U-Boot dub-2020.04-r3.1+g749d901 (Sep 15 2021 - 08:31:24 +0000) CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 40C DRAM: 2 GiB MCA: HW_VER=1 FW_VER=0.12 MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Model: Digi International ConnectCore 8X SBC Express Board. ConnectCore 8X SOM variant 0x02: Industrial QuadXPlus, 16GB eMMC, 2GB LPDDR4, -40/+85C, Wireless, Bluetooth Board version undefined, ID 129 Boot: MMC0 BuildInfo: - SCFW 11102b55, SECO-FW d63fdb21, IMX-MKIMAGE 8947fea3, ATF f1d7187 - U-Boot dub-2020.04-r3.1+g749d901 flash target is MMC:0 Net: eth0: ethernet@5b040000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 1 0 gpio: pin 148 (gpio 148) value is 1 2775 bytes read in 13 ms (208 KiB/s) ## Executing script at 88280000 Setting 7 inch display DT ## Loading kernel: Image.gz-ccimx8x-sbc-express.bin 9931025 bytes read in 242 ms (39.1 MiB/s) ## Loading device tree file in variable 'fdt_file': ccimx8x-sbc-express-id129-disp-7.dtb 122324 bytes read in 15 ms (7.8 MiB/s) ## Applying device tree overlays in variable 'overlays': 2791 bytes read in 12 ms (226.6 KiB/s) -> _ov_som_quad_ccimx8x.dtbo SOM: quad-core CPU 712 bytes read in 8 ms (86.9 KiB/s) -> _ov_som_bt_ccimx8x.dtbo SOM: Bluetooth 808 bytes read in 7 ms (112.3 KiB/s) -> _ov_som_wifi_ccimx8x.dtbo SOM: Wi-Fi ## Flattened Device Tree blob at 8a000000 Booting using the fdt blob at 0x8a000000 Using Device Tree in place at 000000008a000000, end 000000008a021fff Disable clock-controller@5a4d0000 rsrc 62 not owned Disable clock-controller@5ac90000 rsrc 102 not owned Disable clock-controller@5b260000 rsrc 253 not owned Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd042] [ 0.000000] Linux version 5.4.84-dey+g6f752f9 (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Tue Sep 14 16:03:33 UTC 2021 [ 0.000000] Machine model: Digi International ConnectCore 8X SBC Express. [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000096000000, size 960 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xffba8800-0xffba9fff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000086200000-0x0000000091ffffff] [ 0.000000] node 0: [mem 0x0000000094c00000-0x00000000ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x00000000ffffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s57880 r8192 d32232 u98304 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 495624 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: console=ttyLP2,115200 root=PARTUUID=1c606ef5-f1ac-43b9-9bb5-d5c578580b6b rootwait rw fbcon=logo-pos:center [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 860444K/2015232K available (14524K kernel code, 1054K rwdata, 4640K rodata, 2496K init, 994K bss, 171748K reserved, 983040K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 512 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000051b00000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x44c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000005] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000938] Console: colour dummy device 80x25 [ 0.001036] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.001048] pid_max: default: 32768 minimum: 301 [ 0.001145] LSM: Security Framework initializing [ 0.001214] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001229] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002715] ASID allocator initialised with 32768 entries [ 0.002804] rcu: Hierarchical SRCU implementation. [ 0.005585] EFI services will not be available. [ 0.005881] smp: Bringing up secondary CPUs ... [ 0.006589] Detected VIPT I-cache on CPU1 [ 0.006620] GICv3: CPU1: found redistributor 3 region 0:0x0000000051b60000 [ 0.006662] CPU1: Booted secondary processor 0x0000000003 [0x410fd042] [ 0.007379] Detected VIPT I-cache on CPU2 [ 0.007401] GICv3: CPU2: found redistributor 2 region 0:0x0000000051b40000 [ 0.007423] CPU2: Booted secondary processor 0x0000000002 [0x410fd042] [ 0.008081] Detected VIPT I-cache on CPU3 [ 0.008099] GICv3: CPU3: found redistributor 1 region 0:0x0000000051b20000 [ 0.008120] CPU3: Booted secondary processor 0x0000000001 [0x410fd042] [ 0.008186] smp: Brought up 1 node, 4 CPUs [ 0.008214] SMP: Total of 4 processors activated. [ 0.008221] CPU features: detected: 32-bit EL0 Support [ 0.008229] CPU features: detected: CRC32 instructions [ 0.014758] CPU: All CPU(s) started at EL2 [ 0.014801] alternatives: patching kernel code [ 0.016021] devtmpfs: initialized [ 0.033983] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.034006] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.063729] pinctrl core: initialized pinctrl subsystem [ 0.065063] DMI not present or invalid. [ 0.065397] NET: Registered protocol family 16 [ 0.067065] DMA: preallocated 256 KiB pool for atomic allocations [ 0.067084] audit: initializing netlink subsys (disabled) [ 0.067247] audit: type=2000 audit(0.064:1): state=initialized audit_enabled=0 res=1 [ 0.068560] cpuidle: using governor menu [ 0.069598] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.071689] Serial: AMBA PL011 UART driver [ 0.071773] imx mu driver is registered. [ 0.129008] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.129023] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.129030] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.129040] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.131441] cryptd: max_cpu_qlen set to 1000 [ 0.137792] ACPI: Interpreter disabled. [ 0.138483] iommu: Default domain type: Translated [ 0.138676] vgaarb: loaded [ 0.139074] SCSI subsystem initialized [ 0.139547] usbcore: registered new interface driver usbfs [ 0.139596] usbcore: registered new interface driver hub [ 0.139662] usbcore: registered new device driver usb [ 0.141432] mc: Linux media interface: v0.10 [ 0.141467] videodev: Linux video capture interface: v2.00 [ 0.141496] pps_core: LinuxPPS API ver. 1 registered [ 0.141502] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.141524] PTP clock support registered [ 0.143065] No BMan portals available! [ 0.143479] QMan: Allocated lookup table at (____ptrval____), entry count 65537 [ 0.144458] No QMan portals available! [ 0.145603] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree [ 0.147797] Advanced Linux Sound Architecture Driver Initialized. [ 0.148753] Bluetooth: Core ver 2.22 [ 0.148795] NET: Registered protocol family 31 [ 0.148800] Bluetooth: HCI device and connection manager initialized [ 0.148815] Bluetooth: HCI socket layer initialized [ 0.148823] Bluetooth: L2CAP socket layer initialized [ 0.148841] Bluetooth: SCO socket layer initialized [ 0.150109] imx-scu scu: NXP i.MX SCU Initialized [ 0.155942] random: fast init done [ 0.194240] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/hoggrp [ 0.194262] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/lpuart0grp_2wires [ 0.194312] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/flexcan0grp [ 0.194323] imx8qxp-pinctrl scu:pinctrl: Invalid fsl,pins or pins property in node /scu/pinctrl/flexcan1grp [ 0.194383] imx8qxp-pinctrl scu:pinctrl: initialized IMX pinctrl driver [ 0.196255] clocksource: Switched to clocksource arch_sys_counter [ 0.196503] VFS: Disk quotas dquot_6.6.0 [ 0.196565] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.196771] pnp: PnP ACPI: disabled [ 0.226060] thermal_sys: Registered thermal governor 'step_wise' [ 0.226065] thermal_sys: Registered thermal governor 'power_allocator' [ 0.226631] NET: Registered protocol family 2 [ 0.227059] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.227094] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.227218] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.227469] TCP: Hash tables configured (established 16384 bind 16384) [ 0.227576] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.227623] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.227790] NET: Registered protocol family 1 [ 0.228204] RPC: Registered named UNIX socket transport module. [ 0.228211] RPC: Registered udp transport module. [ 0.228216] RPC: Registered tcp transport module. [ 0.228221] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.228718] PCI: CLS 0 bytes, default 64 [ 0.229517] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.230734] kvm [1]: IPA Size Limit: 40bits [ 0.231315] kvm [1]: GICv3: no GICV