U-Boot dub-2020.04-r3.1+g749d901 (Sep 15 2021 - 08:31:24 +0000) CPU: NXP i.MX8QXP RevC A35 at 1200 MHz at 38C DRAM: 2 GiB MCA: HW_VER=1 FW_VER=0.18 MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Model: Digi International ConnectCore 8X SBC Express Board. ConnectCore 8X SOM variant 0x02: 2 GiB LPDDR4, Wi-Fi, Bluetooth, MCA, Crypto-auth Board version undefined, ID 129 Boot: MMC0 BuildInfo: - SCFW 11102b55, SECO-FW 640b5efb, IMX-MKIMAGE 8947fea3, ATF f1d7187 - U-Boot dub-2020.04-r3.1+g749d901 flash target is MMC:0 Net: eth0: ethernet@5b040000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 gpio: pin 148 (gpio 148) value is 0 2775 bytes read in 12 ms (225.6 KiB/s) ## Executing script at 88280000 Setting 10 inch display DT ## Loading kernel: Image.gz-ccimx8x-sbc-express.bin 9931025 bytes read in 243 ms (39 MiB/s) ## Loading device tree file in variable 'fdt_file': ccimx8x-sbc-express-id129-disp-10.dtb 122324 bytes read in 15 ms (7.8 MiB/s) ## Applying device tree overlays in variable 'overlays': 2791 bytes read in 12 ms (226.6 KiB/s) -> _ov_som_quad_ccimx8x.dtbo SOM: quad-core CPU 808 bytes read in 8 ms (98.6 KiB/s) -> _ov_som_wifi_ccimx8x.dtbo SOM: Wi-Fi 712 bytes read in 8 ms (86.9 KiB/s) -> _ov_som_bt_ccimx8x.dtbo SOM: Bluetooth ## Flattened Device Tree blob at 8a000000 Booting using the fdt blob at 0x8a000000 Using Device Tree in place at 000000008a000000, end 000000008a021fff Disable clock-controller@5a4d0000 rsrc 62 not owned Disable clock-controller@5ac90000 rsrc 102 not owned Disable clock-controller@5b260000 rsrc 253 not owned Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd042] [ 0.000000] Linux version 5.4.84-dey+g6f752f9 (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Tue Sep 14 16:03:33 UTC 2021 [ 0.000000] Machine model: Digi International ConnectCore 8X SBC Express. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000096000000, size 960 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xffba7800-0xffba8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000086200000-0x0000000091ffffff] [ 0.000000] node 0: [mem 0x0000000094c00000-0x00000000ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57880 r8192 d32232 u98304 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 495624 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: console=ttyLP2,115200 root=PARTUUID=1c606ef5-f1ac-43b9-9bb5-d5c578580b6b rootwait rw fbcon=logo-pos:center [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 860440K/2015232K available (14524K kernel code, 1054K rwdata, 4640K rodata, 2496K init, 994K bss, 171752K reserved, 983040K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 512 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000051b00000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x44c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000005] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000937] Console: colour dummy device 80x25 [ 0.001029] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.001041] pid_max: default: 32768 minimum: 301 [ 0.001136] LSM: Security Framework initializing [ 0.001207] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001223] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002688] ASID allocator initialised with 32768 entries [ 0.002777] rcu: Hierarchical SRCU implementation. [ 0.005517] EFI services will not be available. [ 0.005807] smp: Bringing up secondary CPUs ... [ 0.006503] Detected VIPT I-cache on CPU1 [ 0.006534] GICv3: CPU1: found redistributor 3 region 0:0x0000000051b60000 [ 0.006576] CPU1: Booted secondary processor 0x0000000003 [0x410fd042] [ 0.007287] Detected VIPT I-cache on CPU2 [ 0.007308] GICv3: CPU2: found redistributor 2 region 0:0x0000000051b40000 [ 0.007331] CPU2: Booted secondary processor 0x0000000002 [0x410fd042] [ 0.007998] Detected VIPT I-cache on CPU3 [ 0.008016] GICv3: CPU3: found redistributor 1 region 0:0x0000000051b20000 [ 0.008037] CPU3: Booted secondary processor 0x0000000001 [0x410fd042] [ 0.008101] smp: Brought up 1 node, 4 CPUs [ 0.008129] SMP: Total of 4 processors activated. [ 0.008136] CPU features: detected: 32-bit EL0 Support [ 0.008142] CPU features: detected: CRC32 instructions [ 0.014624] CPU: All CPU(s) started at EL2 [ 0.014664] alternatives: patching kernel code [ 0.015869] devtmpfs: initialized [ 0.033763] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.033785] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.063307] pinctrl core: initialized pinctrl subsystem [ 0.064614] DMI not present or invalid. [ 0.064944] NET: Registered protocol family 16 [ 0.066582] DMA: preallocated 256 KiB pool for atomic allocations [ 0.066600] audit: initializing netlink subsys (disabled) [ 0.066758] audit: type=2000 audit(0.064:1): state=initialized audit_enabled=0 res=1 [ 0.068036] cpuidle: using governor menu [ 0.069080] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.071150] Serial: AMBA PL011 UART driver [ 0.071231] imx mu driver is registered. [ 0.129442] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.129456] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.129463] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.129472] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.131875] cryptd: max_cpu_qlen set to 1000 [ 0.138241] ACPI: Interpreter disabled. [ 0.138922] iommu: Default domain type: Translated [ 0.139131] vgaarb: loaded [ 0.139480] SCSI subsystem initialized [ 0.139963] usbcore: registered new interface driver usbfs [ 0.140012] usbcore: registered new interface driver hub [ 0.140081] usbcore: registered new device driver usb [ 0.141830] mc: Linux media interface: v0.10 [ 0.141863] videodev: Linux video capture interface: v2.00 [ 0.141895] pps_core: LinuxPPS API ver. 1 registered [ 0.141903] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.141919] PTP clock support registered [ 0.143391] No BMan portals available! [ 0.143772] QMan: Allocated lookup table at (____ptrval____), entry count 65537 [ 0.144644] No QMan portals available! [ 0.145770] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree [ 0.147952] Advanced Linux Sound Architecture Driver Initialized. [ 0.148929] Bluetooth: Core ver 2.22 [ 0.148972] NET: Registered protocol family 31 [ 0.148978] Bluetooth: HCI device and connection manager initialized [ 0.148989] Bluetooth: HCI socket layer initialized [ 0.148999] Bluetooth: L2CAP socket layer initialized [ 0.149017] Bluetooth: SCO socket layer initialized [ 0.150312] imx-scu scu: NXP i.MX SCU Initialized [ 0.156080] random: fast init done [ 0.188991] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/hoggrp [ 0.189013] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/lpuart0grp_2wires [ 0.189063] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/flexcan0grp [ 0.189075] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/flexcan1grp [ 0.189134] imx8qxp-pinctrl scu:pinctrl: initialized IMX pinctrl driver [ 0.190926] clocksource: Switched to clocksource arch_sys_counter [ 0.191241] VFS: Disk quotas dquot_6.6.0 [ 0.191303] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.191498] pnp: PnP ACPI: disabled [ 0.220520] thermal_sys: Registered thermal governor 'step_wise' [ 0.220525] thermal_sys: Registered thermal governor 'power_allocator' [ 0.221077] NET: Registered protocol family 2 [ 0.221506] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.221542] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.221668] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.221926] TCP: Hash tables configured (established 16384 bind 16384) [ 0.222056] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.222104] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.222282] NET: Registered protocol family 1 [ 0.222947] RPC: Registered named UNIX socket transport module. [ 0.222956] RPC: Registered udp transport module. [ 0.222961] RPC: Registered tcp transport module. [ 0.222966] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.223466] PCI: CLS 0 bytes, default 64 [ 0.224264] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.225473] kvm [1]: IPA Size Limit: 40bits [ 0.226028] kvm [1]: GICv3: no GICV resource entry [ 0.226034] kvm [1]: disabling GICv2 emulation [ 0.226056] kvm [1]: GIC system register CPU interface enabled [ 0.226145] kvm [1]: vgic interrupt IRQ1 [ 0.226256] kvm [1]: Hyp mode initialized successfully [ 0.230273] Initialise system trusted keyrings [ 0.230425] workingset: timestamp_bits=44 max_order=19 bucket_order=0 [ 0.238699] NFS: Registering the id_resolver key type [ 0.238729] Key type id_resolver registered [ 0.238735] Key type id_legacy registered [ 0.238747] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.239072] 9p: Installing v9fs 9p2000 file system support [ 0.255312] NET: Registered protocol family 38 [ 0.255323] Key type asymmetric registered [ 0.255330] Asymmetric key parser 'x509' registered [ 0.255378] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.255385] io scheduler mq-deadline registered [ 0.255391] io scheduler kyber registered [ 0.278202] LDO2: Bringing 3300000uV into 1800000-1800000uV [ 0.279669] pf8x00-sc pf8x00-sc: PF8X00 pmic driver loaded (40|31|20|0c) [ 0.281293] pwm-backlight lvds_backlight@0: lvds_backlight@0 supply power not found, using dummy regulator [ 0.282453] EINJ: ACPI disabled. [ 0.283646] clock-hsio-refa: gpio_clk_driver_probe: Can't get 'enable' named GPIO property [ 0.283667] gpio-clk: probe of bus@5f000000:clock-hsio-refa failed with error -2 [ 0.283739] clock-hsio-refb: gpio_clk_driver_probe: Can't get 'enable' named GPIO property [ 0.283751] gpio-clk: probe of bus@5f000000:clock-hsio-refb failed with error -2 [ 0.288013] imx8qxp-lpcg-clk 37620000.clock-controller: failed to get clock parent names [ 0.288062] imx8qxp-lpcg-clk: probe of 37620000.clock-controller failed with error -22 [ 0.373933] mxs-dma 5b810000.dma-apbh: initialized [ 0.377432] Bus freq driver module loaded [ 0.383791] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.389125] 5a060000.serial: ttyLP0 at MMIO 0x5a060010 (irq = 54, base_baud = 5000000) is a FSL_LPUART [ 0.389485] fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA [ 0.389496] fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA [ 0.390039] 5a070000.serial: ttyLP1 at MMIO 0x5a070010 (irq = 55, base_baud = 5000000) is a FSL_LPUART [ 0.390859] 5a080000.serial: ttyLP2 at MMIO 0x5a080010 (irq = 56, base_baud = 5000000) is a FSL_LPUART [ 1.474763] printk: console [ttyLP2] enabled [ 1.480114] 5a090000.serial: ttyLP3 at MMIO 0x5a090010 (irq = 57, base_baud = 5000000) is a FSL_LPUART [ 1.554834] loop: module loaded [ 1.562067] imx ahci driver is registered. [ 1.569254] caam 31400000.crypto: device ID = 0x0a16040000000100 (Era 9) [ 1.576010] caam 31400000.crypto: job rings = 2, qi = 0 [ 1.593969] caam algorithms registered in /proc/crypto [ 1.600629] caam 31400000.crypto: caam pkc algorithms registered in /proc/crypto [ 1.608061] caam 31400000.crypto: registering rng-caam [ 1.613571] Device caam-keygen registered [ 1.624775] caam_keyblob caam-keyblob: caam keyblob initialized [ 1.635904] libphy: Fixed MDIO Bus: probed [ 1.641176] CAN device driver interface [ 1.652852] Freescale FM module, FMD API version 21.1.0 [ 1.659052] Freescale FM Ports module [ 1.662741] fsl_mac: fsl_mac: FSL FMan MAC API based driver [ 1.668870] fsl_dpa: FSL DPAA Ethernet driver [ 1.673609] fsl_advanced: FSL DPAA Advanced drivers: [ 1.678587] fsl_proxy: FSL DPAA Proxy initialization driver [ 1.684542] fsl_oh: FSL FMan Offline Parsing port driver [ 1.691048] sky2: driver version 1.30 [ 1.696433] PPP generic driver version 2.4.2 [ 1.700931] PPP BSD Compression module registered [ 1.705658] PPP Deflate Compression module registered [ 1.710809] random: crng init done [ 1.711065] VFIO - User Level meta-driver version: 0.3 [ 1.725473] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.732025] ehci-pci: EHCI PCI platform driver [ 1.736546] ehci-platform: EHCI generic platform driver [ 1.742468] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.748700] ohci-pci: OHCI PCI platform driver [ 1.753231] ohci-platform: OHCI generic platform driver [ 1.760554] usbcore: registered new interface driver cdc_acm [ 1.766230] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.774299] usbcore: registered new interface driver usb-storage [ 1.780398] usbcore: registered new interface driver usbserial_generic [ 1.787050] usbserial: USB Serial support registered for generic [ 1.793108] usbcore: registered new interface driver option [ 1.798711] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.805730] usbcore: registered new interface driver qcserial [ 1.811511] usbserial: USB Serial support registered for Qualcomm USB modem [ 1.818507] usbcore: registered new interface driver sierra [ 1.824112] usbserial: USB Serial support registered for Sierra USB modem [ 1.830949] usbcore: registered new interface driver usb_ehset_test [ 1.844911] input: sc-powerkey as /devices/platform/sc-powerkey/input/input0 [ 1.856424] i2c /dev entries driver [ 1.867127] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 1.875601] Bluetooth: HCI UART driver ver 2.3 [ 1.880059] Bluetooth: HCI UART protocol H4 registered [ 1.891821] sdhci: Secure Digital Host Controller Interface driver [ 1.898089] sdhci: Copyright(c) Pierre Ossman [ 1.903194] Synopsys Designware Multimedia Card Interface Driver [ 1.911344] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.918874] mmc0: CQHCI version 5.10 [ 1.953941] mmc0: SDHCI controller on 5b010000.mmc [5b010000.mmc] using ADMA [ 1.962203] mmc1: CQHCI version 5.10 [ 1.966193] sdhci-esdhc-imx 5b020000.mmc: could not get ultra high speed state, work on normal mode [ 1.979061] ledtrig-cpu: registered to indicate activity on CPUs [ 1.987659] usbcore: registered new interface driver usbhid [ 1.993287] usbhid: USB HID core driver [ 1.997700] mxc-md bus@58000000:camera: deferring cap_device device registration [ 2.006349] mxc-isi 58100000.isi: mxc_isi.0 registered successfully [ 2.012930] mxc-isi 58110000.isi: mxc_isi.1 registered successfully [ 2.019506] mxc-isi 58120000.isi: mxc_isi.2 registered successfully [ 2.026175] mxc-isi 58130000.isi: mxc_isi.3 registered successfully [ 2.036767] No fsl,qman node [ 2.039691] Freescale USDPAA process driver [ 2.043923] fsl-usdpaa: no region found [ 2.047800] Freescale USDPAA process IRQ driver [ 2.065354] Galcore version 6.4.3.p1.305572 [ 2.107540] mmc0: Command Queue Engine enabled [ 2.112048] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 2.119573] mmcblk0: mmc0:0001 HAG4a2 14.7 GiB [ 2.124348] mmcblk0boot0: mmc0:0001 HAG4a2 partition 1 8.00 MiB [ 2.130545] mmcblk0boot1: mmc0:0001 HAG4a2 partition 2 8.00 MiB [ 2.136784] mmcblk0rpmb: mmc0:0001 HAG4a2 partition 3 4.00 MiB, chardev (242:0) [ 2.147087] mmcblk0: p1 p2 p3 p4 p5 p6 p7 [ 2.165183] [drm] Initialized vivante 1.0.0 20170808 for 80000000.imx8_gpu0_ss on minor 0 [ 2.176991] [VPU Decoder] warning: init rtx channel failed, ret: -517 [ 2.183507] [VPU Decoder] failed to request mailbox, ret = -517 [ 2.195339] [VPU Encoder] warning: init rtx channel failed, ret: -517 [ 2.201922] [VPU Encoder] fail to request mailbox, ret = -517 [ 2.216592] fsl-sai 59050000.sai: Unbalanced pm_runtime_enable! [ 2.227397] NET: Registered protocol family 26 [ 2.232571] NET: Registered protocol family 10 [ 2.237802] Segment Routing with IPv6 [ 2.241561] NET: Registered protocol family 17 [ 2.246052] can: controller area network core (rev 20170425 abi 9) [ 2.252310] NET: Registered protocol family 29 [ 2.256844] can: raw protocol (rev 20170425) [ 2.261129] can: broadcast manager protocol (rev 20170425 t) [ 2.266824] can: netlink gateway (rev 20190810) max_hops=1 [ 2.272607] Bluetooth: RFCOMM TTY layer initialized [ 2.277502] Bluetooth: RFCOMM socket layer initialized [ 2.282691] Bluetooth: RFCOMM ver 1.11 [ 2.286479] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.291802] Bluetooth: BNEP filters: protocol multicast [ 2.297057] Bluetooth: BNEP socket layer initialized [ 2.302038] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.307989] Bluetooth: HIDP socket layer initialized [ 2.313009] 8021q: 802.1Q VLAN Support v1.8 [ 2.317230] lib80211: common routines for IEEE802.11 drivers [ 2.323060] 9pnet: Installing 9P2000 support [ 2.327399] Key type dns_resolver registered [ 2.331968] batman_adv: B.A.T.M.A.N. advanced 2019.4 (compatibility version 15) loaded [ 2.340346] registered taskstats version 1 [ 2.344463] Loading compiled-in X.509 certificates [ 2.374528] mxs_phy 5b100000.usbphy: 5b100000.usbphy supply phy-3p0 not found, using dummy regulator [ 2.396418] 3v3_rf: supplied by 3v3 [ 2.400353] rf_wl_en: supplied by 3v3_rf [ 2.404685] rf_bt_en: supplied by 3v3_rf [ 2.409240] usb_phy_generic bus@5b000000:usb3-phy: bus@5b000000:usb3-phy supply vcc not found, using dummy regulator [ 2.420439] gpio-104 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 2.429432] imx-lpi2c 5a800000.i2c: using scl,sda for recovery [ 2.443648] mca-rtc mca-cc8x-rtc: registered as rtc0 [ 2.454610] Watchdog driver for MCA (timeout=30 sec, nowayout=1, reset (full)) [ 2.476434] input: mca-cc8x-pwrkey as /devices/platform/bus@5a000000/5a800000.i2c/i2c-0/0-0063/mca-cc8x-pwrkey/input/input1 [ 2.489219] ADC driver for MCA [ 2.492959] Tamper driver for MCA [ 2.496980] mca-uart: probe of mca-cc8x-uart failed with error -22 [ 2.503877] mca-pwm mca-pwm: registered PWM chip (tpm: 0, channels: 6) [ 2.510477] mca-pwm mca-pwm: registered PWM chip (tpm: 1, channels: 2) [ 2.517079] mca-pwm mca-pwm: registered PWM chip (tpm: 2, channels: 2) [ 2.525013] i2c i2c-0: LPI2C adapter registered [ 2.530118] imx-lpi2c 5a820000.i2c: can't get I2C ipg clock [ 2.535761] imx-lpi2c: probe of 5a820000.i2c failed with error -2 [ 2.545958] tlv320aic31xx-codec 3-0018: 3-0018 supply HPVDD not found, using dummy regulator [ 2.554509] tlv320aic31xx-codec 3-0018: 3-0018 supply SPRVDD not found, using dummy regulator [ 2.563090] tlv320aic31xx-codec 3-0018: 3-0018 supply SPLVDD not found, using dummy regulator [ 2.571674] tlv320aic31xx-codec 3-0018: 3-0018 supply AVDD not found, using dummy regulator [ 2.580081] tlv320aic31xx-codec 3-0018: 3-0018 supply IOVDD not found, using dummy regulator [ 2.588577] tlv320aic31xx-codec 3-0018: 3-0018 supply DVDD not found, using dummy regulator [ 2.597097] i2c i2c-3: LPI2C adapter registered [ 2.602678] imx-lpi2c 56226000.i2c: can't get irq number [ 2.611748] pwm-backlight lvds_backlight@0: lvds_backlight@0 supply power not found, using dummy regulator [ 2.612198] imx6q-pcie 5f010000.pcie: No cache used with register defaults set! [ 2.626436] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.635432] [drm] No driver support for vblank timestamp query. [ 2.641440] imx-drm display-subsystem: bound imx-drm-dpu-bliteng.2 (ops 0xffff800010f6c9a0) [ 2.650516] imx-drm display-subsystem: bound imx-dpu-crtc.0 (ops 0xffff800010f6c668) [ 2.658837] imx-drm display-subsystem: bound imx-dpu-crtc.1 (ops 0xffff800010f6c668) [ 2.667506] dpu-core 56180000.dpu: driver probed [ 2.743259] pps pps0: new PPS source ptp0 [ 2.749892] libphy: fec_enet_mii_bus: probed [ 2.756209] fec 5b040000.ethernet eth0: registered PHC device 0 [ 2.762959] imx6q-pcie 5f010000.pcie: PCIe PLL locked after 0 us. [ 2.766515] xhci-cdns3: xHCI Host Controller [ 2.769129] imx6q-pcie 5f010000.pcie: host bridge /bus@5f000000/pcie@0x5f010000 ranges: [ 2.773463] xhci-cdns3: new USB bus registered, assigned bus number 1 [ 2.781508] imx6q-pcie 5f010000.pcie: IO 0x7ff80000..0x7ff8ffff -> 0x00000000 [ 2.789382] xhci-cdns3: hcc params 0x200073c8 hci version 0x100 quirks 0x0000001000018010 [ 2.795450] imx6q-pcie 5f010000.pcie: MEM 0x70000000..0x7fefffff -> 0x70000000 [ 2.804510] hub 1-0:1.0: USB hub found [ 2.814874] hub 1-0:1.0: 1 port detected [ 2.819110] xhci-cdns3: xHCI Host Controller [ 2.823490] xhci-cdns3: new USB bus registered, assigned bus number 2 [ 2.830036] xhci-cdns3: Host supports USB 3.0 SuperSpeed [ 2.835512] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.844117] hub 2-0:1.0: USB hub found [ 2.847905] hub 2-0:1.0: 1 port detected [ 2.853495] imx_usb 5b0d0000.usb: 5b0d0000.usb supply vbus not found, using dummy regulator [ 2.865447] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 2.870361] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 3 [ 2.890966] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 2.897404] hub 3-0:1.0: USB hub found [ 2.901213] hub 3-0:1.0: 1 port detected [ 2.907979] mmc1: CQHCI version 5.10 [ 2.911217] imx6q-pcie 5f010000.pcie: Link up [ 2.911585] sdhci-esdhc-imx 5b020000.mmc: could not get ultra high speed state, work on normal mode [ 2.915933] imx6q-pcie 5f010000.pcie: Link up [ 2.925033] sdhci-esdhc-imx 5b020000.mmc: Got CD GPIO [ 2.929337] imx6q-pcie 5f010000.pcie: Link up, Gen1 [ 2.939412] imx6q-pcie 5f010000.pcie: PCI host bridge to bus 0000:00 [ 2.945810] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.951317] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.957530] pci_bus 0000:00: root bus resource [mem 0x70000000-0x7fefffff] [ 2.964441] pci 0000:00:00.0: [1957:0000] type 01 class 0x060400 [ 2.965865] mmc1: SDHCI controller on 5b020000.mmc [5b020000.mmc] using ADMA [ 2.970487] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 2.982466] mxc-md bus@58000000:camera: deferring cap_device device registration [ 2.983824] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x00ffffff pref] [ 2.998027] pci 0000:00:00.0: supports D1 D2 [ 3.002335] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.014508] pci 0000:01:00.0: [168c:003e] type 00 class 0x028000 [ 3.020656] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 3.022751] tlv320aic31xx-codec 3-0018: ASoC: sink widget SPK ClassD overwritten [ 3.027839] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.034997] tlv320aic31xx-codec 3-0018: ASoC: source widget SPK ClassD overwritten [ 3.048647] debugfs: Directory '59050000.sai' with parent 'imx8-tlv320' already present! [ 3.056673] pci 0000:00:00.0: BAR 0: assigned [mem 0x70000000-0x70ffffff] [ 3.056933] asoc-simple-card sound: tlv320dac31xx-hifi <-> 59050000.sai mapping ok [ 3.063559] pci 0000:00:00.0: BAR 6: assigned [mem 0x71000000-0x71ffffff pref] [ 3.071219] asoc-simple-card sound: ASoC: no DMI vendor name! [ 3.078378] pci 0000:00:00.0: BAR 14: assigned [mem 0x72000000-0x721fffff] [ 3.088761] gpio-57 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 3.091065] pci 0000:01:00.0: BAR 0: assigned [mem 0x72000000-0x721fffff 64bit] [ 3.099942] imx-lpi2c 56226000.i2c: using scl,sda for recovery [ 3.107292] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.113718] Goodix-TS 16-0014: No vin supply [ 3.118304] pci 0000:00:00.0: bridge window [mem 0x72000000-0x721fffff] [ 3.118678] pcieport 0000:00:00.0: PME: Signaling with IRQ 447 [ 3.154964] usb 1-1: new full-speed USB device number 2 using cdns-usb3 [ 3.179101] Goodix-TS 16-0014: i2c test failed attempt 1: -5 [ 3.211067] Goodix-TS 16-0014: i2c test failed attempt 2: -5 [ 3.242960] Goodix-TS 16-0014: I2C communication failure: -5 [ 3.248676] Goodix-TS: probe of 16-0014 failed with error -5 [ 3.254712] Goodix-TS 16-005d: No vin supply [ 3.311412] hid-generic 0003:7374:1289.0001: device has no listeners, quitting [ 3.319090] Goodix-TS 16-005d: i2c test failed attempt 1: -5 [ 3.323988] input: DATA MODUL easyTOUCH as /devices/platform/bus@5b000000/5b110000.usb3/xhci-cdns3/usb1/1-1/1-1:1.1/0003:7374:1289.0002/input/input2 [ 3.338251] hid-multitouch 0003:7374:1289.0002: input: USB HID v1.11 Device [DATA MODUL easyTOUCH] on usb-xhci-cdns3-1/input1 [ 3.350725] hid-generic 0003:7374:1289.0003: device has no listeners, quitting [ 3.351089] Goodix-TS 16-005d: i2c test failed attempt 2: -5 [ 3.390959] Goodix-TS 16-005d: I2C communication failure: -5 [ 3.396667] Goodix-TS: probe of 16-005d failed with error -5 [ 3.402428] i2c i2c-16: LPI2C adapter registered [ 3.407493] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.414134] [drm] No driver support for vblank timestamp query. [ 3.420157] imx-drm display-subsystem: bound imx-drm-dpu-bliteng.2 (ops 0xffff800010f6c9a0) [ 3.429162] imx-drm display-subsystem: bound imx-dpu-crtc.0 (ops 0xffff800010f6c668) [ 3.437175] imx-drm display-subsystem: bound imx-dpu-crtc.1 (ops 0xffff800010f6c668) [ 3.445527] imx-drm display-subsystem: bound bus@56220000:ldb@562210e0 (ops 0xffff800010f6c048) [ 3.454797] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 1 [ 3.562490] Console: switching to colour frame buffer device 160x50 [ 3.583048] imx-drm display-subsystem: fb0: imx-drmdrmfb frame buffer device [ 3.591335] mxc-md bus@58000000:camera: deferring cap_device device registration [ 3.600751] mxc-md bus@58000000:camera: deferring cap_device device registration [ 3.620315] mca-rtc mca-cc8x-rtc: setting system clock to 1970-02-19T03:03:37 UTC (4244617) [ 3.629918] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.638843] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.645518] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.654165] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 3.665713] ALSA device list: [ 3.668703] #0: imx8-tlv320 [ 3.708403] EXT4-fs (mmcblk0p3): 1 orphan inode deleted [ 3.713819] EXT4-fs (mmcblk0p3): recovery complete [ 3.722878] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 3.731189] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 3.737645] devtmpfs: mounted [ 3.741488] Freeing unused kernel memory: 2496K [ 3.746111] Run /sbin/init as init process [ 3.807139] systemd[1]: System time before build time, advancing clock. [ 3.826642] systemd[1]: systemd 243.2+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.849053] systemd[1]: Detected architecture arm64. Welcome to Digi Embedded Yocto 3.0-r4 (zeus)! [ 3.903465] systemd[1]: Set hostname to . [ 4.102790] systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly. [ 4.249622] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 4.262034] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 4.273521] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 4.296985] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.320811] systemd[1]: Created slice system-weston.slice. [ OK ] Created slice system-weston.slice. [ 4.345154] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Paths. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Syslog Socket. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Temporary Directory (/tmp)... Starting Create list of st…odes for the current kernel... Starting Starts Psplash Boot screen... Starting Journal Service... Starting Load Kernel Modules... t Starting Remount [R oo t 4a.n7d6 9K9e0r3n] elc ryFiplteod Seyvs: telomsa[i0nmg. .ou. -of-tree module taints kernel. . Sta[r t i n g4. [8066;116;3]9 mcurdyepvto Cdoelvd:p ldurig vaerll 1D.e10vi cleosa[e0dm.. . [ 4.804584] EXT4-fs (mmcblk0p3): re-mounted. Opts: (null) [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ 4.862422] audit: type=1701 audit(1626880932.048:2): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=343 comm="psplash" exe="/usr/bin/psplash.psplash-oven" sig=11 res=1 [ OK ] Started Journal Service. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta… nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ 5.015911] systemd-journald[326]: Received client request to flush runtime journal. Starting Apply Kernel Variables... [ 5.028919] systemd-journald[326]: File /var/log/journal/28215ff37a4e40b4ab25c58dd6fcf6fd/system.journal corrupted or uncleanly shut down, renaming and replacing. Starting Create Static Device Nodes in /dev... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Apply Kernel Variables. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started udev Coldplug all Devices. Starting udev Wait for Complete Device Initialization... [ 5.673819] mxc-md bus@58000000:camera: deferring cap_device device registration [ 5.712416] [VPU Encoder] enable mu for core[0] [ 5.725297] [VPU Encoder] vpu encoder core[0] firmware version is 1.3.0 [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen … backlight:lvds_backlight@0... [ 6.286757] qca65x4: Setting US wireless region [ OK ] Started Load/Save Screen B…of backlight:lvds_backlight@0. [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Found device /dev/mmcblk0p4. Starting File System Check on /dev/mmcblk0p4... [ OK ] Started File System Check on /dev/mmcblk0p4. [ OK ] Found device /dev/mmcblk0p7. Mounting /Oven... Mounting /mnt/update... [ 6.930854] ol_download_firmware: chip_id:0x5030000 board_id:0x0 Starting File System Check on /dev/mmcblk0p1... [ OK ] Mounted /Oven. [ OK ] Mounted /mnt/update. [ OK ] Started File System Check on /dev/mmcblk0p1. Mounting /mnt/linux... [ OK ] Mounted /mnt/linux. [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started udev Wait for Complete Device Initialization. [ OK ] Started Starts Psplash Boot screen. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Run foo hourly. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket. [ OK ] Listening on SWUpdate socket listener. [ OK ] Listening on sshd.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Save/Restore Sound Card State... Starting Initialization of the bluetooth chip... Starting Enable CAN interface... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Configuration for i.MX GPU (Former rc_gpu.S). Starting Interface initialization via ifupdown... Starting Packet Filtering Framework... Starting Network Time Service (one-shot ntpdate mode)... Starting System-wide sound service... [ OK ] Started User Space Regulatory Firmware Loading. Starting Service to restart rsyslog service hourly... Starting System Logging Service... [ OK ] Started User Space SDMA Firmware Loading. [ OK ] Started SWUpdate daemon. Starting Login Service... Starting XBee GPIOs initialization... [ OK ] Started System Logging Service. [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Enable CAN interface. [ OK ] Started Interface initialization via ifupdown. [ OK ] Started Packet Filtering Framework. [ OK ] Started Network Time Service (one-shot ntpdate mode). [ OK ] Reached target Network (Pre). [ OK ] Reached target Sound Card. Starting Connection service... Stopping System Logging Service... [ OK ] Started XBee GPIOs initialization. [ OK ] Started Connection service. [ OK ] Reached target Network. Starting Busybox HTTP daemon... Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Vsftpd ftp daemon. [ OK ] Started System-wide sound service. [ OK ] Started Busybox HTTP daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Target Communication Framework agent. [ OK ] Started Login Service. [ OK ] Started Getty on tty1. [ OK ] Started Getty on tty2. [ OK ] Started Serial Getty on ttyLP2. [ OK ] Reached target Login Prompts. Starting Hostname Service... Starting Weston Wayland Compositor (on tty7)... Starting WPA supplicant... [ OK ] Started Weston Wayland Compositor (on tty7). [ OK ] Started WPA supplicant. [ OK ] Created slice User Slice of UID 0. Starting User Runtime Directory /run/user/0... [ OK ] Started User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ OK ] Started Initialization of the bluetooth chip. [ OK ] Reached target Bluetooth. Starting Bluetooth service... [ OK ] Started Hostname Service. [ OK ] Started Bluetooth service. [ OK ] Started User Manager for UID 0. [ OK ] Started Session c1 of user root. [ OK ] Stopped System Logging Service. Starting System Logging Service... [ OK ] Started System Logging Service. [ OK ] Started Service to restart rsyslog service hourly. [ OK ] Reached target Multi-User System. [ OK ] Started Oven Advance Application. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. Digi Embedded Yocto 3.0-r4 ccimx8x-sbc-express ttyLP2 ccimx8x-sbc-express login: