[ 7796.544102] usb 3-6: new high-speed USB device number 106 using xhci_hcd
[ 7796.696572] usb 3-6: New USB device found, idVendor=0bda, idProduct=8152, bcdDevice=20.00
[ 7796.696580] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7796.696582] usb 3-6: Product: USB 10/100 LAN
[ 7796.696583] usb 3-6: Manufacturer: Realtek
[ 7796.696585] usb 3-6: SerialNumber: 00309181505F
[ 7796.718951] usbcore: registered new device driver r8152-cfgselector
[ 7796.856347] r8152-cfgselector 3-6: reset high-speed USB device number 106 using xhci_hcd
[ 7797.048760] r8152 3-6:1.0: skip request firmware
[ 7797.080728] r8152 3-6:1.0 eth0: v1.12.13
[ 7797.080772] usbcore: registered new interface driver r8152
[ 7797.090255] usbcore: registered new interface driver cdc_ether
[ 7797.128387] r8152 3-6:1.0 enx00309181505f: renamed from eth0
[ 7798.930511] IPv6: ADDRCONF(NETDEV_CHANGE): enx00309181505f: link becomes ready
[ 7798.930761] r8152 3-6:1.0 enx00309181505f: carrier on
[ 7803.483072] r8152-cfgselector 3-6: USB disconnect, device number 106
[ 7845.660170] usb 3-5: new high-speed USB device number 107 using xhci_hcd
[ 7846.072226] usb 3-5: Device not responding to setup address.
[ 7846.280193] usb 3-5: Device not responding to setup address.
[ 7846.492176] usb 3-5: device not accepting address 107, error -71
[ 7846.828173] usb 3-5: new high-speed USB device number 108 using xhci_hcd
[ 7846.984549] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7846.984556] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7846.984558] usb 3-5: Product: Marvell Wireless Device
[ 7846.984560] usb 3-5: Manufacturer: Marvell
[ 7846.984561] usb 3-5: SerialNumber: 0000000000000000
[ 7846.985489] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7846.985495] VID/PID = 1286/2052, Boot2 version = 4000
[ 7846.985502] Attach moal handle ops, card interface type: 0x404
[ 7846.985506] No module param cfg file specified
[ 7846.985509] rx_work=1 cpu_num=18
[ 7846.985523] Attach mlan adapter operations.card_type is 0x404.
[ 7846.988175] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7847.381647] fw_dnld: 610252 bytes downloaded
[ 7848.126944] usb 3-5: USB disconnect, device number 108
[ 7848.156178] USB: unregister device
[ 7848.156200] Free module params
[ 7848.440183] usb 3-5: new high-speed USB device number 109 using xhci_hcd
[ 7848.602304] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7848.602313] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7848.602315] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7848.602316] usb 3-5: Manufacturer: Marvell
[ 7848.602318] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7848.608199] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7848.608205] VID/PID = 1286/204E, Boot2 version = 3201
[ 7848.608207] woal_usb_probe: invalid endpoint assignment
[ 7848.608246] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7848.608248] VID/PID = 1286/204E, Boot2 version = 3201
[ 7848.608249] woal_usb_probe: invalid endpoint assignment
[ 7848.609294] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7848.609297] VID/PID = 1286/204E, Boot2 version = 3201
[ 7848.609304] Attach moal handle ops, card interface type: 0x404
[ 7848.609309] No module param cfg file specified
[ 7848.609312] rx_work=1 cpu_num=18
[ 7848.609327] Attach mlan adapter operations.card_type is 0x404.
[ 7848.612191] WLAN FW is active
[ 7848.612193] on_time is 7848848029900
[ 7848.655523] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7848.655534] max_p2p_conn = 8, max_sta_conn = 8
[ 7848.663556] wlan: uap0 set max_mtu 2000
[ 7848.669850] wlan: version = USB8997---16.68.1.p183-MM5X16344.p3-GPL-(FP92) 
[ 7848.694530] usb 3-5 wlx9c50d1e343a4: renamed from uap0
[ 7848.739075] wlan: Stoping AP
[ 7848.739083] wlan: AP stopped
[ 7848.840619] wlan: wlx9c50d1e343a4 START SCAN
[ 7848.844417] Card is removed: -71
[ 7848.844452] usb 3-5: USB disconnect, device number 109
[ 7848.844515] Card is removed: -71
[ 7848.844635] Card is removed: -71
[ 7848.844719] Card is removed: -108
[ 7848.844722] Card is removed: -71
[ 7848.844797] Card is removed: -108
[ 7848.844835] Card is removed: -108
[ 7848.844926] IOCTL failed: 00000000867af1f5 id=0x10000, sub_id=0x10003 action=1, status_code=0x80000007
[ 7848.932180] USB: unregister device
[ 7848.964278] Free module params
[ 7849.248183] usb 3-5: new high-speed USB device number 110 using xhci_hcd
[ 7849.400566] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7849.400574] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7849.400576] usb 3-5: Product: Marvell Wireless Device
[ 7849.400577] usb 3-5: Manufacturer: Marvell
[ 7849.400579] usb 3-5: SerialNumber: 0000000000000000
[ 7849.401519] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7849.401524] VID/PID = 1286/2052, Boot2 version = 4000
[ 7849.401533] Attach moal handle ops, card interface type: 0x404
[ 7849.401538] No module param cfg file specified
[ 7849.401541] rx_work=1 cpu_num=18
[ 7849.401555] Attach mlan adapter operations.card_type is 0x404.
[ 7849.404179] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7849.794668] fw_dnld: 610252 bytes downloaded
[ 7850.543935] usb 3-5: USB disconnect, device number 110
[ 7850.572185] USB: unregister device
[ 7850.572245] Free module params
[ 7850.856176] usb 3-5: new high-speed USB device number 111 using xhci_hcd
[ 7851.018264] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7851.018272] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7851.018275] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7851.018276] usb 3-5: Manufacturer: Marvell
[ 7851.018279] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7851.024190] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7851.024196] VID/PID = 1286/204E, Boot2 version = 3201
[ 7851.024198] woal_usb_probe: invalid endpoint assignment
[ 7851.024238] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7851.024240] VID/PID = 1286/204E, Boot2 version = 3201
[ 7851.024241] woal_usb_probe: invalid endpoint assignment
[ 7851.025152] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7851.025154] VID/PID = 1286/204E, Boot2 version = 3201
[ 7851.025163] Attach moal handle ops, card interface type: 0x404
[ 7851.025167] No module param cfg file specified
[ 7851.025171] rx_work=1 cpu_num=18
[ 7851.025187] Attach mlan adapter operations.card_type is 0x404.
[ 7851.028177] WLAN FW is active
[ 7851.028179] on_time is 7851264012650
[ 7851.071149] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7851.071160] max_p2p_conn = 8, max_sta_conn = 8
[ 7851.079185] wlan: uap0 set max_mtu 2000
[ 7851.085414] wlan: version = USB8997---16.68.1.p183-MM5X16344.p3-GPL-(FP92) 
[ 7851.111109] usb 3-5 wlx9c50d1e343a4: renamed from uap0
[ 7851.151526] wlan: Stoping AP
[ 7851.151535] wlan: AP stopped
[ 7851.257801] wlan: wlx9c50d1e343a4 START SCAN
[ 7851.261661] Card is removed: -71
[ 7851.261698] usb 3-5: USB disconnect, device number 111
[ 7851.261760] Card is removed: -71
[ 7851.261880] Card is removed: -71
[ 7851.261967] Card is removed: -108
[ 7851.261972] Card is removed: -71
[ 7851.262042] Card is removed: -108
[ 7851.262080] Card is removed: -108
[ 7851.262129] IOCTL failed: 00000000cec5bf28 id=0x10000, sub_id=0x10003 action=1, status_code=0x80000007
[ 7851.352198] USB: unregister device
[ 7851.388301] Free module params
[ 7851.668177] usb 3-5: new high-speed USB device number 112 using xhci_hcd
[ 7851.824551] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7851.824558] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7851.824560] usb 3-5: Product: Marvell Wireless Device
[ 7851.824562] usb 3-5: Manufacturer: Marvell
[ 7851.824563] usb 3-5: SerialNumber: 0000000000000000
[ 7851.825525] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7851.825531] VID/PID = 1286/2052, Boot2 version = 4000
[ 7851.825539] Attach moal handle ops, card interface type: 0x404
[ 7851.825544] No module param cfg file specified
[ 7851.825548] rx_work=1 cpu_num=18
[ 7851.825562] Attach mlan adapter operations.card_type is 0x404.
[ 7851.828254] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7852.225791] fw_dnld: 610252 bytes downloaded
[ 7852.974691] usb 3-5: USB disconnect, device number 112
[ 7852.996188] USB: unregister device
[ 7852.996211] Free module params
[ 7853.288182] usb 3-5: new high-speed USB device number 113 using xhci_hcd
[ 7853.446301] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7853.446311] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7853.446312] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7853.446314] usb 3-5: Manufacturer: Marvell
[ 7853.446316] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7853.452232] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7853.452238] VID/PID = 1286/204E, Boot2 version = 3201
[ 7853.452239] woal_usb_probe: invalid endpoint assignment
[ 7853.452281] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7853.452282] VID/PID = 1286/204E, Boot2 version = 3201
[ 7853.452284] woal_usb_probe: invalid endpoint assignment
[ 7853.453285] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7853.453287] VID/PID = 1286/204E, Boot2 version = 3201
[ 7853.453294] Attach moal handle ops, card interface type: 0x404
[ 7853.453299] No module param cfg file specified
[ 7853.453303] rx_work=1 cpu_num=18
[ 7853.453322] Attach mlan adapter operations.card_type is 0x404.
[ 7853.456180] WLAN FW is active
[ 7853.456182] on_time is 7853692012942
[ 7853.489107] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7853.489119] max_p2p_conn = 8, max_sta_conn = 8
[ 7853.496930] wlan: uap0 set max_mtu 2000
[ 7853.503162] wlan: version = USB8997---16.68.1.p183-MM5X16344.p3-GPL-(FP92) 
[ 7853.521231] usb 3-5 wlx9c50d1e343a4: renamed from uap0
[ 7853.567077] wlan: Stoping AP
[ 7853.567085] wlan: AP stopped
[ 7853.671015] wlan: wlx9c50d1e343a4 START SCAN
[ 7853.674816] Card is removed: -71
[ 7853.674849] usb 3-5: USB disconnect, device number 113
[ 7853.674911] Card is removed: -71
[ 7853.675032] Card is removed: -71
[ 7853.675076] Card is removed: -108
[ 7853.675113] Card is removed: -108
[ 7853.675115] Card is removed: -108
[ 7853.675151] Card is removed: -108
[ 7853.675196] IOCTL failed: 00000000371180d9 id=0x10000, sub_id=0x10003 action=1, status_code=0x80000007
[ 7853.760185] USB: unregister device
[ 7853.816282] Free module params
[ 7854.096185] usb 3-5: new high-speed USB device number 114 using xhci_hcd
[ 7854.248564] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7854.248571] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7854.248573] usb 3-5: Product: Marvell Wireless Device
[ 7854.248575] usb 3-5: Manufacturer: Marvell
[ 7854.248576] usb 3-5: SerialNumber: 0000000000000000
[ 7854.249516] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7854.249522] VID/PID = 1286/2052, Boot2 version = 4000
[ 7854.249530] Attach moal handle ops, card interface type: 0x404
[ 7854.249534] No module param cfg file specified
[ 7854.249537] rx_work=1 cpu_num=18
[ 7854.249551] Attach mlan adapter operations.card_type is 0x404.
[ 7854.252187] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7854.644063] fw_dnld: 610252 bytes downloaded
[ 7855.384073] usb 3-5: USB disconnect, device number 114
[ 7855.416198] USB: unregister device
[ 7855.416230] Free module params
[ 7855.692184] usb 3-5: new high-speed USB device number 115 using xhci_hcd
[ 7855.846301] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7855.846309] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7855.846311] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7855.846313] usb 3-5: Manufacturer: Marvell
[ 7855.846314] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7855.852317] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7855.852322] VID/PID = 1286/204E, Boot2 version = 3201
[ 7855.852324] woal_usb_probe: invalid endpoint assignment
[ 7855.852401] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7855.852405] VID/PID = 1286/204E, Boot2 version = 3201
[ 7855.852409] woal_usb_probe: invalid endpoint assignment
[ 7855.853287] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7855.853289] VID/PID = 1286/204E, Boot2 version = 3201
[ 7855.853297] Attach moal handle ops, card interface type: 0x404
[ 7855.853302] No module param cfg file specified
[ 7855.853306] rx_work=1 cpu_num=18
[ 7855.853323] Attach mlan adapter operations.card_type is 0x404.
[ 7855.856192] WLAN FW is active
[ 7855.856195] on_time is 7856092022916
[ 7855.899241] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7855.899259] max_p2p_conn = 8, max_sta_conn = 8
[ 7855.907154] wlan: uap0 set max_mtu 2000
[ 7855.913414] wlan: version = USB8997---16.68.1.p183-MM5X16344.p3-GPL-(FP92) 
[ 7855.933235] usb 3-5 wlx9c50d1e343a4: renamed from uap0
[ 7855.969676] wlan: Stoping AP
[ 7855.969690] wlan: AP stopped
[ 7856.080644] wlan: wlx9c50d1e343a4 START SCAN
[ 7856.084479] Card is removed: -71
[ 7856.084557] Card is removed: -71
[ 7856.084573] usb 3-5: USB disconnect, device number 115
[ 7856.084679] Card is removed: -71
[ 7856.084800] Card is removed: -71
[ 7856.084877] Card is removed: -108
[ 7856.084918] Card is removed: -108
[ 7856.084957] Card is removed: -108
[ 7856.085094] IOCTL failed: 000000005b85698e id=0x10000, sub_id=0x10003 action=1, status_code=0x80000007
[ 7856.164190] USB: unregister device
[ 7856.204279] Free module params
[ 7856.484189] usb 3-5: new high-speed USB device number 116 using xhci_hcd
[ 7856.636604] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7856.636611] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7856.636613] usb 3-5: Product: Marvell Wireless Device
[ 7856.636615] usb 3-5: Manufacturer: Marvell
[ 7856.636616] usb 3-5: SerialNumber: 0000000000000000
[ 7856.637534] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7856.637546] VID/PID = 1286/2052, Boot2 version = 4000
[ 7856.637566] Attach moal handle ops, card interface type: 0x404
[ 7856.637571] No module param cfg file specified
[ 7856.637575] rx_work=1 cpu_num=18
[ 7856.637593] Attach mlan adapter operations.card_type is 0x404.
[ 7856.640194] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7857.031357] fw_dnld: 610252 bytes downloaded
[ 7857.780944] usb 3-5: USB disconnect, device number 116
[ 7857.800189] USB: unregister device
[ 7857.800205] Free module params
[ 7858.116184] usb 3-5: new high-speed USB device number 117 using xhci_hcd
[ 7858.278307] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7858.278314] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7858.278316] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7858.278318] usb 3-5: Manufacturer: Marvell
[ 7858.278320] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7858.284211] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7858.284218] VID/PID = 1286/204E, Boot2 version = 3201
[ 7858.284221] woal_usb_probe: invalid endpoint assignment
[ 7858.284266] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7858.284268] VID/PID = 1286/204E, Boot2 version = 3201
[ 7858.284269] woal_usb_probe: invalid endpoint assignment
[ 7858.285310] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7858.285312] VID/PID = 1286/204E, Boot2 version = 3201
[ 7858.285321] Attach moal handle ops, card interface type: 0x404
[ 7858.285326] No module param cfg file specified
[ 7858.285331] rx_work=1 cpu_num=18
[ 7858.285349] Attach mlan adapter operations.card_type is 0x404.
[ 7858.292184] WLAN FW is active
[ 7858.292192] on_time is 7858528016605
[ 7858.335023] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7858.335033] max_p2p_conn = 8, max_sta_conn = 8
[ 7858.343056] wlan: uap0 set max_mtu 2000
[ 7858.350375] wlan: version = USB8997---16.68.1.p183-MM5X16344.p3-GPL-(FP92) 
[ 7858.366402] usb 3-5 wlx9c50d1e343a4: renamed from uap0
[ 7858.426692] wlan: Stoping AP
[ 7858.426702] wlan: AP stopped
[ 7858.524685] wlan: wlx9c50d1e343a4 START SCAN
[ 7858.528537] Card is removed: -71
[ 7858.528570] usb 3-5: USB disconnect, device number 117
[ 7858.528599] Card is removed: -71
[ 7858.528720] Card is removed: -71
[ 7858.528843] Card is removed: -71
[ 7858.528879] Card is removed: -108
[ 7858.528920] Card is removed: -108
[ 7858.528958] Card is removed: -108
[ 7858.529001] IOCTL failed: 0000000063fb53b5 id=0x10000, sub_id=0x10003 action=1, status_code=0x80000007
[ 7858.600194] USB: unregister device
[ 7858.648301] Free module params
[ 7858.924189] usb 3-5: new high-speed USB device number 118 using xhci_hcd
[ 7859.080612] usb 3-5: New USB device found, idVendor=1286, idProduct=2052, bcdDevice=40.00
[ 7859.080619] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7859.080621] usb 3-5: Product: Marvell Wireless Device
[ 7859.080623] usb 3-5: Manufacturer: Marvell
[ 7859.080624] usb 3-5: SerialNumber: 0000000000000000
[ 7859.081527] USB probe: idVendor=1286 idProduct=2052 bInterfaceNumber=0
[ 7859.081532] VID/PID = 1286/2052, Boot2 version = 4000
[ 7859.081542] Attach moal handle ops, card interface type: 0x404
[ 7859.081546] No module param cfg file specified
[ 7859.081550] rx_work=1 cpu_num=18
[ 7859.081567] Attach mlan adapter operations.card_type is 0x404.
[ 7859.088188] Request firmware: mrvl/usbusb8997_combo_v4.bin
[ 7859.479488] fw_dnld: 610252 bytes downloaded
[ 7860.228199] usb 3-5: USB disconnect, device number 118
[ 7860.248191] USB: unregister device
[ 7860.248211] Free module params
[ 7860.532189] usb 3-5: new high-speed USB device number 119 using xhci_hcd
[ 7861.156216] usb 3-5: device descriptor read/64, error -71
[ 7861.430326] usb 3-5: New USB device found, idVendor=1286, idProduct=204e, bcdDevice=32.01
[ 7861.430333] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7861.430336] usb 3-5: Product: Bluetooth and Wireless LAN Composite Device
[ 7861.430337] usb 3-5: Manufacturer: Marvell
[ 7861.430339] usb 3-5: SerialNumber: 9C50D1E343A4
[ 7861.436256] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7861.436261] VID/PID = 1286/204E, Boot2 version = 3201
[ 7861.436263] woal_usb_probe: invalid endpoint assignment
[ 7861.436305] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7861.436306] VID/PID = 1286/204E, Boot2 version = 3201
[ 7861.436308] woal_usb_probe: invalid endpoint assignment
[ 7861.437315] USB probe: idVendor=1286 idProduct=204e bInterfaceNumber=0
[ 7861.437317] VID/PID = 1286/204E, Boot2 version = 3201
[ 7861.437325] Attach moal handle ops, card interface type: 0x404
[ 7861.437330] No module param cfg file specified
[ 7861.437334] rx_work=1 cpu_num=18
[ 7861.437351] Attach mlan adapter operations.card_type is 0x404.
[ 7861.440202] WLAN FW is active
[ 7861.440206] on_time is 7861676026895
[ 7861.483523] fw_cap_info=0x187cffa3, dev_cap_mask=0xffffffff
[ 7861.483534] max_p2p_conn = 8, max_sta_conn = 8
[ 7861.491566] wlan: uap0 set max_mtu 2000
[ 7861.498547] Card is removed: -71
[ 7861.498663] Card is removed: -71
[ 7861.498785] Card is removed: -71
[ 7861.498904] Card is removed: -71
[ 7861.499024] Card is removed: -71
[ 7861.499142] Card is removed: -71
[ 7861.499351] Card is removed: -71