resource entry [ 0.231324] kvm [1]: disabling GICv2 emulation [ 0.231345] kvm [1]: GIC system register CPU interface enabled [ 0.231434] kvm [1]: vgic interrupt IRQ1 [ 0.231558] kvm [1]: Hyp mode initialized successfully [ 0.235434] Initialise system trusted keyrings [ 0.235568] workingset: timestamp_bits=44 max_order=19 bucket_order=0 [ 0.243817] NFS: Registering the id_resolver key type [ 0.243851] Key type id_resolver registered [ 0.243857] Key type id_legacy registered [ 0.243870] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.244069] 9p: Installing v9fs 9p2000 file system support [ 0.261240] NET: Registered protocol family 38 [ 0.261252] Key type asymmetric registered [ 0.261259] Asymmetric key parser 'x509' registered [ 0.261299] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.261306] io scheduler mq-deadline registered [ 0.261312] io scheduler kyber registered [ 0.287951] LDO2: Bringing 3300000uV into 1800000-1800000uV [ 0.289616] pf8x00-sc pf8x00-sc: PF8X00 pmic driver loaded (40|20|20|0c) [ 0.291240] pwm-backlight lvds_backlight@0: lvds_backlight@0 supply power not found, using dummy regulator [ 0.292506] EINJ: ACPI disabled. [ 0.293663] clock-hsio-refa: gpio_clk_driver_probe: Can't get 'enable' named GPIO property [ 0.293683] gpio-clk: probe of bus@5f000000:clock-hsio-refa failed with error -2 [ 0.293756] clock-hsio-refb: gpio_clk_driver_probe: Can't get 'enable' named GPIO property [ 0.293768] gpio-clk: probe of bus@5f000000:clock-hsio-refb failed with error -2 [ 0.298080] imx8qxp-lpcg-clk 37620000.clock-controller: failed to get clock parent names [ 0.298166] imx8qxp-lpcg-clk: probe of 37620000.clock-controller failed with error -22 [ 0.383465] mxs-dma 5b810000.dma-apbh: initialized [ 0.386968] Bus freq driver module loaded [ 0.393385] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.398828] 5a060000.serial: ttyLP0 at MMIO 0x5a060010 (irq = 54, base_baud = 5000000) is a FSL_LPUART [ 0.399210] fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA [ 0.399221] fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA [ 0.399814] 5a070000.serial: ttyLP1 at MMIO 0x5a070010 (irq = 55, base_baud = 5000000) is a FSL_LPUART [ 0.400724] 5a080000.serial: ttyLP2 at MMIO 0x5a080010 (irq = 56, base_baud = 5000000) is a FSL_LPUART [ 1.485023] printk: console [ttyLP2] enabled [ 1.490331] 5a090000.serial: ttyLP3 at MMIO 0x5a090010 (irq = 57, base_baud = 5000000) is a FSL_LPUART [ 1.568584] loop: module loaded [ 1.575836] imx ahci driver is registered. [ 1.583038] caam 31400000.crypto: device ID = 0x0a16040000000100 (Era 9) [ 1.589794] caam 31400000.crypto: job rings = 2, qi = 0 [ 1.614908] caam algorithms registered in /proc/crypto [ 1.621570] caam 31400000.crypto: caam pkc algorithms registered in /proc/crypto [ 1.629007] caam 31400000.crypto: registering rng-caam [ 1.634494] Device caam-keygen registered [ 1.643623] random: crng init done [ 1.645511] caam_keyblob caam-keyblob: caam keyblob initialized [ 1.658231] libphy: Fixed MDIO Bus: probed [ 1.663578] CAN device driver interface [ 1.675523] Freescale FM module, FMD API version 21.1.0 [ 1.681727] Freescale FM Ports module [ 1.685406] fsl_mac: fsl_mac: FSL FMan MAC API based driver [ 1.691548] fsl_dpa: FSL DPAA Ethernet driver [ 1.696312] fsl_advanced: FSL DPAA Advanced drivers: [ 1.701291] fsl_proxy: FSL DPAA Proxy initialization driver [ 1.707261] fsl_oh: FSL FMan Offline Parsing port driver [ 1.713774] sky2: driver version 1.30 [ 1.719178] PPP generic driver version 2.4.2 [ 1.723686] PPP BSD Compression module registered [ 1.728440] PPP Deflate Compression module registered [ 1.733759] VFIO - User Level meta-driver version: 0.3 [ 1.744933] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.751497] ehci-pci: EHCI PCI platform driver [ 1.756024] ehci-platform: EHCI generic platform driver [ 1.761967] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.768189] ohci-pci: OHCI PCI platform driver [ 1.772703] ohci-platform: OHCI generic platform driver [ 1.780036] usbcore: registered new interface driver cdc_acm [ 1.785719] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.793784] usbcore: registered new interface driver usb-storage [ 1.799870] usbcore: registered new interface driver usbserial_generic [ 1.806501] usbserial: USB Serial support registered for generic [ 1.812559] usbcore: registered new interface driver option [ 1.818159] usbserial: USB Serial support registered for GSM modem (1-port) [ 1.825187] usbcore: registered new interface driver qcserial [ 1.830965] usbserial: USB Serial support registered for Qualcomm USB modem [ 1.837968] usbcore: registered new interface driver sierra [ 1.843569] usbserial: USB Serial support registered for Sierra USB modem [ 1.850400] usbcore: registered new interface driver usb_ehset_test [ 1.864415] input: sc-powerkey as /devices/platform/sc-powerkey/input/input0 [ 1.875914] i2c /dev entries driver [ 1.886696] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 1.895167] Bluetooth: HCI UART driver ver 2.3 [ 1.899619] Bluetooth: HCI UART protocol H4 registered [ 1.911370] sdhci: Secure Digital Host Controller Interface driver [ 1.917608] sdhci: Copyright(c) Pierre Ossman [ 1.922680] Synopsys Designware Multimedia Card Interface Driver [ 1.930836] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.938283] mmc0: CQHCI version 5.10 [ 1.973807] mmc0: SDHCI controller on 5b010000.mmc [5b010000.mmc] using ADMA [ 1.981980] mmc1: CQHCI version 5.10 [ 1.986383] sdhci-esdhc-imx 5b020000.mmc: could not get ultra high speed state, work on normal mode [ 1.999279] ledtrig-cpu: registered to indicate activity on CPUs [ 2.007750] usbcore: registered new interface driver usbhid [ 2.013404] usbhid: USB HID core driver [ 2.017841] mxc-md bus@58000000:camera: deferring cap_device device registration [ 2.026803] mxc-isi 58100000.isi: mxc_isi.0 registered successfully [ 2.033452] mxc-isi 58110000.isi: mxc_isi.1 registered successfully [ 2.039991] mxc-isi 58120000.isi: mxc_isi.2 registered successfully [ 2.046552] mxc-isi 58130000.isi: mxc_isi.3 registered successfully [ 2.057265] No fsl,qman node [ 2.060198] Freescale USDPAA process driver [ 2.064414] fsl-usdpaa: no region found [ 2.068287] Freescale USDPAA process IRQ driver [ 2.086744] Galcore version 6.4.3.p1.305572 [ 2.123613] mmc0: Command Queue Engine enabled [ 2.128100] mmc0: new HS400 Enhanced strobe MMC card at address 0001 [ 2.135643] mmcblk0: mmc0:0001 HAG4a2 14.7 GiB [ 2.140441] mmcblk0boot0: mmc0:0001 HAG4a2 partition 1 8.00 MiB [ 2.146582] mmcblk0boot1: mmc0:0001 HAG4a2 partition 2 8.00 MiB [ 2.152809] mmcblk0rpmb: mmc0:0001 HAG4a2 partition 3 4.00 MiB, chardev (242:0) [ 2.163595] mmcblk0: p1 p2 p3 p4 p5 p6 p7 [ 2.187416] [drm] Initialized vivante 1.0.0 20170808 for 80000000.imx8_gpu0_ss on minor 0 [ 2.200398] [VPU Decoder] warning: init rtx channel failed, ret: -517 [ 2.206930] [VPU Decoder] failed to request mailbox, ret = -517 [ 2.219155] [VPU Encoder] warning: init rtx channel failed, ret: -517 [ 2.225774] [VPU Encoder] fail to request mailbox, ret = -517 [ 2.240327] fsl-sai 59050000.sai: Unbalanced pm_runtime_enable! [ 2.251199] NET: Registered protocol family 26 [ 2.256395] NET: Registered protocol family 10 [ 2.261683] Segment Routing with IPv6 [ 2.265432] NET: Registered protocol family 17 [ 2.269920] can: controller area network core (rev 20170425 abi 9) [ 2.276153] NET: Registered protocol family 29 [ 2.280608] can: raw protocol (rev 20170425) [ 2.284910] can: broadcast manager protocol (rev 20170425 t) [ 2.290599] can: netlink gateway (rev 20190810) max_hops=1 [ 2.296347] Bluetooth: RFCOMM TTY layer initialized [ 2.301239] Bluetooth: RFCOMM socket layer initialized [ 2.306429] Bluetooth: RFCOMM ver 1.11 [ 2.310199] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.315526] Bluetooth: BNEP filters: protocol multicast [ 2.320780] Bluetooth: BNEP socket layer initialized [ 2.325759] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.331711] Bluetooth: HIDP socket layer initialized [ 2.336735] 8021q: 802.1Q VLAN Support v1.8 [ 2.340947] lib80211: common routines for IEEE802.11 drivers [ 2.346752] 9pnet: Installing 9P2000 support [ 2.351090] Key type dns_resolver registered [ 2.355664] batman_adv: B.A.T.M.A.N. advanced 2019.4 (compatibility version 15) loaded [ 2.364056] registered taskstats version 1 [ 2.368167] Loading compiled-in X.509 certificates [ 2.399483] mxs_phy 5b100000.usbphy: 5b100000.usbphy supply phy-3p0 not found, using dummy regulator [ 2.421434] 3v3_rf: supplied by 3v3 [ 2.425364] rf_wl_en: supplied by 3v3_rf [ 2.429726] rf_bt_en: supplied by 3v3_rf [ 2.434252] usb_phy_generic bus@5b000000:usb3-phy: bus@5b000000:usb3-phy supply vcc not found, using dummy regulator [ 2.445455] gpio-104 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 2.454448] imx-lpi2c 5a800000.i2c: using scl,sda for recovery [ 2.469017] mca-rtc mca-cc8x-rtc: registered as rtc0 [ 2.479845] Watchdog driver for MCA (timeout=30 sec, nowayout=1, reset (full)) [ 2.497339] mca_cc8 0-0063: Invalid MCA firmware version for key-power-up. Required MCAv0.17 or above [ 2.511173] input: mca-cc8x-pwrkey as /devices/platform/bus@5a000000/5a800000.i2c/i2c-0/0-0063/mca-cc8x-pwrkey/input/input1 [ 2.523867] ADC driver for MCA [ 2.527626] Tamper driver for MCA [ 2.531640] mca-uart mca-cc8x-uart: UART is not supported in MCA firmware v0.12. [ 2.539783] mca-pwm mca-pwm: registered PWM chip (tpm: 0, channels: 6) [ 2.546389] mca-pwm mca-pwm: registered PWM chip (tpm: 1, channels: 2) [ 2.553001] mca-pwm mca-pwm: registered PWM chip (tpm: 2, channels: 2) [ 2.561007] i2c i2c-0: LPI2C adapter registered [ 2.566140] imx-lpi2c 5a820000.i2c: can't get I2C ipg clock [ 2.571781] imx-lpi2c: probe of 5a820000.i2c failed with error -2 [ 2.581834] tlv320aic31xx-codec 3-0018: 3-0018 supply HPVDD not found, using dummy regulator [ 2.590388] tlv320aic31xx-codec 3-0018: 3-0018 supply SPRVDD not found, using dummy regulator [ 2.598974] tlv320aic31xx-codec 3-0018: 3-0018 supply SPLVDD not found, using dummy regulator [ 2.607561] tlv320aic31xx-codec 3-0018: 3-0018 supply AVDD not found, using dummy regulator [ 2.615974] tlv320aic31xx-codec 3-0018: 3-0018 supply IOVDD not found, using dummy regulator [ 2.624501] tlv320aic31xx-codec 3-0018: 3-0018 supply DVDD not found, using dummy regulator [ 2.632997] i2c i2c-3: LPI2C adapter registered [ 2.639071] imx-lpi2c 56226000.i2c: can't get irq number [ 2.649045] pwm-backlight lvds_backlight@0: lvds_backlight@0 supply power not found, using dummy regulator [ 2.649506] imx6q-pcie 5f010000.pcie: No cache used with register defaults set! [ 2.671731] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.678404] [drm] No driver support for vblank timestamp query. [ 2.684418] imx-drm display-subsystem: bound imx-drm-dpu-bliteng.2 (ops 0xffff800010f6c9a0) [ 2.693472] imx-drm display-subsystem: bound imx-dpu-crtc.0 (ops 0xffff800010f6c668) [ 2.701813] imx-drm display-subsystem: bound imx-dpu-crtc.1 (ops 0xffff800010f6c668) [ 2.710512] dpu-core 56180000.dpu: driver probed [ 2.788620] pps pps0: new PPS source ptp0 [ 2.795254] libphy: fec_enet_mii_bus: probed [ 2.800282] imx6q-pcie 5f010000.pcie: PCIe PLL locked after 0 us. [ 2.806454] imx6q-pcie 5f010000.pcie: host bridge /bus@5f000000/pcie@0x5f010000 ranges: [ 2.814567] imx6q-pcie 5f010000.pcie: IO 0x7ff80000..0x7ff8ffff -> 0x00000000 [ 2.815286] fec 5b040000.ethernet eth0: registered PHC device 0 [ 2.822012] imx6q-pcie 5f010000.pcie: MEM 0x70000000..0x7fefffff -> 0x70000000 [ 2.838923] xhci-cdns3: xHCI Host Controller [ 2.843308] xhci-cdns3: new USB bus registered, assigned bus number 1 [ 2.851098] xhci-cdns3: hcc params 0x200073c8 hci version 0x100 quirks 0x0000001000018010 [ 2.860214] hub 1-0:1.0: USB hub found [ 2.864018] hub 1-0:1.0: 1 port detected [ 2.868267] xhci-cdns3: xHCI Host Controller [ 2.872646] xhci-cdns3: new USB bus registered, assigned bus number 2 [ 2.879194] xhci-cdns3: Host supports USB 3.0 SuperSpeed [ 2.884664] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.893246] hub 2-0:1.0: USB hub found [ 2.897039] hub 2-0:1.0: 1 port detected [ 2.902642] imx_usb 5b0d0000.usb: 5b0d0000.usb supply vbus not found, using dummy regulator [ 2.914571] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 2.919485] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 3 [ 2.935474] imx6q-pcie 5f010000.pcie: Link up [ 2.940568] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 