[2021-04-08 13:30:52.928] [2021-04-08 13:30:52.928] [2021-04-08 13:30:52.928] U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1bf9f (Apr 07 2021 - 17:37:04 +0530) [2021-04-08 13:30:52.928] [2021-04-08 13:30:52.928] CPU: Freescale i.MX6DL rev1.2 at 792MHz [2021-04-08 13:30:52.928] CPU: Automotive temperature grade (-40C to 125C) at 42C [2021-04-08 13:30:52.928] Reset cause: POR [2021-04-08 13:30:52.928] Model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:30:52.943] Board: MX6-SabreSD [2021-04-08 13:30:52.943] DRAM: 1 GiB [2021-04-08 13:30:53.006] MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 [2021-04-08 13:30:53.043] MMC: no card present [2021-04-08 13:30:53.043] mmc_init: -123, time 2 [2021-04-08 13:30:53.043] *** Warning - MMC init failed, using default environment [2021-04-08 13:30:53.043] [2021-04-08 13:30:53.043] No panel detected: default to Hannstar-XGA [2021-04-08 13:30:53.043] Display: Hannstar-XGA (1024x768) [2021-04-08 13:30:53.150] In: serial [2021-04-08 13:30:53.150] Out: serial [2021-04-08 13:30:53.150] Err: serial [2021-04-08 13:30:53.150] MMC: no card present [2021-04-08 13:30:53.150] mmc_init: -123, time 2 [2021-04-08 13:30:53.150] Net: No ethernet found. [2021-04-08 13:30:53.150] Boot from USB for mfgtools [2021-04-08 13:30:53.150] Use default environment for mfgtools [2021-04-08 13:30:53.150] Run bootcmd_mfg: run mfgtool_args; if test ${tee} = yes; then bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; else bootz ${loadaddr} ${initrd_addr} ${fdt_addr}; fi; [2021-04-08 13:30:53.150] Hit any key to stop autoboot: 0 [2021-04-08 13:30:53.150] Kernel image @ 0x12000000 [ 0x000000 - 0x554130 ] [2021-04-08 13:30:53.150] ## Loading init Ramdisk from Legacy Image at 12c00000 ... [2021-04-08 13:30:53.150] Image Name: fsl-image-mfgtool-initramfs-imx6 [2021-04-08 13:30:53.150] Image Type: ARM Linux RAMDisk Image (gzip compressed) [2021-04-08 13:30:53.150] Data Size: 8591032 Bytes = 8.2 MiB [2021-04-08 13:30:53.150] Load Address: 00000000 [2021-04-08 13:30:53.150] Entry Point: 00000000 [2021-04-08 13:30:53.150] Verifying Checksum ... OK [2021-04-08 13:30:53.231] ## Flattened Device Tree blob at 18000000 [2021-04-08 13:30:53.258] Booting using the fdt blob at 0x18000000 [2021-04-08 13:30:53.258] Using Device Tree in place at 18000000, end 1800e4f1 [2021-04-08 13:30:53.258] No PMIC found! [2021-04-08 13:30:53.258] [2021-04-08 13:30:53.258] Starting kernel ... [2021-04-08 13:30:53.258] [2021-04-08 13:30:54.920] Booting Linux on physical CPU 0x0 [2021-04-08 13:30:54.920] Linux version 4.1.15+ (bamboo@yb6) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Fri Sep 16 18:10:49 CDT 2016 [2021-04-08 13:30:54.920] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [2021-04-08 13:30:54.920] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [2021-04-08 13:30:54.920] Machine model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:30:54.920] Reserved memory: created CMA memory pool at 0x3c000000, size 320 MiB [2021-04-08 13:30:54.920] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool [2021-04-08 13:30:54.920] Memory policy: Data cache writealloc [2021-04-08 13:30:54.920] PERCPU: Embedded 12 pages/cpu @ab71c000 s16716 r8192 d24244 u49152 [2021-04-08 13:30:54.920] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [2021-04-08 13:30:54.920] Kernel command line: console=ttymxc0,115200 rdinit=/linuxrc g_mass_storage.stall=0 g_mass_storage.removable=1 g_mass_storage.file=/fat g_mass_storage.ro=1 g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF g_mass_storage.iSerialNumber= enable_wait_mode=off [2021-04-08 13:30:54.920] PID hash table entries: 4096 (order: 2, 16384 bytes) [2021-04-08 13:30:54.920] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [2021-04-08 13:30:54.931] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [2021-04-08 13:30:54.931] Memory: 692096K/1048576K available (6903K kernel code, 320K rwdata, 2416K rodata, 384K init, 423K bss, 28800K reserved, 327680K cma-reserved, 0K highmem) [2021-04-08 13:30:54.931] Virtual kernel memory layout: [2021-04-08 13:30:54.931] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [2021-04-08 13:30:54.931] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [2021-04-08 13:30:54.931] vmalloc : 0xc0800000 - 0xff000000 (1000 MB) [2021-04-08 13:30:54.931] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [2021-04-08 13:30:54.931] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [2021-04-08 13:30:54.931] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [2021-04-08 13:30:54.931] .text : 0x80008000 - 0x80921fd8 (9320 kB) [2021-04-08 13:30:54.931] .init : 0x80922000 - 0x80982000 ( 384 kB) [2021-04-08 13:30:54.931] .data : 0x80982000 - 0x809d2080 ( 321 kB) [2021-04-08 13:30:54.931] .bss : 0x809d5000 - 0x80a3ee54 ( 424 kB) [2021-04-08 13:30:54.931] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [2021-04-08 13:30:54.931] Preemptible hierarchical RCU implementation. [2021-04-08 13:30:54.931] Additional per-CPU info printed with stalls. [2021-04-08 13:30:54.931] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [2021-04-08 13:30:54.948] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [2021-04-08 13:30:54.948] NR_IRQS:16 nr_irqs:16 16 [2021-04-08 13:30:54.948] L2C-310 erratum 769419 enabled [2021-04-08 13:30:54.948] L2C-310 enabling early BRESP for Cortex-A9 [2021-04-08 13:30:54.948] L2C-310 full line of zeros enabled for Cortex-A9 [2021-04-08 13:30:54.948] L2C-310 ID prefetch enabled, offset 16 lines [2021-04-08 13:30:54.948] L2C-310 dynamic clock gating enabled, standby mode enabled [2021-04-08 13:30:54.948] L2C-310 cache controller enabled, 16 ways, 512 kB [2021-04-08 13:30:54.948] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [2021-04-08 13:30:54.948] mxc_clocksource_init 3000000 [2021-04-08 13:30:54.948] Switching to timer-based delay loop, resolution 333ns [2021-04-08 13:30:54.948] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [2021-04-08 13:30:54.948] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [2021-04-08 13:30:54.948] Console: colour dummy device 80x30 [2021-04-08 13:30:54.948] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [2021-04-08 13:30:54.948] pid_max: default: 32768 minimum: 301 [2021-04-08 13:30:54.948] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:30:54.948] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:30:54.948] CPU: Testing write buffer coherency: ok [2021-04-08 13:30:54.964] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [2021-04-08 13:30:54.964] Setting up static identity map for 0x10008280 - 0x100082f0 [2021-04-08 13:30:54.964] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [2021-04-08 13:30:54.964] Brought up 2 CPUs [2021-04-08 13:30:54.964] SMP: Total of 2 processors activated (12.00 BogoMIPS). [2021-04-08 13:30:54.964] CPU: All CPU(s) started in SVC mode. [2021-04-08 13:30:54.964] devtmpfs: initialized [2021-04-08 13:30:54.964] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [2021-04-08 13:30:54.964] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [2021-04-08 13:30:54.964] pinctrl core: initialized pinctrl subsystem [2021-04-08 13:30:54.964] NET: Registered protocol family 16 [2021-04-08 13:30:54.964] DMA: preallocated 256 KiB pool for atomic coherent allocations [2021-04-08 13:30:54.964] cpuidle: using governor ladder [2021-04-08 13:30:54.964] cpuidle: using governor menu [2021-04-08 13:30:54.964] CPU identified as i.MX6DL, silicon rev 1.2 [2021-04-08 13:30:54.964] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [2021-04-08 13:30:54.964] hw-breakpoint: maximum watchpoint size is 4 bytes. [2021-04-08 13:30:54.964] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [2021-04-08 13:30:55.194] mxs-dma 110000.dma-apbh: initialized [2021-04-08 13:30:55.194] SCSI subsystem initialized [2021-04-08 13:30:55.194] usbcore: registered new interface driver usbfs [2021-04-08 13:30:55.194] usbcore: registered new interface driver hub [2021-04-08 13:30:55.194] usbcore: registered new device driver usb [2021-04-08 13:30:55.194] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator [2021-04-08 13:30:55.194] 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator [2021-04-08 13:30:55.194] i2c i2c-0: IMX I2C adapter registered [2021-04-08 13:30:55.194] i2c i2c-0: can't use DMA [2021-04-08 13:30:55.194] i2c i2c-1: IMX I2C adapter registered [2021-04-08 13:30:55.194] i2c i2c-1: can't use DMA [2021-04-08 13:30:55.194] i2c i2c-2: IMX I2C adapter registered [2021-04-08 13:30:55.194] i2c i2c-2: can't use DMA [2021-04-08 13:30:55.194] Linux video capture interface: v2.00 [2021-04-08 13:30:55.194] pps_core: LinuxPPS API ver. 1 registered [2021-04-08 13:30:55.194] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [2021-04-08 13:30:55.194] PTP clock support registered [2021-04-08 13:30:55.194] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [2021-04-08 13:30:55.194] Advanced Linux Sound Architecture Driver Initialized. [2021-04-08 13:30:55.194] Switched to clocksource mxc_timer1 [2021-04-08 13:30:55.194] NET: Registered protocol family 2 [2021-04-08 13:30:55.194] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [2021-04-08 13:30:55.194] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [2021-04-08 13:30:55.210] TCP: Hash tables configured (established 8192 bind 8192) [2021-04-08 13:30:55.210] UDP hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:30:55.210] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:30:55.210] NET: Registered protocol family 1 [2021-04-08 13:30:55.210] RPC: Registered named UNIX socket transport module. [2021-04-08 13:30:55.210] RPC: Registered udp transport module. [2021-04-08 13:30:55.210] RPC: Registered tcp transport module. [2021-04-08 13:30:55.210] RPC: Registered tcp NFSv4.1 backchannel transport module. [2021-04-08 13:30:55.210] Trying to unpack rootfs image as initramfs... [2021-04-08 13:30:55.210] Freeing initrd memory: 8392K (82c00000 - 83432000) [2021-04-08 13:30:55.210] CPU PMU: Failed to parse /soc/pmu/interrupt-affinity[0] [2021-04-08 13:30:55.210] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [2021-04-08 13:30:55.210] imx rpmsg driver is registered. [2021-04-08 13:30:55.210] Bus freq driver module loaded [2021-04-08 13:30:55.210] futex hash table entries: 512 (order: 3, 32768 bytes) [2021-04-08 13:30:55.210] VFS: Disk quotas dquot_6.6.0 [2021-04-08 13:30:55.210] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [2021-04-08 13:30:55.210] NFS: Registering the id_resolver key type [2021-04-08 13:30:55.210] Key type id_resolver registered [2021-04-08 13:30:55.210] Key type id_legacy registered [2021-04-08 13:30:55.210] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [2021-04-08 13:30:55.228] fuse init (API version 7.23) [2021-04-08 13:30:55.228] io scheduler noop registered [2021-04-08 13:30:55.228] io scheduler deadline registered [2021-04-08 13:30:55.228] io scheduler cfq registered (default) [2021-04-08 13:30:55.228] imx-weim 21b8000.weim: Driver registered. [2021-04-08 13:30:55.228] backlight supply power not found, using dummy regulator [2021-04-08 13:30:55.228] mxc_sdc_fb fb@0: NO mxc display driver found! [2021-04-08 13:30:55.228] mxc_sdc_fb fb@1: NO mxc display driver found! [2021-04-08 13:30:55.228] imx-sdma 20ec000.sdma: no iram assigned, using external mem [2021-04-08 13:30:55.228] imx-sdma 20ec000.sdma: no event needs to be remapped [2021-04-08 13:30:55.228] imx-sdma 20ec000.sdma: initialized [2021-04-08 13:30:55.228] pfuze100-regulator 1-0008: unrecognized pfuze chip ID! [2021-04-08 13:30:55.228] imx-sdma 20ec000.sdma: loaded firmware 3.3 [2021-04-08 13:30:55.228] pfuze100-regulator: probe of 1-0008 failed with error -5 [2021-04-08 13:30:55.228] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [2021-04-08 13:30:55.228] console [ttymxc0] enabled [2021-04-08 13:30:55.228] imx sema4 driver is registered. [2021-04-08 13:30:55.228] [drm] Initialized drm 1.1.0 20060810 [2021-04-08 13:30:55.228] [drm] Initialized vivante 1.0.0 20120216 on minor 0 [2021-04-08 13:30:55.228] brd: module loaded [2021-04-08 13:30:55.243] loop: module loaded [2021-04-08 13:30:55.243] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 0, 0 [2021-04-08 13:30:55.243] spi_imx 2008000.ecspi: probed [2021-04-08 13:30:55.243] 2188000.ethernet supply phy not found, using dummy regulator [2021-04-08 13:30:55.462] pps pps0: new PPS source ptp0 [2021-04-08 13:30:55.462] fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 [2021-04-08 13:30:55.462] fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 82:56:de:80:a0:73 [2021-04-08 13:30:55.462] libphy: fec_enet_mii_bus: probed [2021-04-08 13:30:55.462] fec 2188000.ethernet eth0: registered PHC device 0 [2021-04-08 13:30:55.462] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [2021-04-08 13:30:55.462] ehci-mxc: Freescale On-Chip EHCI Host driver [2021-04-08 13:30:55.462] usbcore: registered new interface driver usb-storage [2021-04-08 13:30:55.462] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator [2021-04-08 13:30:55.462] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:30:55.462] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.462] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:30:55.462] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.462] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers [2021-04-08 13:30:55.462] mousedev: PS/2 mouse device common for all mice [2021-04-08 13:30:55.462] egalax_ts 1-0004: Failed to read firmware version [2021-04-08 13:30:55.479] egalax_ts: probe of 1-0004 failed with error -5 [2021-04-08 13:30:55.479] egalax_ts 2-0004: Failed to read firmware version [2021-04-08 13:30:55.479] egalax_ts: probe of 2-0004 failed with error -5 [2021-04-08 13:30:55.479] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0 [2021-04-08 13:30:55.479] i2c /dev entries driver [2021-04-08 13:30:55.480] IR NEC protocol handler initialized [2021-04-08 13:30:55.480] IR RC5(x/sz) protocol handler initialized [2021-04-08 13:30:55.480] IR RC6 protocol handler initialized [2021-04-08 13:30:55.480] IR JVC protocol handler initialized [2021-04-08 13:30:55.480] IR Sony protocol handler initialized [2021-04-08 13:30:55.480] IR SANYO protocol handler initialized [2021-04-08 13:30:55.480] IR Sharp protocol handler initialized [2021-04-08 13:30:55.480] IR MCE Keyboard/mouse protocol handler initialized [2021-04-08 13:30:55.480] IR XMP protocol handler initialized [2021-04-08 13:30:55.480] imx2-wdt 20c0000.wdog: use WDOG_B to reboot. [2021-04-08 13:30:55.480] imx2-wdt 20c0000.wdog: timeout 60 sec (nowayout=0) [2021-04-08 13:30:55.480] sdhci: Secure Digital Host Controller Interface driver [2021-04-08 13:30:55.480] sdhci: Copyright(c) Pierre Ossman [2021-04-08 13:30:55.480] sdhci-pltfm: SDHCI platform and OF driver helper [2021-04-08 13:30:55.480] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified [2021-04-08 13:30:55.480] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [2021-04-08 13:30:55.493] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [2021-04-08 13:30:55.493] sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found [2021-04-08 13:30:55.493] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found [2021-04-08 13:30:55.496] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [2021-04-08 13:30:55.528] /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified [2021-04-08 13:30:55.528] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [2021-04-08 13:30:55.528] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [2021-04-08 13:30:55.528] sdhci-esdhc-imx 2198000.usdhc: No vmmc regulator found [2021-04-08 13:30:55.528] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [2021-04-08 13:30:55.604] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [2021-04-08 13:30:55.604] /soc/aips-bus@02100000/usdhc@0219c000: voltage-ranges unspecified [2021-04-08 13:30:55.604] sdhci-esdhc-imx 219c000.usdhc: No vmmc regulator found [2021-04-08 13:30:55.604] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [2021-04-08 13:30:55.634] mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [2021-04-08 13:30:55.816] mxc_vpu 2040000.vpu_fsl: VPU initialized [2021-04-08 13:30:55.816] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [2021-04-08 13:30:55.816] usbcore: registered new interface driver usbhid [2021-04-08 13:30:55.816] usbhid: USB HID core driver [2021-04-08 13:30:55.816] wm8962 0-001a: Failed to read ID register [2021-04-08 13:30:55.816] wm8962: probe of 0-001a failed with error -5 [2021-04-08 13:30:55.816] imx-wm8962 sound: failed to find codec platform device [2021-04-08 13:30:55.816] imx-wm8962: probe of sound failed with error -22 [2021-04-08 13:30:55.816] NET: Registered protocol family 10 [2021-04-08 13:30:55.816] sit: IPv6 over IPv4 tunneling driver [2021-04-08 13:30:55.816] NET: Registered protocol family 17 [2021-04-08 13:30:55.816] Key type dns_resolver registered [2021-04-08 13:30:55.816] cpu cpu0: failed to get regulators [2021-04-08 13:30:55.816] imx6q-cpufreq: probe of imx6q-cpufreq.0 failed with error -2 [2021-04-08 13:30:55.816] Registering SWP/SWPB emulation handler [2021-04-08 13:30:55.816] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:30:55.816] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.816] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:30:55.816] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.816] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [2021-04-08 13:30:55.827] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0) [2021-04-08 13:30:55.827] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:30:55.827] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.827] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:30:55.827] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:30:55.850] mipi_dsi_pwr_on: disabling [2021-04-08 13:30:55.850] hdmi-5v-supply: disabling [2021-04-08 13:30:55.850] sensor-supply: disabling [2021-04-08 13:30:55.850] wm8962-supply: disabling [2021-04-08 13:30:55.850] usb_h1_vbus: disabling [2021-04-08 13:30:55.850] usb_otg_vbus: disabling [2021-04-08 13:30:55.850] ALSA device list: [2021-04-08 13:30:55.850] No soundcards found. [2021-04-08 13:30:55.850] Freeing unused kernel memory: 384K (80922000 - 80982000) [2021-04-08 13:30:55.891] Starting UTP [2021-04-08 13:30:55.891] uuc 0.5 [built Sep 16 2016 02:36:28] [2021-04-08 13:30:55.891] UTP: Waiting for device to appear [2021-04-08 13:30:58.222] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:30:59.795] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:02.339] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:03.986] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:47.491] [2021-04-08 13:31:47.491] [2021-04-08 13:31:47.491] U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1bf9f (Apr 07 2021 - 17:37:04 +0530) [2021-04-08 13:31:47.491] [2021-04-08 13:31:47.491] CPU: Freescale i.MX6DL rev1.2 at 792MHz [2021-04-08 13:31:47.491] CPU: Automotive temperature grade (-40C to 125C) at 41C [2021-04-08 13:31:47.491] Reset cause: POR [2021-04-08 13:31:47.491] Model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:31:47.491] Board: MX6-SabreSD [2021-04-08 13:31:47.491] DRAM: 1 GiB [2021-04-08 13:31:47.552] MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 [2021-04-08 13:31:47.591] MMC: no card present [2021-04-08 13:31:47.591] mmc_init: -123, time 2 [2021-04-08 13:31:47.591] *** Warning - MMC init failed, using default environment [2021-04-08 13:31:47.591] [2021-04-08 13:31:47.591] No panel detected: default to Hannstar-XGA [2021-04-08 13:31:47.591] Display: Hannstar-XGA (1024x768) [2021-04-08 13:31:47.698] In: serial [2021-04-08 13:31:47.698] Out: serial [2021-04-08 13:31:47.698] Err: serial [2021-04-08 13:31:47.698] MMC: no card present [2021-04-08 13:31:47.698] mmc_init: -123, time 2 [2021-04-08 13:31:47.698] Net: No ethernet found. [2021-04-08 13:31:47.698] Boot from USB for mfgtools [2021-04-08 13:31:47.698] Use default environment for mfgtools [2021-04-08 13:31:47.698] Run bootcmd_mfg: run mfgtool_args; if test ${tee} = yes; then bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; else bootz ${loadaddr} ${initrd_addr} ${fdt_addr}; fi; [2021-04-08 13:31:47.698] Hit any key to stop autoboot: 0 [2021-04-08 13:31:47.698] Kernel image @ 0x12000000 [ 0x000000 - 0x554130 ] [2021-04-08 13:31:47.699] ## Loading init Ramdisk from Legacy Image at 12c00000 ... [2021-04-08 13:31:47.699] Image Name: fsl-image-mfgtool-initramfs-imx6 [2021-04-08 13:31:47.699] Image Type: ARM Linux RAMDisk Image (gzip compressed) [2021-04-08 13:31:47.699] Data Size: 8591032 Bytes = 8.2 MiB [2021-04-08 13:31:47.699] Load Address: 00000000 [2021-04-08 13:31:47.699] Entry Point: 00000000 [2021-04-08 13:31:47.699] Verifying Checksum ... OK [2021-04-08 13:31:47.816] ## Flattened Device Tree blob at 18000000 [2021-04-08 13:31:47.816] Booting using the fdt blob at 0x18000000 [2021-04-08 13:31:47.816] Using Device Tree in place at 18000000, end 1800e4f1 [2021-04-08 13:31:47.816] No PMIC found! [2021-04-08 13:31:47.816] [2021-04-08 13:31:47.816] Starting kernel ... [2021-04-08 13:31:47.816] [2021-04-08 13:31:49.471] Booting Linux on physical CPU 0x0 [2021-04-08 13:31:49.471] Linux version 4.1.15+ (bamboo@yb6) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Fri Sep 16 18:10:49 CDT 2016 [2021-04-08 13:31:49.471] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [2021-04-08 13:31:49.471] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [2021-04-08 13:31:49.471] Machine model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:31:49.471] Reserved memory: created CMA memory pool at 0x3c000000, size 320 MiB [2021-04-08 13:31:49.471] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool [2021-04-08 13:31:49.471] Memory policy: Data cache writealloc [2021-04-08 13:31:49.471] PERCPU: Embedded 12 pages/cpu @ab71c000 s16716 r8192 d24244 u49152 [2021-04-08 13:31:49.471] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [2021-04-08 13:31:49.471] Kernel command line: console=ttymxc0,115200 rdinit=/linuxrc g_mass_storage.stall=0 g_mass_storage.removable=1 g_mass_storage.file=/fat g_mass_storage.ro=1 g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF g_mass_storage.iSerialNumber= enable_wait_mode=off [2021-04-08 13:31:49.471] PID hash table entries: 4096 (order: 2, 16384 bytes) [2021-04-08 13:31:49.471] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [2021-04-08 13:31:49.487] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [2021-04-08 13:31:49.487] Memory: 692096K/1048576K available (6903K kernel code, 320K rwdata, 2416K rodata, 384K init, 423K bss, 28800K reserved, 327680K cma-reserved, 0K highmem) [2021-04-08 13:31:49.487] Virtual kernel memory layout: [2021-04-08 13:31:49.487] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [2021-04-08 13:31:49.487] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [2021-04-08 13:31:49.487] vmalloc : 0xc0800000 - 0xff000000 (1000 MB) [2021-04-08 13:31:49.487] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [2021-04-08 13:31:49.487] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [2021-04-08 13:31:49.487] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [2021-04-08 13:31:49.487] .text : 0x80008000 - 0x80921fd8 (9320 kB) [2021-04-08 13:31:49.487] .init : 0x80922000 - 0x80982000 ( 384 kB) [2021-04-08 13:31:49.487] .data : 0x80982000 - 0x809d2080 ( 321 kB) [2021-04-08 13:31:49.487] .bss : 0x809d5000 - 0x80a3ee54 ( 424 kB) [2021-04-08 13:31:49.487] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [2021-04-08 13:31:49.487] Preemptible hierarchical RCU implementation. [2021-04-08 13:31:49.487] Additional per-CPU info printed with stalls. [2021-04-08 13:31:49.487] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [2021-04-08 13:31:49.502] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [2021-04-08 13:31:49.502] NR_IRQS:16 nr_irqs:16 16 [2021-04-08 13:31:49.502] L2C-310 erratum 769419 enabled [2021-04-08 13:31:49.502] L2C-310 enabling early BRESP for Cortex-A9 [2021-04-08 13:31:49.502] L2C-310 full line of zeros enabled for Cortex-A9 [2021-04-08 13:31:49.502] L2C-310 ID prefetch enabled, offset 16 lines [2021-04-08 13:31:49.502] L2C-310 dynamic clock gating enabled, standby mode enabled [2021-04-08 13:31:49.502] L2C-310 cache controller enabled, 16 ways, 512 kB [2021-04-08 13:31:49.502] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [2021-04-08 13:31:49.502] mxc_clocksource_init 3000000 [2021-04-08 13:31:49.502] Switching to timer-based delay loop, resolution 333ns [2021-04-08 13:31:49.502] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [2021-04-08 13:31:49.502] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [2021-04-08 13:31:49.502] Console: colour dummy device 80x30 [2021-04-08 13:31:49.502] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [2021-04-08 13:31:49.502] pid_max: default: 32768 minimum: 301 [2021-04-08 13:31:49.502] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:31:49.502] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:31:49.502] CPU: Testing write buffer coherency: ok [2021-04-08 13:31:49.515] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [2021-04-08 13:31:49.515] Setting up static identity map for 0x10008280 - 0x100082f0 [2021-04-08 13:31:49.515] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [2021-04-08 13:31:49.515] Brought up 2 CPUs [2021-04-08 13:31:49.516] SMP: Total of 2 processors activated (12.00 BogoMIPS). [2021-04-08 13:31:49.516] CPU: All CPU(s) started in SVC mode. [2021-04-08 13:31:49.516] devtmpfs: initialized [2021-04-08 13:31:49.516] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [2021-04-08 13:31:49.516] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [2021-04-08 13:31:49.516] pinctrl core: initialized pinctrl subsystem [2021-04-08 13:31:49.516] NET: Registered protocol family 16 [2021-04-08 13:31:49.516] DMA: preallocated 256 KiB pool for atomic coherent allocations [2021-04-08 13:31:49.516] cpuidle: using governor ladder [2021-04-08 13:31:49.516] cpuidle: using governor menu [2021-04-08 13:31:49.516] CPU identified as i.MX6DL, silicon rev 1.2 [2021-04-08 13:31:49.516] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [2021-04-08 13:31:49.516] hw-breakpoint: maximum watchpoint size is 4 bytes. [2021-04-08 13:31:49.516] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [2021-04-08 13:31:49.743] mxs-dma 110000.dma-apbh: initialized [2021-04-08 13:31:49.743] SCSI subsystem initialized [2021-04-08 13:31:49.743] usbcore: registered new interface driver usbfs [2021-04-08 13:31:49.743] usbcore: registered new interface driver hub [2021-04-08 13:31:49.743] usbcore: registered new device driver usb [2021-04-08 13:31:49.743] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator [2021-04-08 13:31:49.743] 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator [2021-04-08 13:31:49.743] i2c i2c-0: IMX I2C adapter registered [2021-04-08 13:31:49.743] i2c i2c-0: can't use DMA [2021-04-08 13:31:49.743] i2c i2c-1: IMX I2C adapter registered [2021-04-08 13:31:49.743] i2c i2c-1: can't use DMA [2021-04-08 13:31:49.743] i2c i2c-2: IMX I2C adapter registered [2021-04-08 13:31:49.743] i2c i2c-2: can't use DMA [2021-04-08 13:31:49.743] Linux video capture interface: v2.00 [2021-04-08 13:31:49.743] pps_core: LinuxPPS API ver. 1 registered [2021-04-08 13:31:49.743] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [2021-04-08 13:31:49.743] PTP clock support registered [2021-04-08 13:31:49.743] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [2021-04-08 13:31:49.743] Advanced Linux Sound Architecture Driver Initialized. [2021-04-08 13:31:49.743] Switched to clocksource mxc_timer1 [2021-04-08 13:31:49.743] NET: Registered protocol family 2 [2021-04-08 13:31:49.743] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [2021-04-08 13:31:49.743] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [2021-04-08 13:31:49.760] TCP: Hash tables configured (established 8192 bind 8192) [2021-04-08 13:31:49.760] UDP hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:31:49.760] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:31:49.760] NET: Registered protocol family 1 [2021-04-08 13:31:49.760] RPC: Registered named UNIX socket transport module. [2021-04-08 13:31:49.760] RPC: Registered udp transport module. [2021-04-08 13:31:49.760] RPC: Registered tcp transport module. [2021-04-08 13:31:49.760] RPC: Registered tcp NFSv4.1 backchannel transport module. [2021-04-08 13:31:49.760] Trying to unpack rootfs image as initramfs... [2021-04-08 13:31:49.760] Freeing initrd memory: 8392K (82c00000 - 83432000) [2021-04-08 13:31:49.760] CPU PMU: Failed to parse /soc/pmu/interrupt-affinity[0] [2021-04-08 13:31:49.760] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [2021-04-08 13:31:49.760] imx rpmsg driver is registered. [2021-04-08 13:31:49.760] Bus freq driver module loaded [2021-04-08 13:31:49.760] futex hash table entries: 512 (order: 3, 32768 bytes) [2021-04-08 13:31:49.760] VFS: Disk quotas dquot_6.6.0 [2021-04-08 13:31:49.760] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [2021-04-08 13:31:49.760] NFS: Registering the id_resolver key type [2021-04-08 13:31:49.760] Key type id_resolver registered [2021-04-08 13:31:49.760] Key type id_legacy registered [2021-04-08 13:31:49.760] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [2021-04-08 13:31:49.779] fuse init (API version 7.23) [2021-04-08 13:31:49.779] io scheduler noop registered [2021-04-08 13:31:49.779] io scheduler deadline registered [2021-04-08 13:31:49.779] io scheduler cfq registered (default) [2021-04-08 13:31:49.779] imx-weim 21b8000.weim: Driver registered. [2021-04-08 13:31:49.779] backlight supply power not found, using dummy regulator [2021-04-08 13:31:49.779] mxc_sdc_fb fb@0: NO mxc display driver found! [2021-04-08 13:31:49.779] mxc_sdc_fb fb@1: NO mxc display driver found! [2021-04-08 13:31:49.779] imx-sdma 20ec000.sdma: no iram assigned, using external mem [2021-04-08 13:31:49.779] imx-sdma 20ec000.sdma: no event needs to be remapped [2021-04-08 13:31:49.779] imx-sdma 20ec000.sdma: initialized [2021-04-08 13:31:49.779] pfuze100-regulator 1-0008: unrecognized pfuze chip ID! [2021-04-08 13:31:49.779] imx-sdma 20ec000.sdma: loaded firmware 3.3 [2021-04-08 13:31:49.779] pfuze100-regulator: probe of 1-0008 failed with error -5 [2021-04-08 13:31:49.779] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [2021-04-08 13:31:49.779] console [ttymxc0] enabled [2021-04-08 13:31:49.779] imx sema4 driver is registered. [2021-04-08 13:31:49.779] [drm] Initialized drm 1.1.0 20060810 [2021-04-08 13:31:49.779] [drm] Initialized vivante 1.0.0 20120216 on minor 0 [2021-04-08 13:31:49.779] brd: module loaded [2021-04-08 13:31:49.788] loop: module loaded [2021-04-08 13:31:49.788] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 0, 0 [2021-04-08 13:31:49.788] spi_imx 2008000.ecspi: probed [2021-04-08 13:31:49.788] 2188000.ethernet supply phy not found, using dummy regulator [2021-04-08 13:31:50.013] pps pps0: new PPS source ptp0 [2021-04-08 13:31:50.013] fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 [2021-04-08 13:31:50.013] fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 1a:a2:3e:77:83:a3 [2021-04-08 13:31:50.013] libphy: fec_enet_mii_bus: probed [2021-04-08 13:31:50.013] fec 2188000.ethernet eth0: registered PHC device 0 [2021-04-08 13:31:50.013] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [2021-04-08 13:31:50.013] ehci-mxc: Freescale On-Chip EHCI Host driver [2021-04-08 13:31:50.013] usbcore: registered new interface driver usb-storage [2021-04-08 13:31:50.013] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator [2021-04-08 13:31:50.013] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:31:50.013] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.013] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:31:50.013] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.013] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers [2021-04-08 13:31:50.013] mousedev: PS/2 mouse device common for all mice [2021-04-08 13:31:50.013] egalax_ts 1-0004: Failed to read firmware version [2021-04-08 13:31:50.027] egalax_ts: probe of 1-0004 failed with error -5 [2021-04-08 13:31:50.027] egalax_ts 2-0004: Failed to read firmware version [2021-04-08 13:31:50.027] egalax_ts: probe of 2-0004 failed with error -5 [2021-04-08 13:31:50.027] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0 [2021-04-08 13:31:50.027] i2c /dev entries driver [2021-04-08 13:31:50.027] IR NEC protocol handler initialized [2021-04-08 13:31:50.027] IR RC5(x/sz) protocol handler initialized [2021-04-08 13:31:50.027] IR RC6 protocol handler initialized [2021-04-08 13:31:50.027] IR JVC protocol handler initialized [2021-04-08 13:31:50.027] IR Sony protocol handler initialized [2021-04-08 13:31:50.027] IR SANYO protocol handler initialized [2021-04-08 13:31:50.027] IR Sharp protocol handler initialized [2021-04-08 13:31:50.027] IR MCE Keyboard/mouse protocol handler initialized [2021-04-08 13:31:50.027] IR XMP protocol handler initialized [2021-04-08 13:31:50.027] imx2-wdt 20c0000.wdog: use WDOG_B to reboot. [2021-04-08 13:31:50.027] imx2-wdt 20c0000.wdog: timeout 60 sec (nowayout=0) [2021-04-08 13:31:50.027] sdhci: Secure Digital Host Controller Interface driver [2021-04-08 13:31:50.027] sdhci: Copyright(c) Pierre Ossman [2021-04-08 13:31:50.027] sdhci-pltfm: SDHCI platform and OF driver helper [2021-04-08 13:31:50.027] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified [2021-04-08 13:31:50.027] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [2021-04-08 13:31:50.035] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [2021-04-08 13:31:50.035] sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found [2021-04-08 13:31:50.035] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found [2021-04-08 13:31:50.039] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [2021-04-08 13:31:50.076] /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified [2021-04-08 13:31:50.076] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [2021-04-08 13:31:50.076] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [2021-04-08 13:31:50.076] sdhci-esdhc-imx 2198000.usdhc: No vmmc regulator found [2021-04-08 13:31:50.076] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [2021-04-08 13:31:50.149] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [2021-04-08 13:31:50.149] /soc/aips-bus@02100000/usdhc@0219c000: voltage-ranges unspecified [2021-04-08 13:31:50.150] sdhci-esdhc-imx 219c000.usdhc: No vmmc regulator found [2021-04-08 13:31:50.150] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [2021-04-08 13:31:50.179] mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [2021-04-08 13:31:50.366] mxc_vpu 2040000.vpu_fsl: VPU initialized [2021-04-08 13:31:50.366] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [2021-04-08 13:31:50.366] usbcore: registered new interface driver usbhid [2021-04-08 13:31:50.366] usbhid: USB HID core driver [2021-04-08 13:31:50.366] wm8962 0-001a: Failed to read ID register [2021-04-08 13:31:50.366] wm8962: probe of 0-001a failed with error -5 [2021-04-08 13:31:50.366] imx-wm8962 sound: failed to find codec platform device [2021-04-08 13:31:50.366] imx-wm8962: probe of sound failed with error -22 [2021-04-08 13:31:50.366] NET: Registered protocol family 10 [2021-04-08 13:31:50.366] sit: IPv6 over IPv4 tunneling driver [2021-04-08 13:31:50.366] NET: Registered protocol family 17 [2021-04-08 13:31:50.366] Key type dns_resolver registered [2021-04-08 13:31:50.366] cpu cpu0: failed to get regulators [2021-04-08 13:31:50.366] imx6q-cpufreq: probe of imx6q-cpufreq.0 failed with error -2 [2021-04-08 13:31:50.366] Registering SWP/SWPB emulation handler [2021-04-08 13:31:50.366] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:31:50.366] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.366] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:31:50.366] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.366] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [2021-04-08 13:31:50.377] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0) [2021-04-08 13:31:50.377] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:31:50.377] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.377] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:31:50.377] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:31:50.397] mipi_dsi_pwr_on: disabling [2021-04-08 13:31:50.397] hdmi-5v-supply: disabling [2021-04-08 13:31:50.397] sensor-supply: disabling [2021-04-08 13:31:50.397] wm8962-supply: disabling [2021-04-08 13:31:50.397] usb_h1_vbus: disabling [2021-04-08 13:31:50.397] usb_otg_vbus: disabling [2021-04-08 13:31:50.397] ALSA device list: [2021-04-08 13:31:50.397] No soundcards found. [2021-04-08 13:31:50.397] Freeing unused kernel memory: 384K (80922000 - 80982000) [2021-04-08 13:31:50.438] Starting UTP [2021-04-08 13:31:50.438] uuc 0.5 [built Sep 16 2016 02:36:28] [2021-04-08 13:31:50.438] UTP: Waiting for device to appear [2021-04-08 13:31:52.244] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:54.339] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:56.417] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:31:58.530] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:32:38.570] [2021-04-08 13:32:38.570] [2021-04-08 13:32:38.570] U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1bf9f (Apr 07 2021 - 17:37:04 +0530) [2021-04-08 13:32:38.570] [2021-04-08 13:32:38.570] CPU: Freescale i.MX6DL rev1.2 at 792MHz [2021-04-08 13:32:38.570] CPU: Automotive temperature grade (-40C to 125C) at 42C [2021-04-08 13:32:38.570] Reset cause: POR [2021-04-08 13:32:38.570] Model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:32:38.570] Board: MX6-SabreSD [2021-04-08 13:32:38.571] DRAM: 1 GiB [2021-04-08 13:32:38.633] MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 [2021-04-08 13:32:38.671] MMC: no card present [2021-04-08 13:32:38.671] mmc_init: -123, time 2 [2021-04-08 13:32:38.671] *** Warning - MMC init failed, using default environment [2021-04-08 13:32:38.671] [2021-04-08 13:32:38.671] No panel detected: default to Hannstar-XGA [2021-04-08 13:32:38.671] Display: Hannstar-XGA (1024x768) [2021-04-08 13:32:38.776] In: serial [2021-04-08 13:32:38.776] Out: serial [2021-04-08 13:32:38.776] Err: serial [2021-04-08 13:32:38.776] MMC: no card present [2021-04-08 13:32:38.776] mmc_init: -123, time 2 [2021-04-08 13:32:38.776] Net: No ethernet found. [2021-04-08 13:32:38.776] Boot from USB for mfgtools [2021-04-08 13:32:38.776] Use default environment for mfgtools [2021-04-08 13:32:38.776] Run bootcmd_mfg: run mfgtool_args; if test ${tee} = yes; then bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; else bootz ${loadaddr} ${initrd_addr} ${fdt_addr}; fi; [2021-04-08 13:32:38.776] Hit any key to stop autoboot: 0 [2021-04-08 13:32:38.776] Kernel image @ 0x12000000 [ 0x000000 - 0x554130 ] [2021-04-08 13:32:38.776] ## Loading init Ramdisk from Legacy Image at 12c00000 ... [2021-04-08 13:32:38.776] Image Name: fsl-image-mfgtool-initramfs-imx6 [2021-04-08 13:32:38.776] Image Type: ARM Linux RAMDisk Image (gzip compressed) [2021-04-08 13:32:38.776] Data Size: 8591032 Bytes = 8.2 MiB [2021-04-08 13:32:38.776] Load Address: 00000000 [2021-04-08 13:32:38.776] Entry Point: 00000000 [2021-04-08 13:32:38.776] Verifying Checksum ... OK [2021-04-08 13:32:38.857] ## Flattened Device Tree blob at 18000000 [2021-04-08 13:32:38.884] Booting using the fdt blob at 0x18000000 [2021-04-08 13:32:38.884] Using Device Tree in place at 18000000, end 1800e4f1 [2021-04-08 13:32:38.884] No PMIC found! [2021-04-08 13:32:38.884] [2021-04-08 13:32:38.884] Starting kernel ... [2021-04-08 13:32:38.884] [2021-04-08 13:32:40.546] Booting Linux on physical CPU 0x0 [2021-04-08 13:32:40.546] Linux version 4.1.15+ (bamboo@yb6) (gcc version 5.3.0 (GCC) ) #1 SMP PREEMPT Fri Sep 16 18:10:49 CDT 2016 [2021-04-08 13:32:40.546] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [2021-04-08 13:32:40.546] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [2021-04-08 13:32:40.546] Machine model: Freescale i.MX6 DualLite SABRE Smart Device Board [2021-04-08 13:32:40.546] Reserved memory: created CMA memory pool at 0x3c000000, size 320 MiB [2021-04-08 13:32:40.546] Reserved memory: initialized node linux,cma, compatible id shared-dma-pool [2021-04-08 13:32:40.546] Memory policy: Data cache writealloc [2021-04-08 13:32:40.546] PERCPU: Embedded 12 pages/cpu @ab71c000 s16716 r8192 d24244 u49152 [2021-04-08 13:32:40.546] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [2021-04-08 13:32:40.546] Kernel command line: console=ttymxc0,115200 rdinit=/linuxrc g_mass_storage.stall=0 g_mass_storage.removable=1 g_mass_storage.file=/fat g_mass_storage.ro=1 g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF g_mass_storage.iSerialNumber= enable_wait_mode=off [2021-04-08 13:32:40.546] PID hash table entries: 4096 (order: 2, 16384 bytes) [2021-04-08 13:32:40.546] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [2021-04-08 13:32:40.556] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [2021-04-08 13:32:40.556] Memory: 692096K/1048576K available (6903K kernel code, 320K rwdata, 2416K rodata, 384K init, 423K bss, 28800K reserved, 327680K cma-reserved, 0K highmem) [2021-04-08 13:32:40.556] Virtual kernel memory layout: [2021-04-08 13:32:40.556] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [2021-04-08 13:32:40.556] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [2021-04-08 13:32:40.556] vmalloc : 0xc0800000 - 0xff000000 (1000 MB) [2021-04-08 13:32:40.556] lowmem : 0x80000000 - 0xc0000000 (1024 MB) [2021-04-08 13:32:40.556] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [2021-04-08 13:32:40.556] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [2021-04-08 13:32:40.556] .text : 0x80008000 - 0x80921fd8 (9320 kB) [2021-04-08 13:32:40.556] .init : 0x80922000 - 0x80982000 ( 384 kB) [2021-04-08 13:32:40.556] .data : 0x80982000 - 0x809d2080 ( 321 kB) [2021-04-08 13:32:40.556] .bss : 0x809d5000 - 0x80a3ee54 ( 424 kB) [2021-04-08 13:32:40.556] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [2021-04-08 13:32:40.556] Preemptible hierarchical RCU implementation. [2021-04-08 13:32:40.556] Additional per-CPU info printed with stalls. [2021-04-08 13:32:40.556] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [2021-04-08 13:32:40.575] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [2021-04-08 13:32:40.575] NR_IRQS:16 nr_irqs:16 16 [2021-04-08 13:32:40.575] L2C-310 erratum 769419 enabled [2021-04-08 13:32:40.575] L2C-310 enabling early BRESP for Cortex-A9 [2021-04-08 13:32:40.575] L2C-310 full line of zeros enabled for Cortex-A9 [2021-04-08 13:32:40.575] L2C-310 ID prefetch enabled, offset 16 lines [2021-04-08 13:32:40.575] L2C-310 dynamic clock gating enabled, standby mode enabled [2021-04-08 13:32:40.575] L2C-310 cache controller enabled, 16 ways, 512 kB [2021-04-08 13:32:40.575] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [2021-04-08 13:32:40.575] mxc_clocksource_init 3000000 [2021-04-08 13:32:40.575] Switching to timer-based delay loop, resolution 333ns [2021-04-08 13:32:40.575] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [2021-04-08 13:32:40.575] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [2021-04-08 13:32:40.575] Console: colour dummy device 80x30 [2021-04-08 13:32:40.575] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [2021-04-08 13:32:40.575] pid_max: default: 32768 minimum: 301 [2021-04-08 13:32:40.575] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:32:40.575] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [2021-04-08 13:32:40.575] CPU: Testing write buffer coherency: ok [2021-04-08 13:32:40.591] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [2021-04-08 13:32:40.591] Setting up static identity map for 0x10008280 - 0x100082f0 [2021-04-08 13:32:40.591] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [2021-04-08 13:32:40.591] Brought up 2 CPUs [2021-04-08 13:32:40.591] SMP: Total of 2 processors activated (12.00 BogoMIPS). [2021-04-08 13:32:40.591] CPU: All CPU(s) started in SVC mode. [2021-04-08 13:32:40.591] devtmpfs: initialized [2021-04-08 13:32:40.591] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [2021-04-08 13:32:40.591] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [2021-04-08 13:32:40.592] pinctrl core: initialized pinctrl subsystem [2021-04-08 13:32:40.592] NET: Registered protocol family 16 [2021-04-08 13:32:40.592] DMA: preallocated 256 KiB pool for atomic coherent allocations [2021-04-08 13:32:40.592] cpuidle: using governor ladder [2021-04-08 13:32:40.592] cpuidle: using governor menu [2021-04-08 13:32:40.592] CPU identified as i.MX6DL, silicon rev 1.2 [2021-04-08 13:32:40.592] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [2021-04-08 13:32:40.592] hw-breakpoint: maximum watchpoint size is 4 bytes. [2021-04-08 13:32:40.592] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [2021-04-08 13:32:40.822] mxs-dma 110000.dma-apbh: initialized [2021-04-08 13:32:40.822] SCSI subsystem initialized [2021-04-08 13:32:40.822] usbcore: registered new interface driver usbfs [2021-04-08 13:32:40.822] usbcore: registered new interface driver hub [2021-04-08 13:32:40.822] usbcore: registered new device driver usb [2021-04-08 13:32:40.822] 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator [2021-04-08 13:32:40.822] 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator [2021-04-08 13:32:40.822] i2c i2c-0: IMX I2C adapter registered [2021-04-08 13:32:40.822] i2c i2c-0: can't use DMA [2021-04-08 13:32:40.822] i2c i2c-1: IMX I2C adapter registered [2021-04-08 13:32:40.822] i2c i2c-1: can't use DMA [2021-04-08 13:32:40.822] i2c i2c-2: IMX I2C adapter registered [2021-04-08 13:32:40.822] i2c i2c-2: can't use DMA [2021-04-08 13:32:40.822] Linux video capture interface: v2.00 [2021-04-08 13:32:40.822] pps_core: LinuxPPS API ver. 1 registered [2021-04-08 13:32:40.822] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [2021-04-08 13:32:40.822] PTP clock support registered [2021-04-08 13:32:40.822] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [2021-04-08 13:32:40.822] Advanced Linux Sound Architecture Driver Initialized. [2021-04-08 13:32:40.822] Switched to clocksource mxc_timer1 [2021-04-08 13:32:40.822] NET: Registered protocol family 2 [2021-04-08 13:32:40.822] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [2021-04-08 13:32:40.822] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [2021-04-08 13:32:40.838] TCP: Hash tables configured (established 8192 bind 8192) [2021-04-08 13:32:40.838] UDP hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:32:40.838] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [2021-04-08 13:32:40.838] NET: Registered protocol family 1 [2021-04-08 13:32:40.838] RPC: Registered named UNIX socket transport module. [2021-04-08 13:32:40.838] RPC: Registered udp transport module. [2021-04-08 13:32:40.838] RPC: Registered tcp transport module. [2021-04-08 13:32:40.838] RPC: Registered tcp NFSv4.1 backchannel transport module. [2021-04-08 13:32:40.838] Trying to unpack rootfs image as initramfs... [2021-04-08 13:32:40.838] Freeing initrd memory: 8392K (82c00000 - 83432000) [2021-04-08 13:32:40.838] CPU PMU: Failed to parse /soc/pmu/interrupt-affinity[0] [2021-04-08 13:32:40.838] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [2021-04-08 13:32:40.838] imx rpmsg driver is registered. [2021-04-08 13:32:40.838] Bus freq driver module loaded [2021-04-08 13:32:40.838] futex hash table entries: 512 (order: 3, 32768 bytes) [2021-04-08 13:32:40.838] VFS: Disk quotas dquot_6.6.0 [2021-04-08 13:32:40.838] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [2021-04-08 13:32:40.838] NFS: Registering the id_resolver key type [2021-04-08 13:32:40.838] Key type id_resolver registered [2021-04-08 13:32:40.838] Key type id_legacy registered [2021-04-08 13:32:40.838] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [2021-04-08 13:32:40.856] fuse init (API version 7.23) [2021-04-08 13:32:40.856] io scheduler noop registered [2021-04-08 13:32:40.856] io scheduler deadline registered [2021-04-08 13:32:40.856] io scheduler cfq registered (default) [2021-04-08 13:32:40.856] imx-weim 21b8000.weim: Driver registered. [2021-04-08 13:32:40.856] backlight supply power not found, using dummy regulator [2021-04-08 13:32:40.857] mxc_sdc_fb fb@0: NO mxc display driver found! [2021-04-08 13:32:40.857] mxc_sdc_fb fb@1: NO mxc display driver found! [2021-04-08 13:32:40.857] imx-sdma 20ec000.sdma: no iram assigned, using external mem [2021-04-08 13:32:40.857] imx-sdma 20ec000.sdma: no event needs to be remapped [2021-04-08 13:32:40.857] imx-sdma 20ec000.sdma: initialized [2021-04-08 13:32:40.857] pfuze100-regulator 1-0008: unrecognized pfuze chip ID! [2021-04-08 13:32:40.857] imx-sdma 20ec000.sdma: loaded firmware 3.3 [2021-04-08 13:32:40.857] pfuze100-regulator: probe of 1-0008 failed with error -5 [2021-04-08 13:32:40.857] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [2021-04-08 13:32:40.857] console [ttymxc0] enabled [2021-04-08 13:32:40.857] imx sema4 driver is registered. [2021-04-08 13:32:40.857] [drm] Initialized drm 1.1.0 20060810 [2021-04-08 13:32:40.857] [drm] Initialized vivante 1.0.0 20120216 on minor 0 [2021-04-08 13:32:40.857] brd: module loaded [2021-04-08 13:32:40.871] loop: module loaded [2021-04-08 13:32:40.871] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 0, 0 [2021-04-08 13:32:40.871] spi_imx 2008000.ecspi: probed [2021-04-08 13:32:40.871] 2188000.ethernet supply phy not found, using dummy regulator [2021-04-08 13:32:41.087] pps pps0: new PPS source ptp0 [2021-04-08 13:32:41.087] fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 [2021-04-08 13:32:41.087] fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: 36:fc:81:69:a6:65 [2021-04-08 13:32:41.087] libphy: fec_enet_mii_bus: probed [2021-04-08 13:32:41.087] fec 2188000.ethernet eth0: registered PHC device 0 [2021-04-08 13:32:41.088] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [2021-04-08 13:32:41.088] ehci-mxc: Freescale On-Chip EHCI Host driver [2021-04-08 13:32:41.088] usbcore: registered new interface driver usb-storage [2021-04-08 13:32:41.088] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator [2021-04-08 13:32:41.088] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:32:41.088] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.088] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:32:41.088] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.088] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers [2021-04-08 13:32:41.088] mousedev: PS/2 mouse device common for all mice [2021-04-08 13:32:41.088] egalax_ts 1-0004: Failed to read firmware version [2021-04-08 13:32:41.103] egalax_ts: probe of 1-0004 failed with error -5 [2021-04-08 13:32:41.103] egalax_ts 2-0004: Failed to read firmware version [2021-04-08 13:32:41.103] egalax_ts: probe of 2-0004 failed with error -5 [2021-04-08 13:32:41.104] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0 [2021-04-08 13:32:41.104] i2c /dev entries driver [2021-04-08 13:32:41.104] IR NEC protocol handler initialized [2021-04-08 13:32:41.104] IR RC5(x/sz) protocol handler initialized [2021-04-08 13:32:41.104] IR RC6 protocol handler initialized [2021-04-08 13:32:41.104] IR JVC protocol handler initialized [2021-04-08 13:32:41.104] IR Sony protocol handler initialized [2021-04-08 13:32:41.104] IR SANYO protocol handler initialized [2021-04-08 13:32:41.104] IR Sharp protocol handler initialized [2021-04-08 13:32:41.104] IR MCE Keyboard/mouse protocol handler initialized [2021-04-08 13:32:41.104] IR XMP protocol handler initialized [2021-04-08 13:32:41.104] imx2-wdt 20c0000.wdog: use WDOG_B to reboot. [2021-04-08 13:32:41.104] imx2-wdt 20c0000.wdog: timeout 60 sec (nowayout=0) [2021-04-08 13:32:41.104] sdhci: Secure Digital Host Controller Interface driver [2021-04-08 13:32:41.104] sdhci: Copyright(c) Pierre Ossman [2021-04-08 13:32:41.104] sdhci-pltfm: SDHCI platform and OF driver helper [2021-04-08 13:32:41.104] /soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified [2021-04-08 13:32:41.104] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO [2021-04-08 13:32:41.119] sdhci-esdhc-imx 2194000.usdhc: Got WP GPIO [2021-04-08 13:32:41.119] sdhci-esdhc-imx 2194000.usdhc: No vmmc regulator found [2021-04-08 13:32:41.119] sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found [2021-04-08 13:32:41.122] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [2021-04-08 13:32:41.154] /soc/aips-bus@02100000/usdhc@02198000: voltage-ranges unspecified [2021-04-08 13:32:41.154] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [2021-04-08 13:32:41.154] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [2021-04-08 13:32:41.154] sdhci-esdhc-imx 2198000.usdhc: No vmmc regulator found [2021-04-08 13:32:41.154] sdhci-esdhc-imx 2198000.usdhc: No vqmmc regulator found [2021-04-08 13:32:41.229] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [2021-04-08 13:32:41.229] /soc/aips-bus@02100000/usdhc@0219c000: voltage-ranges unspecified [2021-04-08 13:32:41.229] sdhci-esdhc-imx 219c000.usdhc: No vmmc regulator found [2021-04-08 13:32:41.229] sdhci-esdhc-imx 219c000.usdhc: No vqmmc regulator found [2021-04-08 13:32:41.260] mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [2021-04-08 13:32:41.444] mxc_vpu 2040000.vpu_fsl: VPU initialized [2021-04-08 13:32:41.444] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [2021-04-08 13:32:41.444] usbcore: registered new interface driver usbhid [2021-04-08 13:32:41.444] usbhid: USB HID core driver [2021-04-08 13:32:41.444] wm8962 0-001a: Failed to read ID register [2021-04-08 13:32:41.444] wm8962: probe of 0-001a failed with error -5 [2021-04-08 13:32:41.444] imx-wm8962 sound: failed to find codec platform device [2021-04-08 13:32:41.444] imx-wm8962: probe of sound failed with error -22 [2021-04-08 13:32:41.444] NET: Registered protocol family 10 [2021-04-08 13:32:41.444] sit: IPv6 over IPv4 tunneling driver [2021-04-08 13:32:41.444] NET: Registered protocol family 17 [2021-04-08 13:32:41.444] Key type dns_resolver registered [2021-04-08 13:32:41.444] cpu cpu0: failed to get regulators [2021-04-08 13:32:41.444] imx6q-cpufreq: probe of imx6q-cpufreq.0 failed with error -2 [2021-04-08 13:32:41.444] Registering SWP/SWPB emulation handler [2021-04-08 13:32:41.444] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:32:41.444] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.444] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:32:41.444] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.444] input: gpio-keys as /devices/soc0/gpio-keys/input/input2 [2021-04-08 13:32:41.458] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:00 UTC (0) [2021-04-08 13:32:41.458] reg-fixed-voltage regulators:regulator@0: Failed to resolve vin-supply for usb_otg_vbus [2021-04-08 13:32:41.458] imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.458] reg-fixed-voltage regulators:regulator@1: Failed to resolve vin-supply for usb_h1_vbus [2021-04-08 13:32:41.458] imx_usb 2184200.usb: Can't register ci_hdrc platform device, err=-517 [2021-04-08 13:32:41.477] mipi_dsi_pwr_on: disabling [2021-04-08 13:32:41.477] hdmi-5v-supply: disabling [2021-04-08 13:32:41.477] sensor-supply: disabling [2021-04-08 13:32:41.477] wm8962-supply: disabling [2021-04-08 13:32:41.477] usb_h1_vbus: disabling [2021-04-08 13:32:41.477] usb_otg_vbus: disabling [2021-04-08 13:32:41.477] ALSA device list: [2021-04-08 13:32:41.477] No soundcards found. [2021-04-08 13:32:41.477] Freeing unused kernel memory: 384K (80922000 - 80982000) [2021-04-08 13:32:41.519] Starting UTP [2021-04-08 13:32:41.519] uuc 0.5 [built Sep 16 2016 02:36:28] [2021-04-08 13:32:41.519] UTP: Waiting for device to appear [2021-04-08 13:32:43.340] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:32:45.437] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:32:47.532] mmc3: error -110 whilst initialising MMC card [2021-04-08 13:32:49.628] mmc3: error -110 whilst initialising MMC card