring the RTL Switch over DSPI, now its working.

Re: LS1021AIOT eTSEC3 - RTL8365 ethernet switch not working

wilkxt — Sun, 22 Dec 2019 11:14:55 GMT

I have the same problem, where you change RTL switch initialization? I can't find this in the current SDK?

this SDk https://nxp.flexnetoperations.com/control/frse/product?child_plneID=684021&cert_num=727175607&ver=ARC support LS1021A-IOT board?