2.940628] imx6q-pcie 5f010000.pcie: Link up [ 2.946741] hub 3-0:1.0: USB hub found [ 2.951094] imx6q-pcie 5f010000.pcie: Link up, Gen1 [ 2.954144] hub 3-0:1.0: 1 port detected [ 2.959150] imx6q-pcie 5f010000.pcie: PCI host bridge to bus 0000:00 [ 2.969379] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.974971] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.981202] pci_bus 0000:00: root bus resource [mem 0x70000000-0x7fefffff] [ 2.988132] mmc1: CQHCI version 5.10 [ 2.988161] pci 0000:00:00.0: [1957:0000] type 01 class 0x060400 [ 2.991733] sdhci-esdhc-imx 5b020000.mmc: could not get ultra high speed state, work on normal mode [ 2.997752] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 3.006840] sdhci-esdhc-imx 5b020000.mmc: Got CD GPIO [ 3.013083] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x00ffffff pref] [ 3.024893] pci 0000:00:00.0: supports D1 D2 [ 3.029199] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.041440] pci 0000:01:00.0: [168c:003e] type 00 class 0x028000 [ 3.047590] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 3.049699] mmc1: SDHCI controller on 5b020000.mmc [5b020000.mmc] using ADMA [ 3.054778] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.071881] mxc-md bus@58000000:camera: deferring cap_device device registration [ 3.082755] pci 0000:00:00.0: BAR 0: assigned [mem 0x70000000-0x70ffffff] [ 3.089708] pci 0000:00:00.0: BAR 6: assigned [mem 0x71000000-0x71ffffff pref] [ 3.097019] pci 0000:00:00.0: BAR 14: assigned [mem 0x72000000-0x721fffff] [ 3.103942] pci 0000:01:00.0: BAR 0: assigned [mem 0x72000000-0x721fffff 64bit] [ 3.111351] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.116617] pci 0000:00:00.0: bridge window [mem 0x72000000-0x721fffff] [ 3.124091] pcieport 0000:00:00.0: PME: Signaling with IRQ 446 [ 3.148679] tlv320aic31xx-codec 3-0018: ASoC: sink widget SPK ClassD overwritten [ 3.156110] tlv320aic31xx-codec 3-0018: ASoC: source widget SPK ClassD overwritten [ 3.163862] debugfs: Directory '59050000.sai' with parent 'imx8-tlv320' already present! [ 3.172072] asoc-simple-card sound: tlv320dac31xx-hifi <-> 59050000.sai mapping ok [ 3.179700] asoc-simple-card sound: ASoC: no DMI vendor name! [ 3.186939] tlv320aic31xx-codec 3-0018: Could not reset device: -5 [ 3.195471] gpio-57 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 3.200302] usb 1-1: new full-speed USB device number 2 using cdns-usb3 [ 3.204406] imx-lpi2c 56226000.i2c: using scl,sda for recovery [ 3.217468] Goodix-TS 16-0014: No vin supply [ 3.280410] Goodix-TS 16-0014: i2c test failed attempt 1: -5 [ 3.312443] Goodix-TS 16-0014: i2c test failed attempt 2: -5 [ 3.344303] Goodix-TS 16-0014: I2C communication failure: -5 [ 3.350042] Goodix-TS: probe of 16-0014 failed with error -5 [ 3.355991] Goodix-TS 16-005d: No vin supply [ 3.361468] hid-generic 0003:7374:1262.0001: device has no listeners, quitting [ 3.370645] input: DATA MODUL easyTOUCH as /devices/platform/bus@5b000000/5b110000.usb3/xhci-cdns3/usb1/1-1/1-1:1.1/0003:7374:1262.0002/input/input2 [ 3.384144] hid-multitouch 0003:7374:1262.0002: input: USB HID v1.11 Device [DATA MODUL easyTOUCH] on usb-xhci-cdns3-1/input1 [ 3.395720] usb-storage 1-1:1.2: USB Mass Storage device detected [ 3.402135] scsi host0: usb-storage 1-1:1.2 [ 3.421184] Goodix-TS 16-005d: i2c test failed attempt 1: -5 [ 3.452418] Goodix-TS 16-005d: i2c test failed attempt 2: -5 [ 3.484270] Goodix-TS 16-005d: I2C communication failure: -5 [ 3.489979] Goodix-TS: probe of 16-005d failed with error -5 [ 3.495745] i2c i2c-16: LPI2C adapter registered [ 3.500815] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 3.507451] [drm] No driver support for vblank timestamp query. [ 3.513475] imx-drm display-subsystem: bound imx-drm-dpu-bliteng.2 (ops 0xffff800010f6c9a0) [ 3.522928] imx-drm display-subsystem: bound imx-dpu-crtc.0 (ops 0xffff800010f6c668) [ 3.530930] imx-drm display-subsystem: bound imx-dpu-crtc.1 (ops 0xffff800010f6c668) [ 3.539314] imx-drm display-subsystem: bound bus@56220000:ldb@562210e0 (ops 0xffff800010f6c048) [ 3.548594] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 1 [ 3.649905] Console: switching to colour frame buffer device 100x30 [ 3.672861] imx-drm display-subsystem: fb0: imx-drmdrmfb frame buffer device [ 3.681897] mxc-md bus@58000000:camera: deferring cap_device device registration [ 3.691335] mxc-md bus@58000000:camera: deferring cap_device device registration [ 3.711360] mca-rtc mca-cc8x-rtc: setting system clock to 2021-09-21T09:18:31 UTC (1632215911) [ 3.721307] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.730287] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.736959] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.745599] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 3.754510] ALSA device list: [ 3.757506] #0: imx8-tlv320 [ 3.789469] EXT4-fs (mmcblk0p3): recovery complete [ 3.794906] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null) [ 3.803095] VFS: Mounted root (ext4 filesystem) on device 179:3. [ 3.809531] devtmpfs: mounted [ 3.813357] Freeing unused kernel memory: 2496K [ 3.818009] Run /sbin/init as init process [ 3.891841] systemd[1]: systemd 243.2+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.914181] systemd[1]: Detected architecture arm64. Welcome to Digi Embedded Yocto 3.0-r4 (zeus)! [ 3.976714] systemd[1]: Set hostname to . [ 4.179093] systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly. [ 4.325511] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 4.337941] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 4.349421] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 4.375118] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 4.402007] systemd[1]: Created slice system-weston.slice. [ OK ] Created slice system-weston.slice. [ 4.417021] scsi 0:0:0:0: Direct-Access DM easyTOUCH 1.00 PQ: 0 ANSI: 3 [ 4.426781] sd 0:0:0:0: [sda] 92 512-byte logical blocks: (47.1 kB/46.0 KiB) [ 4.434974] sd 0:0:0:0: [sda] Write Protect is off [ 4.440157] sd 0:0:0:0: [sda] No Caching mode page found [ 4.445493] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 4.462897] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 4.481713] sda: [ OK [ 04m.486211] sd 0:0:0:0: [sda] Attached SCSI removable disk ] Started Dis[p a t c h4 .P4a9s4s1w7o5r]d mâx€c¦-tms d tbou sC@o5n8s0o0l0e0 0D0i:rceacmteorray: Wdaetfcehr[i0nmg. c ap_device device registration [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Paths. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Syslog Socket. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Temporary Directory (/tmp)... Starting Create list of st…odes for the current kernel... Starting Starts Psplash Boot screen... Starting Journal Service... Starting Load Kernel Modules... [ 4 .876979] cryptodev: loading out-of-tree module taints kernel. Starting Remount Root and Kernel File Sy[s t e m s4[08m7.9.0.5] cryptodev: driver 1.10 loaded. Starting udev[ C o l d4p.9l0ug25 a1l1l] DEeXvTi4c-efss mmc..b.lk 0p3): re-mounted. Opts: (null) [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ 4.962724] audit: type=1701 audit(1632215912.748:2): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=350 comm="psplash" exe="/usr/bin/psplash.psplash-oven" sig=11 res=1 [ OK ] Started Journal Service. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta… nodes for the current kernel. [ OK ] Started Load Kernel Modules. [ OK ] Started Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ 5.141857] systemd-journald[333]: Received client request to flush runtime journal. Starting Apply Kernel Variables... [ 5.155185] systemd-journald[333]: File /var/log/journal/82e3ac91564744f79fde7d7cb5a97a7a/system.journal corrupted or uncleanly shut down, renaming and replacing. Starting Create Static Device Nodes in /dev... [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Apply Kernel Variables. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Coldplug all Devices. Starting udev Wait for Complete Device Initialization... [ 5.806460] mxc-md bus@58000000:camera: deferring cap_device device registration [ 5.847049] [VPU Encoder] enable mu for core[0] [ 5.859926] [VPU Encoder] vpu encoder core[0] firmware version is 1.3.0 [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen … backlight:lvds_backlight@0... [ OK ] Started Load/Save Screen B…of backlight:lvds_backlight@0. [ 6.575623] qca65x4: Setting US wireless region [ OK ] Created slice system-systemd\x2dfsck.slice. Starting File System Check on /dev/mmcblk0p1... Starting File System Check on /dev/mmcblk0p4... [ OK ] Started File System Check on /dev/mmcblk0p1. [ OK ] Found device easyTOUCH Max_Touch. [ OK ] Started File System Check on /dev/mmcblk0p4. [ OK ] Found device /dev/mmcblk0p7. Mounting /Oven... Mounting /mnt/linux... Mounting /mnt/update... Starting File System Check on /dev/sda... [ OK ] Mounted /Oven. [ OK ] Mounted /mnt/linux. [ OK ] Mounted /mnt/update. [ OK ] Started File System Check on /dev/sda. Mounting /run/media/sda... [ OK ] Mounted /run/media/sda. [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ 7.999822] ol_download_firmware: chip_id:0x5030000 board_id:0x0 [ OK ] Started udev Wait for Complete Device Initialization. [* ] A start job is running for Starts Psplash Boot screen (7s / 1min 28s) [** ] A start job is running for Starts Psplash Boot screen (8s / 1min 28s) [ OK ] Started Starts Psplash Boot screen. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Run foo hourly. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket. [ OK ] Listening on SWUpdate socket listener. [ OK ] Listening on sshd.socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Save/Restore Sound Card State... Starting Initialization of the bluetooth chip... Starting Enable CAN interface... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Configuration for i.MX GPU (Former rc_gpu.S). Starting Interface initialization via ifupdown... Starting Packet Filtering Framework... Starting Network Time Service (one-shot ntpdate mode)... Starting System-wide sound service... [ OK ] Started User Space Regulatory Firmware Loading. Starting Service to restart rsyslog service hourly... Starting System Logging Service... [ OK ] Started User Space SDMA Firmware Loading. [ OK ] Started SWUpdate daemon. Starting Login Service... Starting XBee GPIOs initialization... [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Enable CAN interface. [ OK ] Started System Logging Service. [ OK ] Started Interface initialization via ifupdown. [ OK ] Started Packet Filtering Framework. [ OK ] Started Network Time Service (one-shot ntpdate mode). [ OK ] Reached target Network (Pre). [ OK ] Reached target Sound Card. Starting Connection service... Stopping System Logging Service... [ OK ] Stopped System Logging Service. [ OK ] Started XBee GPIOs initialization. Starting System Logging Service... [ OK ] Started System Logging Service. [ OK ] Started Service to restart rsyslog service hourly. [ 15.734364] tlv320aic31xx-codec 3-0018: ASoC: Speaker DAPM update failed: -5 [ OK ] Started Login Service. [ OK ] Started System-wide sound service. [ OK ] Started Connection service. [ OK ] Reached target Network. Starting Busybox HTTP daemon... Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Vsftpd ftp daemon. [ OK ] Started Busybox HTTP daemon. [ OK ] Started Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Getty on tty2. [ OK ] Started Serial Getty on ttyLP2. [ OK ] Reached target Login Prompts. Starting Hostname Service... Starting Weston Wayland Compositor (on tty7)... Starting WPA supplicant... [ OK ] Started Initialization of the bluetooth chip. [ OK ] Started Target Communication Framework agent. [ OK ] Started Weston Wayland Compositor (on tty7). [ OK ] Started WPA supplicant. [ OK ] Started Hostname Service. [ OK ] Created slice User Slice of UID 0. [ OK ] Reached target Bluetooth. Starting Bluetooth service... Starting User Runtime Directory /run/user/0... [ OK ] Started User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ OK ] Started Bluetooth service. [ OK ] Reached target Multi-User System. [ OK ] Started Oven Advance Application. Starting Update UTMP about System Runlevel Changes... [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Started User Manager for UID 0. [ OK ] Started Session c1 of user root. Digi Embedded Yocto 3.0-r4 ccimx8x-sbc-express ttyLP2 ccimx8x-sbc-express login: