U-Boot SPL 2020.04-5.4.70-2.3.0+ge42dee801e (Dec 03 2020 - 22:30:26 +0000) Can't find PMIC:PCA9450 DDRINFO: start DRAM init DDRINFO: DRAM rate 3000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Trying to boot from MMC1 NOTICE: BL31: v2.2(release):imx_5.4.70_er4-1-gf1d7187f2 NOTICE: BL31: Built : 00:13:32, Dec 2 2020 E/TC:0 0 caam_mp_init:405 ************************************* E/TC:0 0 caam_mp_init:406 * Warning: Manufacturing protection * E/TC:0 0 caam_mp_init:407 * is not supported * E/TC:0 0 caam_mp_init:408 ************************************* U-Boot 2020.04-5.4.70-2.3.0+ge42dee801e (Dec 03 2020 - 22:30:26 +0000) CPU: i.MX8MMQ rev1.0 at 1200MHz CPU: Commercial temperature grade (0C to 95C) at 25C Reset cause: POR Model: NXP i.MX8MM EVK board DRAM: 2 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x52] Power supply on USB2 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50] MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... Run CMD11 1.8V switch OK [*]-Video Link 0Can't find cec device id=0x3c fail to probe panel device adv7535@3d failed to get any video link display timings probe video device failed, ret -22 [0] lcdif@32e00000, video [1] mipi_dsi@32e10000, video_bridge [2] adv7535@3d, panel Can't find cec device id=0x3c fail to probe panel device adv7535@3d failed to get any video link display timings probe video device failed, ret -22 In: serial Out: serial Err: serial BuildInfo: - ATF f1d7187 - U-Boot 2020.04-5.4.70-2.3.0+ge42dee801e Run CMD11 1.8V switch switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Run CMD11 1.8V switch Net: eth0: ethernet@30be0000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 Run CMD11 1.8V switch switch to partitions #0, OK mmc1 is current device Run CMD11 1.8V switch 28013056 bytes read in 341 ms (78.3 MiB/s) Booting from mmc ... 45460 bytes read in 16 ms (2.7 MiB/s) ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 0000000043000000, end 000000004300e193 Can't find cec device id=0x3c fail to probe panel device adv7535@3d failed to get any video link display timings probe video device failed, ret -22 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.70-2.3.0+g4f2631b022d8 (oe-user@oe-host) (gcc version 9.2.0 (GCC)) #1 SMP PREEMPT Wed Dec 16 10:53:09 UTC 2020 [ 0.000000] Machine model: FSL i.MX8MM LPDDR4 EVK with QCA WIFI revB board [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000078000000, size 640 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] NUMA: NODE_DATA [mem 0xbdbdd500-0xbdbdefff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000b7ffffff] [ 0.000000] node 0: [mem 0x00000000b8400000-0x00000000bdffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bdffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s58904 r8192 d31208 u98304 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 507008 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: console=ttymxc1,115200 root=/dev/mmcblk1p2 rootwait rw [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 1336024K/2060288K available (16636K kernel code, 1244K rwdata, 6556K rodata, 2880K init, 1017K bss, 68904K reserved, 655360K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 128 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x44c with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000406] Console: colour dummy device 80x25 [ 0.000475] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.000484] pid_max: default: 32768 minimum: 301 [ 0.000555] LSM: Security Framework initializing [ 0.000609] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000619] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001764] ASID allocator initialised with 32768 entries [ 0.001833] rcu: Hierarchical SRCU implementation. [ 0.002812] EFI services will not be available. [ 0.002966] smp: Bringing up secondary CPUs ... [ 0.003332] Detected VIPT I-cache on CPU1 [ 0.003356] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.003387] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.003779] Detected VIPT I-cache on CPU2 [ 0.003795] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.003812] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.004225] Detected VIPT I-cache on CPU3 [ 0.004240] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.004258] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.004317] smp: Brought up 1 node, 4 CPUs [ 0.004326] SMP: Total of 4 processors activated. [ 0.004331] CPU features: detected: 32-bit EL0 Support [ 0.004339] CPU features: detected: CRC32 instructions [ 0.010889] CPU: All CPU(s) started at EL2 [ 0.010909] alternatives: patching kernel code [ 0.012337] devtmpfs: initialized [ 0.018612] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.018630] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.034869] pinctrl core: initialized pinctrl subsystem [ 0.035577] DMI not present or invalid. [ 0.035827] NET: Registered protocol family 16 [ 0.042551] DMA: preallocated 256 KiB pool for atomic allocations [ 0.042579] audit: initializing netlink subsys (disabled) [ 0.042825] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.043679] cpuidle: using governor menu [ 0.044163] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.045015] Serial: AMBA PL011 UART driver [ 0.045071] imx mu driver is registered. [ 0.045090] imx rpmsg driver is registered. [ 0.050846] imx8mm-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.073521] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.073532] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.073537] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.073544] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.074354] cryptd: max_cpu_qlen set to 1000 [ 0.077507] ACPI: Interpreter disabled. [ 0.078362] iommu: Default domain type: Translated [ 0.078493] vgaarb: loaded [ 0.078776] SCSI subsystem initialized [ 0.079077] usbcore: registered new interface driver usbfs [ 0.079116] usbcore: registered new interface driver hub [ 0.079167] usbcore: registered new device driver usb [ 0.080387] mc: Linux media interface: v0.10 [ 0.080418] videodev: Linux video capture interface: v2.00 [ 0.080480] pps_core: LinuxPPS API ver. 1 registered [ 0.080487] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.080500] PTP clock support registered [ 0.080642] EDAC MC: Ver: 3.0.0 [ 0.081444] No BMan portals available! [ 0.081669] QMan: Allocated lookup table at (____ptrval____), entry count 65537 [ 0.081939] No QMan portals available! [ 0.082353] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree [ 0.082788] FPGA manager framework [ 0.082864] Advanced Linux Sound Architecture Driver Initialized. [ 0.083243] Bluetooth: Core ver 2.22 [ 0.083266] NET: Registered protocol family 31 [ 0.083272] Bluetooth: HCI device and connection manager initialized [ 0.083280] Bluetooth: HCI socket layer initialized [ 0.083287] Bluetooth: L2CAP socket layer initialized [ 0.083299] Bluetooth: SCO socket layer initialized [ 0.084020] clocksource: Switched to clocksource arch_sys_counter [ 0.084196] VFS: Disk quotas dquot_6.6.0 [ 0.084241] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.084395] pnp: PnP ACPI: disabled [ 0.089810] thermal_sys: Registered thermal governor 'step_wise' [ 0.089814] thermal_sys: Registered thermal governor 'power_allocator' [ 0.090133] NET: Registered protocol family 2 [ 0.090437] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.090472] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.090581] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 0.090806] TCP: Hash tables configured (established 16384 bind 16384) [ 0.090881] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.090922] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.091062] NET: Registered protocol family 1 [ 0.091375] RPC: Registered named UNIX socket transport module. [ 0.091379] RPC: Registered udp transport module. [ 0.091383] RPC: Registered tcp transport module. [ 0.091387] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.091731] PCI: CLS 0 bytes, default 64 [ 0.092398] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.092788] kvm [1]: IPA Size Limit: 40bits [ 0.093371] kvm [1]: GICv3: no GICV resource entry [ 0.093376] kvm [1]: disabling GICv2 emulation [ 0.093393] kvm [1]: GIC system register CPU interface enabled [ 0.093456] kvm [1]: vgic interrupt IRQ1 [ 0.093544] kvm [1]: Hyp mode initialized successfully [ 0.096360] Initialise system trusted keyrings [ 0.096469] workingset: timestamp_bits=44 max_order=19 bucket_order=0 [ 0.102196] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.102825] NFS: Registering the id_resolver key type [ 0.102848] Key type id_resolver registered [ 0.102852] Key type id_legacy registered [ 0.102864] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.102885] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.103235] 9p: Installing v9fs 9p2000 file system support [ 0.116429] Key type asymmetric registered [ 0.116437] Asymmetric key parser 'x509' registered [ 0.116465] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 0.116471] io scheduler mq-deadline registered [ 0.116476] io scheduler kyber registered [ 0.122082] EINJ: ACPI disabled. [ 0.130913] imx-sdma 302c0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [ 0.130927] imx-sdma 302c0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [ 0.139030] mxs-dma 33000000.dma-controller: initialized [ 0.140228] Bus freq driver module loaded [ 0.145446] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.147678] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 39, base_baud = 5000000) is a IMX [ 0.148197] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 40, base_baud = 5000000) is a IMX [ 0.148569] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 41, base_baud = 1500000) is a IMX [ 1.135148] printk: console [ttymxc1] enabled [ 1.145960] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.152597] [drm] No driver support for vblank timestamp query. [ 1.158599] imx-drm soc@0:bus@32c00000:display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 1.167878] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to get blk_ctl [ 1.174461] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 1.181480] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 1.189756] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -517 [ 1.207449] loop: module loaded [ 1.212827] imx ahci driver is registered. [ 1.220181] spi-nor spi3.0: n25q256ax1 (32768 Kbytes) [ 1.229932] libphy: Fixed MDIO Bus: probed [ 1.234809] tun: Universal TUN/TAP device driver, 1.6 [ 1.240733] thunder_xcv, ver 1.0 [ 1.243990] thunder_bgx, ver 1.0 [ 1.247260] nicpf, ver 1.0 [ 1.250870] pps pps0: new PPS source ptp0 [ 1.259997] libphy: fec_enet_mii_bus: probed [ 1.265423] fec 30be0000.ethernet eth0: registered PHC device 0 [ 1.271996] Freescale FM module, FMD API version 21.1.0 [ 1.277512] Freescale FM Ports module [ 1.281183] fsl_mac: fsl_mac: FSL FMan MAC API based driver [ 1.286936] fsl_dpa: FSL DPAA Ethernet driver [ 1.291441] fsl_advanced: FSL DPAA Advanced drivers: [ 1.296420] fsl_proxy: FSL DPAA Proxy initialization driver [ 1.302115] fsl_oh: FSL FMan Offline Parsing port driver [ 1.308410] hclge is initializing [ 1.311728] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 1.318958] hns3: Copyright (c) 2017 Huawei Corporation. [ 1.324318] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 1.331373] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 1.337160] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.342998] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.348958] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k [ 1.355924] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.361536] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.369372] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.375468] sky2: driver version 1.30 [ 1.380138] VFIO - User Level meta-driver version: 0.3 [ 1.387286] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.393836] ehci-pci: EHCI PCI platform driver [ 1.398357] ehci-platform: EHCI generic platform driver [ 1.403793] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.409998] ohci-pci: OHCI PCI platform driver [ 1.414478] ohci-platform: OHCI generic platform driver [ 1.420483] usbcore: registered new interface driver uas [ 1.425841] usbcore: registered new interface driver usb-storage [ 1.431917] usbcore: registered new interface driver usbserial_generic [ 1.438467] usbserial: USB Serial support registered for generic [ 1.444503] usbcore: registered new interface driver ftdi_sio [ 1.450273] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.457619] usbcore: registered new interface driver usb_serial_simple [ 1.464171] usbserial: USB Serial support registered for carelink [ 1.470284] usbserial: USB Serial support registered for zio [ 1.475961] usbserial: USB Serial support registered for funsoft [ 1.481991] usbserial: USB Serial support registered for flashloader [ 1.488367] usbserial: USB Serial support registered for google [ 1.494306] usbserial: USB Serial support registered for libtransistor [ 1.500853] usbserial: USB Serial support registered for vivopay [ 1.506882] usbserial: USB Serial support registered for moto_modem [ 1.513171] usbserial: USB Serial support registered for motorola_tetra [ 1.519805] usbserial: USB Serial support registered for novatel_gps [ 1.526180] usbserial: USB Serial support registered for hp4x [ 1.531947] usbserial: USB Serial support registered for suunto [ 1.537887] usbserial: USB Serial support registered for siemens_mpi [ 1.544277] usbcore: registered new interface driver usb_ehset_test [ 1.552223] imx_usb 32e40000.usb: No over current polarity defined [ 1.559765] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/soc@0:bus@30000000/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [ 1.574987] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 [ 1.581277] i2c /dev entries driver [ 1.585478] mx6s-csi 32e20000.csi1_bridge: initialising [ 1.591239] mxc_mipi-csi 32e30000.mipi_csi: 32e30000.mipi_csi supply mipi-phy not found, using dummy regulator [ 1.601450] mxc_mipi-csi 32e30000.mipi_csi: mipi csi v4l2 device registered [ 1.608423] CSI: Registered sensor subdevice: mxc_mipi-csi.0 [ 1.614108] mxc_mipi-csi 32e30000.mipi_csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 333000000 [ 1.628239] imx2-wdt 30280000.watchdog: timeout 60 sec (nowayout=0) [ 1.634841] Bluetooth: HCI UART driver ver 2.3 [ 1.639299] Bluetooth: HCI UART protocol H4 registered [ 1.644445] Bluetooth: HCI UART protocol BCSP registered [ 1.649781] Bluetooth: HCI UART protocol LL registered [ 1.654929] Bluetooth: HCI UART protocol ATH3K registered [ 1.660347] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.666709] Bluetooth: HCI UART protocol Broadcom registered [ 1.672398] Bluetooth: HCI UART protocol QCA registered [ 1.679852] sdhci: Secure Digital Host Controller Interface driver [ 1.686052] sdhci: Copyright(c) Pierre Ossman [ 1.690623] Synopsys Designware Multimedia Card Interface Driver [ 1.697302] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.703805] mmc0: CQHCI version 5.10 [ 1.707791] mmc1: CQHCI version 5.10 [ 1.711832] mmc2: CQHCI version 5.10 [ 1.747398] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [ 1.756937] ledtrig-cpu: registered to indicate activity on CPUs [ 1.764302] caam 30900000.crypto: device ID = 0x0a16040100000000 (Era 9) [ 1.771093] caam 30900000.crypto: job rings = 2, qi = 0 [ 1.809444] caam algorithms registered in /proc/crypto [ 1.819975] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto [ 1.827395] caam 30900000.crypto: registering rng-caam [ 1.833997] Device caam-keygen registered [ 1.839797] caam-snvs 30370000.caam-snvs: violation handlers armed - non-secure state [ 1.848376] usbcore: registered new interface driver usbhid [ 1.853959] usbhid: USB HID core driver [ 1.859585] No fsl,qman node [ 1.862502] Freescale USDPAA process driver [ 1.866694] fsl-usdpaa: no region found [ 1.870537] Freescale USDPAA process IRQ driver [ 1.878530] optee: probing for conduit method from DT. [ 1.883703] optee: revision 3.10 (a991c904) [ 1.885059] optee: dynamic shared memory is enabled [ 1.894466] optee: initialized driver [ 1.894870] random: fast init done [ 1.899363] galcore: clk_get vg clock failed, disable vg! [ 1.907408] Galcore version 6.4.3.p1.305572 [ 1.920133] random: crng init done [ 1.933847] mmc2: Command Queue Engine enabled [ 1.938350] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [ 1.946431] mmcblk2: mmc2:0001 DG4016 14.7 GiB [ 1.951211] mmcblk2boot0: mmc2:0001 DG4016 partition 1 4.00 MiB [ 1.957282] mmcblk2boot1: mmc2:0001 DG4016 partition 2 4.00 MiB [ 1.963975] mmcblk2rpmb: mmc2:0001 DG4016 partition 3 4.00 MiB, chardev (237:0) [ 1.972955] mmcblk2: p1 p2 [ 1.976846] [drm] Initialized vivante 1.0.0 20170808 for 38000000.gpu on minor 0 [ 1.985481] hantrodec 0 : module inserted. Major = 236 [ 1.991143] hantrodec 1 : module inserted. Major = 236 [ 1.997052] hx280enc: module inserted. Major <235> [ 2.005726] wm8524-codec audio-codec: Failed to get mute line: -517 [ 2.054323] fsl-micfil-dai 30080000.micfil: GET IRQ: 16 [ 2.059586] fsl-micfil-dai 30080000.micfil: GET IRQ: 17 [ 2.064831] fsl-micfil-dai 30080000.micfil: GET IRQ: 18 [ 2.070074] fsl-micfil-dai 30080000.micfil: GET IRQ: 19 [ 2.081703] imx-spdif sound-spdif: snd-soc-dummy-dai <-> 30090000.spdif mapping ok [ 2.089338] imx-spdif sound-spdif: ASoC: no DMI vendor name! [ 2.098174] imx-ak4458 sound-ak4458: ASoC: failed to init link ak4458: -517 [ 2.105174] imx-ak4458 sound-ak4458: snd_soc_register_card failed (-517) [ 2.112582] debugfs: Directory '30080000.micfil' with parent 'imx-audio-micfil' already present! [ 2.121453] imx-micfil sound-micfil: snd-soc-dummy-dai <-> 30080000.micfil mapping ok [ 2.129298] imx-micfil sound-micfil: ASoC: no DMI vendor name! [ 2.137427] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 2.148118] NET: Registered protocol family 26 [ 2.153148] NET: Registered protocol family 10 [ 2.158266] Segment Routing with IPv6 [ 2.162007] NET: Registered protocol family 17 [ 2.166839] Bluetooth: RFCOMM TTY layer initialized [ 2.171734] Bluetooth: RFCOMM socket layer initialized [ 2.176905] Bluetooth: RFCOMM ver 1.11 [ 2.180664] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.185982] Bluetooth: BNEP filters: protocol multicast [ 2.191215] Bluetooth: BNEP socket layer initialized [ 2.196185] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.202114] Bluetooth: HIDP socket layer initialized [ 2.207114] 8021q: 802.1Q VLAN Support v1.8 [ 2.211319] lib80211: common routines for IEEE802.11 drivers [ 2.217088] 9pnet: Installing 9P2000 support [ 2.221395] tsn generic netlink module v1 init... [ 2.226164] Key type dns_resolver registered [ 2.231364] registered taskstats version 1 [ 2.235478] Loading compiled-in X.509 certificates [ 2.261730] usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator [ 2.270543] usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator [ 2.298114] ldo6: supplied by regulator-dummy [ 2.303278] i2c i2c-0: IMX I2C adapter registered [ 2.309189] adv7511 1-003d: 1-003d supply avdd not found, using dummy regulator [ 2.316561] adv7511 1-003d: 1-003d supply dvdd not found, using dummy regulator [ 2.323914] adv7511 1-003d: 1-003d supply pvdd not found, using dummy regulator [ 2.331265] adv7511 1-003d: 1-003d supply a2vdd not found, using dummy regulator [ 2.338726] adv7511 1-003d: 1-003d supply v3p3 not found, using dummy regulator [ 2.346076] adv7511 1-003d: 1-003d supply v1p2 not found, using dummy regulator [ 2.354199] adv7511 1-003d: Probe failed. Remote port 'mipi_dsi@32e10000' disabled [ 2.363333] i2c i2c-1: IMX I2C adapter registered [ 2.369179] pca953x 2-0020: using no AI [ 2.375697] ak4458 2-0010: Failed to request supplies: -517 [ 2.381633] ak4458 2-0012: Failed to request supplies: -517 [ 2.387490] ak5558 2-0013: Failed to request supplies: -517 [ 2.393357] ak4458 2-0011: Failed to request supplies: -517 [ 2.399249] ov5640_mipi 2-003c: No sensor reset pin available [ 2.405033] ov5640_mipi 2-003c: 2-003c supply DOVDD not found, using dummy regulator [ 2.412853] ov5640_mipi 2-003c: 2-003c supply DVDD not found, using dummy regulator [ 2.420557] ov5640_mipi 2-003c: 2-003c supply AVDD not found, using dummy regulator [ 2.436319] ov5640_mipi 2-003c: Read reg error: reg=300a [ 2.441648] ov5640_mipi 2-003c: Camera is not found [ 2.446689] i2c i2c-2: IMX I2C adapter registered [ 2.452915] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 2.453042] imx6q-pcie 33800000.pcie: 33800000.pcie supply epdev_on not found, using dummy regulator [ 2.459617] [drm] No driver support for vblank timestamp query. [ 2.468985] imx6q-pcie 33800000.pcie: PLL REF_CLK is used!. [ 2.474693] imx-drm soc@0:bus@32c00000:display-subsystem: bound imx-lcdif-crtc.0 (ops lcdif_crtc_ops) [ 2.489513] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to get blk_ctl [ 2.496079] imx_sec_dsim_drv 32e10000.mipi_dsi: version number is 0x1060200 [ 2.503086] imx_sec_dsim_drv 32e10000.mipi_dsi: Failed to attach bridge: 32e10000.mipi_dsi [ 2.508386] imx6q-pcie 33800000.pcie: PCIe PLL locked after 20 us. [ 2.511363] imx_sec_dsim_drv 32e10000.mipi_dsi: failed to bind sec dsim bridge: -19 [ 2.517578] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: [ 2.525205] imx-drm soc@0:bus@32c00000:display-subsystem: bound 32e10000.mipi_dsi (ops imx_sec_dsim_ops) [ 2.532438] imx6q-pcie 33800000.pcie: IO 0x1ff80000..0x1ff8ffff -> 0x00000000 [ 2.542414] [drm] Initialized imx-drm 1.0.0 20120507 for soc@0:bus@32c00000:display-subsystem on minor 1 [ 2.549307] imx6q-pcie 33800000.pcie: MEM 0x18000000..0x1fefffff -> 0x18000000 [ 2.559505] imx_usb 32e40000.usb: No over current polarity defined [ 2.572440] imx_usb 32e40000.usb: 32e40000.usb supply vbus not found, using dummy regulator [ 2.586046] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 3 mkt segment 0 supported-hw 0x8 0x1 [ 2.598948] mmc0: CQHCI version 5.10 [ 2.602606] sdhci-esdhc-imx 30b40000.mmc: allocated mmc-pwrseq [ 2.640143] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA [ 2.648387] mmc1: CQHCI version 5.10 [ 2.652033] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [ 2.689479] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 2.699311] debugfs: Directory '30020000.sai' with parent 'bt-sco-audio' already present! [ 2.707649] asoc-simple-card sound-bt-sco: bt-sco-pcm-wb <-> 30020000.sai mapping ok [ 2.715432] asoc-simple-card sound-bt-sco: ASoC: no DMI vendor name! [ 2.721868] debugfs: File 'Playback' in directory 'dapm' already present! [ 2.728687] debugfs: File 'Capture' in directory 'dapm' already present! [ 2.737147] mmc0: queuing unknown CIS tuple 0x01 (3 bytes) [ 2.744191] debugfs: Directory '30030000.sai' with parent 'wm8524-audio' already present! [ 2.752523] asoc-simple-card sound-wm8524: wm8524-hifi <-> 30030000.sai mapping ok [ 2.760133] asoc-simple-card sound-wm8524: ASoC: no DMI vendor name! [ 2.773430] mmc0: queuing unknown CIS tuple 0x1a (5 bytes) [ 2.778978] imx-ak4458 sound-ak4458: ASoC: failed to init link ak4458: -517 [ 2.785971] imx-ak4458 sound-ak4458: snd_soc_register_card failed (-517) [ 2.795473] mmc0: queuing unknown CIS tuple 0x1b (8 bytes) [ 2.801210] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.809948] OF: graph: no port node found in /soc@0/bus@30800000/i2c@30a30000/tcpc@50/connector [ 2.818673] mmc0: queuing unknown CIS tuple 0x14 (0 bytes) [ 2.840219] mmc0: queuing unknown CIS tuple 0x80 (1 bytes) [ 2.845766] mmc0: queuing unknown CIS tuple 0x81 (1 bytes) [ 2.851313] mmc0: queuing unknown CIS tuple 0x82 (1 bytes) [ 2.856848] mmc0: new ultra high speed SDR104 SDIO card at address 0001 [ 3.178954] ak4458 2-0010: ASoC: failed to probe component -6 [ 3.184813] imx-ak4458 sound-ak4458: ASoC: failed to instantiate card -6 [ 3.191591] imx-ak4458 sound-ak4458: snd_soc_register_card failed (-6) [ 3.200260] input: bd718xx-pwrkey as /devices/platform/soc@0/soc@0:bus@30800000/30a20000.i2c/i2c-0/0-004b/gpio-keys.1.auto/input/input1 [ 3.213239] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:01 UTC (1) [ 3.222716] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.230483] mmc1: host does not support reading read-only switch, assuming write-enable [ 3.242350] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.249124] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.257763] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 3.261863] ALSA device list: [ 3.268491] #0: imx-spdif [ 3.271286] #1: imx-audio-micfil [ 3.274695] #2: bt-sco-audio [ 3.277769] #3: wm8524-audio [ 3.365930] mmc1: new ultra high speed SDR104 SDHC card at address 59b4 [ 3.373712] mmcblk1: mmc1:59b4 USDU1 7.31 GiB [ 3.379992] mmcblk1: p1 p2 [ 3.569140] imx6q-pcie 33800000.pcie: Phy link never came up [ 3.574846] imx6q-pcie 33800000.pcie: failed to initialize host [ 3.580790] imx6q-pcie 33800000.pcie: unable to add pcie port. [ 3.687571] EXT4-fs (mmcblk1p2): recovery complete [ 3.698151] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.706327] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 3.713170] devtmpfs: mounted [ 3.716933] Freeing unused kernel memory: 2880K [ 3.721515] Run /sbin/init as init process [ 3.872961] systemd[1]: System time before build time, advancing clock. [ 3.894215] systemd[1]: systemd 243.2+ running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 3.916169] systemd[1]: Detected architecture arm64. Welcome to NXP i.MX Release Distro 5.4-zeus (zeus)! [ 3.969781] systemd[1]: Set hostname to . [ 4.156359] systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket ??/run/dbus/system_bus_socket; please update the unit file accordingly. [ 4.183339] systemd[1]: /lib/systemd/system/syslogd.service:8: PIDFile= references a path below legacy directory /var/run/, updating /var/run/syslogd.pid ??/run/syslogd.pid; please update the unit file accordingly. [ 4.210143] systemd[1]: /lib/systemd/system/rpcbind.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/rpcbind.sock ??/run/rpcbind.sock; please update the unit file accordingly. [ 4.233408] systemd[1]: /lib/systemd/system/klogd.service:8: PIDFile= references a path below legacy directory /var/run/, updating /var/run/klogd.pid ??/run/klogd.pid; please update the unit file accordingly. [ 4.330627] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 4.343119] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 4.353631] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ OK ] Started Dispatch Password ?¦ts to Console Directory Watch. [ OK ] Started Forward Password R?¦uests to Wall Directory Watch. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Paths. [ OK ] Reached target Remote File Systems. [ OK ] Reached target Slices. [ OK ] Reached target Swap. [ OK ] Listening on Syslog Socket. [ OK ] Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Audit Socket. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. Mounting Huge Pages File System... Mounting POSIX Message Queue File System... Mounting Kernel Debug File System... Mounting Temporary Directory (/tmp)... Starting Create list of st?¦odes for the current kernel... Starting Journal Service... Mounting Kernel Configuration File System... Starting Remount Root and Kernel File Systems... [ 4.788921] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) Starting Apply Kernel Variables... Starting udev Coldplug all Devices... Starting Setup Virtual Console... [ OK ] Started Journal Service. [ OK ] Mounted Huge Pages File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Started Create list of sta??nodes for the current kernel. [ OK ] Mounted Kernel Configuration File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started Apply Kernel Variables. [ OK ] Started Setup Virtual Console. Starting Flush Journal to Persistent Storage... [ 5.049071] systemd-journald[260]: Received client request to flush runtime journal. Starting Create Static Device Nodes in /dev... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). Mounting /var/volatile... Starting udev Kernel Device Manager... [ OK ] Mounted /var/volatile. [ OK ] Started udev Coldplug all Devices. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... [ OK ] Started udev Kernel Device Manager. [ OK ] Started Load/Save Random Seed. [ OK ] Started Create Volatile Files and Directories. Starting Start Psplash Boot Screen... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Start Psplash Boot Screen. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanu[ 5.483883] Registered IR keymap rc-empty p of Temporary Directories. [ 5.499928] rc rc0: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0 [ OK ] Reached targe[ 5.509731] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0/input2 t System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on dropbear.socket. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Job spooling tools. [ 5.709437] imx-sdma 302b0000.dma-controller: loaded firmware 4.5 Starting Console Syste[ 5.728468] qca9377: loading out-of-tree module taints kernel. m Startup Logging... [ OK ] Started Periodic Command Scheduler. [ OK ] Started D-Bus System Message Bus. [ OK ] Started Configuration for i.MX GPU (Former rc_gpu.S). Starting Packet Filtering Framework... Starting Network Time Service (one-shot ntpdate mode)... Starting Telephony service... [ OK ] Started Updates psplash to basic. Starting RPC Bind Service... Starting System Logging Service... [ 5.924887] qca9377: loading driver v4.5.24.4 Starting Login Service... [ OK ] Started TEE Supplicant. [ OK ] Started Console System Startup Logging. [ OK ] Started Packet Filtering Framework. [ OK ] Started Network Time Service (one-shot ntpdate mode). [ OK ] Started RPC Bind Service. [ OK ] Started System Logging Service. [ 6.053304] mmc0: queuing unknown CIS tuple 0x01 (3 bytes) [ 6.076753] mmc0: queuing unknown CIS tuple 0x1a (5 bytes) [ 6.101769] mmc0: queuing unknown CIS tuple 0x1b (8 bytes) [ OK ] Started Telephony service. [ 6.138553] hifDeviceInserted: Dumping clocks (50000000,400000000) [ 6.145778] AR6000: Set async interrupt delay clock as 2. [ OK ] Created slice system-weston.slice. [ OK ] Reached target Network (Pre). Starting Save/Restore Sound Card State... Starting Connection service... [ 6.288276] AR6000: configuration opcode 3 is not used for Linux SDIO stack [ 6.298710] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 Starting Kernel Logging Service... Starting Network Service... [ OK ] Started Save/Restore Sound Card State. [ OK ] Started Login Service. [ OK ] Reached target Sound Card. [ OK ] Created slice system-systemd\x2dfsck.slice. [ OK ] Started Network Service. [ 6.436950] Atheros 8031 ethernet 30be0000.ethernet-1:00: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL) [ OK ] Found device /dev/mmcblk2p2. [ OK ] Started Connection service. [ OK ] Reached target Network. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started Update psplash to network. Starting Terminate Psplash Boot Screen... Starting /etc/rc.local Compatibility... Starting File System Check on /dev/mmcblk2p2... Starting Permit User Sessions... [ OK ] Started Kernel Logging Service. [FAILED] Failed to start Terminate Psplash Boot Screen. See 'systemctl status psplash-quit.service' for details. [ OK ] Started /etc/rc.local Compatibility. [ OK ] Started Permit User Sessions. [ OK ] Found device /dev/mmcblk2p1. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. Starting File System Check on /dev/mmcblk2p1 6.788855] HIF Interrupt processing is SYNC ONLY 0m... [ 6.794102] AR6000: configuration opcode 7 is only used for RTOS systems, not Linux systems [ 6.803106] AR6000: configuration opcode 5 is not used for Linux SDIO stack [ 6.811655] +HWT [ 6.818711] -HWT Starting Hostname Serv[ 6.821915] MAILBOX SWAP Service is enabled! ice... Starting Upda[ 6.829519] Reduced Tx Complete service is enabled! te UTMP about System Runlevel Cha[ 6.838608] HTCConnectService, host indicate support b2b bundle nges... Starting Weston Wayland Compositor (on tty7)... Starting WPA supplicant HTCConnectService, firmware decide to disabled b2b bundle [0m... [ OK ] Started 6.863315] HTC Service:0x0300 ep:1 TX flow control disabled ;1;39mFile System Check on /dev/m[ 6.864527] HTCConnectService, host indicate support b2b bundle mcblk2p2. [ 6.881263] HTCConnectService, firmware decide to disabled b2b bundle [ OK ] Started File System Check on /dev/mmcblk2p1. [ 6.903321] target uses HTT version 3.53; host uses 3.28 [ 6.913678] Host SW:4.5.24.4, FW:0.0.0.23, HW:QCA93x7_REV1_1 [ 6.919747] ol_pktlog_init: pktlogmod_init successfull [ 6.925198] ath_hif_sdio: HIF (Atheros/multi-bss) [ 6.925204] qca9377: driver loaded in 1000000 [ OK ] Started Weston Wayland Compositor (on tty7). [ OK ] Started WPA supplicant. [ OK ] Found device /dev/mmcblk1p1. [ OK ] Started Hostname Service. [ OK ] Started Update UTMP about System Runlevel Changes. [ OK ] Created slice User Slice of UID 0. Mounting /run/media/mmcblk2p1... Mounting /run/media/mmcblk2p2... Starting File S[ 7.150063] EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null) ystem Check on /dev/mmcblk1p1... Starting User Runtime Directory /run/user/0... [ OK ] Mounted /run/media/mmcblk2p1. [ OK ] Mounted /run/media/mmcblk2p2. [ OK ] Started User Runtime Directory /run/user/0. Starting User Manager for UID 0... [ 7.215014] audit: type=1006 audit(1605328853.336:2): pid=627 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1 [ OK ] Started File System Check on /dev/mmcblk1p1. Mounting /run/media/mmcblk1p1... [ OK ] Mounted /run/media/mmcblk1p1. [ OK ] Started User Manager for UID 0. [ OK ] Started Session c1 of user root. NXP i.MX Release Distro 5.4-zeus imx8mmevk ttymxc1 imx8mmevk login: