U-Boot 2018.03-dirty (Sep 10 2020 - 09:46:47 +0800) BOOTLOADER_VER=33.1 CPU: Freescale i.MX6SOLO rev1.3 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 28C Reset cause: POR Model: Freescale i.MX6 DualLite SABRE Smart Device Board Board: MX6-SabreSD DRAM: tws: ctls=83190000, misc=40081740 512 MiB start of tws_gpio_init IPT370P detected... no usb boot support usb boot is low power_init_board(), bypass MMC: mmc_set_clock() -- 1 , clock=400000, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=400000, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=400000, f_max=198000000, f_min=400000 FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... board_mmc_get_env_dev(), devno=1 mmc_start_init(), no_card=1 mmc_set_clock() -- 1 , clock=0, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=400000, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=50000000, f_max=198000000, f_min=400000 board_mmc_get_env_dev(), devno=1 *** Warning - bad CRC, using default environment board_mmc_get_env_dev(), devno=1 Failed (-5) No panel detected: default to Hannstar-XGA Display: Hannstar-XGA (1024x768) In: serial Out: serial Err: serial board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 flash target is MMC:0 mmc_start_init(), no_card=1 mmc_set_clock() -- 1 , clock=0, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=400000, f_max=198000000, f_min=400000 mmc_set_clock() -- 1 , clock=50000000, f_max=198000000, f_min=400000 Net: No ethernet found. board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 The SD card is locked. Can not write to a locked card. Fastboot: Normal Normal Boot Hit any key to stop autoboot: 0 => setenv bootargs console=ttymxc0,115200 init=/init video=mxcfb0:dev=ldb,fbpix=RGB32,bpp=32 video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off vmalloc=128M androidboot.console=ttymxc0 consoleblank=0 androidboot.hardware=freescale cma=320M galcore.contiguousSize=33554432 loop.max_part=7 buildvariant=userdebug androidboot.selinux=permissive maxcpus=1 => saveenv Saving Environment to MMC... board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 Writing to MMC(0)... The SD card is locked. Can not write to a locked card. board_mmc_get_env_dev(), devno=1 OK => boot board_mmc_get_env_dev(), devno=1 RNG already instantiated 0x40000003 Error: blob decap job failed 0x2000081a Error during blob decap operation: 0x2000081a In boota get fastboot lock status error. Set lock status board_mmc_get_env_dev(), devno=1 RNG already instantiated 0x40000003 The SD card is locked. Can not write to a locked card. board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 board_mmc_get_env_dev(), devno=1 RNG already instantiated 0x40000003 verify OK, boot 'boot' kernel @ 14008000 (9198320) ramdisk @ 15000000 (1835364) fdt @ 14f00000 (51438) ## Booting Android Image at 0x14007800 ... Kernel load addr 0x14008000 size 8983 KiB ## Flattened Device Tree blob at 14f00000 Booting using the fdt blob at 0x14f00000 XIP Kernel Image ... OK Using Device Tree in place at 14f00000, end 14f0f8ed tws: ldo_mode_set() @CONFIG_DM_PMIC_PFUZE100, ldo_bypass=1 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.98-dirty (tws@ubuntu) (gcc version 4.9.x 20150123 (prerelease) (GCC)) #11 SMP PREEMPT Thu Sep 3 12:00:37 +08 2020 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TWS IPT370P [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 320 MiB at 0x1c000000 [ 0.000000] tws: imx6q_map_io() [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] random: get_random_bytes called from start_kernel+0xac/0x450 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu @cba8c000 s40972 r8192 d24564 u73728 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttymxc0,115200 init=/init video=mxcfb0:dev=ldb,fbpix=RGB32,bpp=32 video=mxcfb1:off video=mxcfb2:off video=mxcfb3:off vmalloc=128M androidboot.console=ttymxc0 consoleblank=0 androidboot.hardware=freescale cma=320M galcore.contiguousSize=33554432 loop.max_part=7 buildvariant=userdebug androidboot.selinux=permissive maxcpus=1 androidboot.serialno=180251d4ea9c356c androidboot.btmacaddr=18:02:51:d4:ea:9c androidboot.soc_type=imx6dl androidboot.storage_type=sd gpt androidboot.boottime=1BLL:0,1BLE:16173,KL:0,KD:0,AVB:1127,ODT:0,SW:0 androidboot.bootreason=cold,powerkey androidboot.verifiedbootstate=green androidboot.slot_suffix= androidboot.vbmeta.device=PARTUUID=c482e0e9-6f18-410a-bd11-b02b92c0ce2f androidboot.vbmeta.avb_version=1.1 androidboot.vbmeta.device_state=locked androidboot.vbmeta.hash_alg=sha256 androidboot.vbmeta.size=2944 androidboot.vbmeta.digest=a7b96790bfc077ba89b7d8d8d63d5922c076e24c3b8404841a6f18b5edc9764e androidboot.veritymode=enforc [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 167740K/524288K available (13312K kernel code, 1057K rwdata, 4064K rodata, 1024K init, 505K bss, 28868K reserved, 327680K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0e00000 (14304 kB) [ 0.000000] .init : 0xc1300000 - 0xc1400000 (1024 kB) [ 0.000000] .data : 0xc1400000 - 0xc1508498 (1058 kB) [ 0.000000] .bss : 0xc150a000 - 0xc1588448 ( 506 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] ftrace: allocating 41786 entries in 123 pages [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] tws: mxc_set_cpu_type(), mxc_cpu_type=0x61(97) [ 0.000000] tws: imx6q_init_irq() [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76450001 [ 0.000000] tws: of_assigned_ldb_sels(), ldb_di0 parent clock PLL = 1 [ 0.000000] tws: of_assigned_ldb_sels(), ldb_di1 parent clock PLL = 0 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000025] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.002060] Console: colour dummy device 80x30 [ 0.002086] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.002105] pid_max: default: 32768 minimum: 301 [ 0.002231] Security Framework initialized [ 0.002246] SELinux: Initializing. [ 0.002349] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002367] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.003171] CPU: Testing write buffer coherency: ok [ 0.003214] CPU0: Spectre v2: using BPIALL workaround [ 0.003672] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039629] Setting up static identity map for 0x10100000 - 0x10100060 [ 0.059555] Hierarchical SRCU implementation. [ 0.099554] smp: Bringing up secondary CPUs ... [ 0.099570] smp: Brought up 1 node, 1 CPU [ 0.099581] SMP: Total of 1 processors activated (6.00 BogoMIPS). [ 0.099590] CPU: All CPU(s) started in SVC mode. [ 0.099637] CPU0: update max cpu_capacity 1024 [ 0.100503] devtmpfs: initialized [ 0.113913] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.114267] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.114292] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.127333] pinctrl core: initialized pinctrl subsystem [ 0.127783] tws: regulator_register(), name=regulator-dummy, set_machine_constraints ret=0 [ 0.127922] tws: regulator_register() --3, regulator_desc->name=regulator-dummy, regulator_desc->supply_name=(null) [ 0.128411] NET: Registered protocol family 16 [ 0.147724] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.148707] cpuidle: using governor menu [ 0.150512] CPU identified as i.MX6DL, silicon rev 1.3 [ 0.157525] vdd1p1: supplied by regulator-dummy [ 0.157642] tws: _regulator_get_voltage(), name=vdd1p1, ret=1100000 [ 0.157668] tws: _regulator_get_voltage(), name=vdd1p1, ret=1100000 [ 0.157680] tws: regulator_register(), name=vdd1p1, set_machine_constraints ret=0 [ 0.157852] tws: regulator_register() --3, regulator_desc->name=vdd1p1, regulator_desc->supply_name=(null) [ 0.158153] vdd3p0: supplied by regulator-dummy [ 0.158222] tws: _regulator_get_voltage(), name=vdd3p0, ret=3000000 [ 0.158238] tws: _regulator_get_voltage(), name=vdd3p0, ret=3000000 [ 0.158250] tws: regulator_register(), name=vdd3p0, set_machine_constraints ret=0 [ 0.158412] tws: regulator_register() --3, regulator_desc->name=vdd3p0, regulator_desc->supply_name=(null) [ 0.158715] vdd2p5: supplied by regulator-dummy [ 0.158781] tws: _regulator_get_voltage(), name=vdd2p5, ret=2500000 [ 0.158802] tws: _regulator_get_voltage(), name=vdd2p5, ret=2500000 [ 0.158814] tws: regulator_register(), name=vdd2p5, set_machine_constraints ret=0 [ 0.158989] tws: regulator_register() --3, regulator_desc->name=vdd2p5, regulator_desc->supply_name=(null) [ 0.159332] tws: _regulator_get_voltage(), name=vddarm, ret=1150000 [ 0.159357] tws: _regulator_get_voltage(), name=vddarm, ret=1150000 [ 0.159369] tws: regulator_register(), name=vddarm, set_machine_constraints ret=0 [ 0.159628] tws: regulator_register() --3, regulator_desc->name=vddarm, regulator_desc->supply_name=(null) [ 0.159947] tws: _regulator_get_voltage(), name=vddpu, ret=1250000 [ 0.159967] tws: _regulator_get_voltage(), name=vddpu, ret=1250000 [ 0.159979] tws: regulator_register(), name=vddpu, set_machine_constraints ret=0 [ 0.160201] tws: regulator_register() --3, regulator_desc->name=vddpu, regulator_desc->supply_name=(null) [ 0.160510] tws: _regulator_get_voltage(), name=vddsoc, ret=1175000 [ 0.160536] tws: _regulator_get_voltage(), name=vddsoc, ret=1175000 [ 0.160548] tws: regulator_register(), name=vddsoc, set_machine_constraints ret=0 [ 0.160777] tws: regulator_register() --3, regulator_desc->name=vddsoc, regulator_desc->supply_name=(null) [ 0.161410] tws: _regulator_get_voltage(), name=vdd3p0, ret=3000000 [ 0.161428] tws: _regulator_get_voltage(), name=vdd3p0, ret=3000000 [ 0.161444] tws: regulator_set_voltage(), ret=0 [ 0.161961] tws: _regulator_get_voltage(), name=vdd3p0, ret=3200000 [ 0.161978] tws: _regulator_get_voltage(), name=vdd3p0, ret=3200000 [ 0.161991] tws: regulator_set_voltage(), ret=0 [ 0.174411] BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1 [ 0.174436] caller is debug_smp_processor_id+0x20/0x24 [ 0.174451] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.98-dirty #11 [ 0.174461] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) [ 0.174494] [] (unwind_backtrace) from [] (show_stack+0x20/0x24) [ 0.174514] [] (show_stack) from [] (dump_stack+0x88/0x9c) [ 0.174534] [] (dump_stack) from [] (check_preemption_disabled+0x134/0x138) [ 0.174552] [] (check_preemption_disabled) from [] (debug_smp_processor_id+0x20/0x24) [ 0.174572] [] (debug_smp_processor_id) from [] (imx6q_init_machine+0x3c0/0x3e8) [ 0.174593] [] (imx6q_init_machine) from [] (customize_machine+0x30/0x38) [ 0.174616] [] (customize_machine) from [] (do_one_initcall+0x60/0x19c) [ 0.174635] [] (do_one_initcall) from [] (kernel_init_freeable+0x158/0x1fc) [ 0.174657] [] (kernel_init_freeable) from [] (kernel_init+0x18/0x160) [ 0.174677] [] (kernel_init) from [] (ret_from_fork+0x14/0x2c) [ 0.174689] tws: imx6q_init_machine(), cpu=0 [ 0.174768] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.174780] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.176246] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6qdl-sabresd/ov5640grp [ 0.176271] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6qdl-sabresd/ov5642grp [ 0.176289] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6qdl-sabresd/pciegrp [ 0.176305] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6qdl-sabresd/pciereggrp [ 0.176323] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/imx6qdl-sabresd/pwm1grp [ 0.176361] imx6dl-pinctrl 20e0000.iomuxc: Invalid fsl,pins or pins property in node /soc/aips-bus@02000000/iomuxc@020e0000/gpio_leds/gpioledsgrp [ 0.176430] imx6dl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.179213] imx rpmsg driver is registered. [ 0.179730] pstore: using zlib compression [ 0.180578] console [pstore-1] enabled [ 0.180854] pstore: Registered ramoops as persistent store backend [ 0.180874] ramoops: attached 0x100000@0x3ff00000, ecc: 0/0 [ 0.234157] tws: regulator_register(), name=usb_otg_vbus, set_machine_constraints ret=0 [ 0.234465] tws: regulator_register() --3, regulator_desc->name=usb_otg_vbus, regulator_desc->supply_name=vin [ 0.234660] tws: regulator_register(), name=usb_h1_vbus, set_machine_constraints ret=0 [ 0.234922] tws: regulator_register() --3, regulator_desc->name=usb_h1_vbus, regulator_desc->supply_name=vin [ 0.235084] tws: regulator_register(), name=wm8962-supply, set_machine_constraints ret=0 [ 0.235353] tws: regulator_register() --3, regulator_desc->name=wm8962-supply, regulator_desc->supply_name=(null) [ 0.235549] tws: regulator_register(), name=MPCIE_3V3, set_machine_constraints ret=0 [ 0.235823] tws: regulator_register() --3, regulator_desc->name=MPCIE_3V3, regulator_desc->supply_name=(null) [ 0.235982] tws: regulator_register(), name=sensor-supply, set_machine_constraints ret=0 [ 0.236271] tws: regulator_register() --3, regulator_desc->name=sensor-supply, regulator_desc->supply_name=(null) [ 0.236404] tws: regulator_register(), name=hdmi-5v-supply, set_machine_constraints ret=0 [ 0.236681] tws: regulator_register() --3, regulator_desc->name=hdmi-5v-supply, regulator_desc->supply_name=(null) [ 0.236840] tws: regulator_register(), name=mipi_dsi_pwr_on, set_machine_constraints ret=0 [ 0.237147] tws: regulator_register() --3, regulator_desc->name=mipi_dsi_pwr_on, regulator_desc->supply_name=(null) [ 0.237797] tws: This is TWS board, model(dt):TWS IPT370P [ 0.237816] tws: gpio_regulator_probe(), mxc_cpu_type=0x61(97) [ 0.237831] tws: cpu_is_mx6q=0, cpu_is_mx6dl=1, cpu_is_mx6ul()=0 [ 0.237842] tws: this is mx6solo CPU [ 0.237901] tws: gpio_regulator_probe(), ncores=1, ldo_bypass=1, anatop(before)=004c0012, (after)=007c001f [ 0.237923] GPIO IMX_GPIO_NR(3, 29) value: 1 [ 0.237941] GPIO IMX_GPIO_NR(1, 4) value: 0 [ 0.237960] GPIO IMX_GPIO_NR(1, 5) value: 1 [ 0.237991] tws: gpio_regulator_probe(), android [ 0.238009] GPIO IMX_GPIO_NR(6, 3) value: 0 [ 0.238028] GPIO IMX_GPIO_NR(6, 2) value: 0 [ 0.238046] GPIO IMX_GPIO_NR(2, 25) value: 1 [ 0.238062] tws: board id 768, (id1:0, id0:0) [ 0.238074] tws: bood mode 1 [ 0.238089] tws: This is IPT370P [ 0.238120] set AD_PWR off. [ 0.238136] tws: INIT USB Power (6, 4) and (6, 5) [ 0.238183] GPIO IMX_GPIO_NR(4, 26) value: 1 [ 0.238210] GPIO IMX_GPIO_NR(3, 17) value: 1 [ 0.238229] GPIO IMX_GPIO_NR(3, 18) value: 1 [ 0.238245] GPIO IMX_GPIO_NR(1, 19) value: 1 [ 0.238257] tws: Configure IPT370P BL PWM [ 0.238267] tws: IPT370P set USB POWER - CTP RST [ 0.239496] SCSI subsystem initialized [ 0.249915] usbcore: registered new interface driver usbfs [ 0.249983] usbcore: registered new interface driver hub [ 0.250089] usbcore: registered new device driver usb [ 0.250330] usb_phy_generic 2000000.aips-bus:usbphy_nop1: 2000000.aips-bus:usbphy_nop1 supply vcc not found, using dummy regulator [ 0.250548] usb_phy_generic 2000000.aips-bus:usbphy_nop2: 2000000.aips-bus:usbphy_nop2 supply vcc not found, using dummy regulator [ 0.252141] i2c i2c-0: IMX I2C adapter registered [ 0.252169] i2c i2c-0: can't use DMA, using PIO instead. [ 0.252872] i2c i2c-2: IMX I2C adapter registered [ 0.252899] i2c i2c-2: can't use DMA, using PIO instead. [ 0.253455] Linux video capture interface: v2.00 [ 0.253523] pps_core: LinuxPPS API ver. 1 registered [ 0.253538] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.253563] PTP clock support registered [ 0.279608] imx-ipuv3 2400000.ipu: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) [ 0.281234] mxc_vdoa 21e4000.vdoa: i.MX Video Data Order Adapter(VDOA) driver probed [ 0.282081] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 driver probed [ 0.282100] mxc_mipi_csi2 21dc000.mipi_csi: i.MX MIPI CSI2 dphy version is 0x3130302a [ 0.282229] MIPI CSI2 driver module loaded [ 0.282633] Advanced Linux Sound Architecture Driver Initialized. [ 0.283541] Bluetooth: Core ver 2.22 [ 0.283602] NET: Registered protocol family 31 [ 0.283616] Bluetooth: HCI device and connection manager initialized [ 0.283638] Bluetooth: HCI socket layer initialized [ 0.283656] Bluetooth: L2CAP socket layer initialized [ 0.283730] Bluetooth: SCO socket layer initialized [ 0.301360] clocksource: Switched to clocksource mxc_timer1 [ 0.391136] VFS: Disk quotas dquot_6.6.0 [ 0.391247] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.401840] tws: cpufreq_gov_performance_init(), [ 0.401863] tws: cpufreq_register_governor(), [ 0.402015] NET: Registered protocol family 2 [ 0.402712] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.402774] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.402847] TCP: Hash tables configured (established 4096 bind 4096) [ 0.402988] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.403022] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.403202] NET: Registered protocol family 1 [ 0.403537] Trying to unpack rootfs image as initramfs... [ 0.515213] Freeing initrd memory: 1796K [ 0.517284] hw perfevents: no interrupt-affinity property for /soc/pmu, guessing. [ 0.517530] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.520868] Bus freq driver module loaded [ 0.522017] audit: initializing netlink subsys (disabled) [ 0.523030] audit: type=2000 audit(0.520:1): state=initialized audit_enabled=0 res=1 [ 0.523144] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.529013] Registering sdcardfs 0.1 [ 0.529237] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.529773] fuse init (API version 7.26) [ 0.543463] io scheduler noop registered [ 0.543487] io scheduler deadline registered [ 0.543688] io scheduler cfq registered (default) [ 0.543708] io scheduler mq-deadline registered [ 0.543721] io scheduler kyber registered [ 0.546640] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 0.546757] tws: pwm_backlight_probe(), period(device tree)=2500000 [ 0.546878] tws: pwm:compute_duty_cycle(), brightness=7, duty_cycle=0 [ 0.547955] tws: pwm_backlight_update_status(), brightness=7, duty_cycle=1891304, period=2500000 [ 0.549193] tws: ldb_probe(), split-mode=0, dual-mode=0 [ 0.549225] tws: ldb_probe(), is_primary=1, primary_chno=0, chno=0, index=3 [ 0.549397] tws: of_get_display_timings(), num_timings=7, native_mode=0 [ 0.549411] tws: of_get_videomode(), num_timings=7, native_mode=0, index=3 [ 0.549529] tws: ldb_probe(), is_primary=0, primary_chno=0, chno=1, index=4 [ 0.549685] tws: of_get_display_timings(), num_timings=7, native_mode=0 [ 0.549699] tws: of_get_videomode(), num_timings=7, native_mode=0, index=4 [ 0.550952] tws: mxcfb_probe() [ 0.550993] tws: mxcfb_option_setup(), options=-877977041, *options=-877977041 [ 0.551013] tws: ldb_init(), chno=0 [ 0.551026] tws: ldb_init(), chan_0: is_used=1 [ 0.551039] tws: ldb_init(), chan_1: is_used=0 [ 0.551056] mxc_sdc_fb fb@0: registered mxc display driver ldb [ 0.551069] tws: mxcfb_probe()--1, dev_id=0 [ 0.568641] tws: ldb_setup(), chno=0, other_chno=1, id=0, mux_val=0x0 [ 0.568727] imx-ipuv3 2400000.ipu: WARNING: adapt panel end blank lines [ 0.591429] imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) [ 0.591482] mxc_sdc_fb fb@0: Updating SDC DISP3 BG buf 0 address=0x1C100000 [ 0.625292] tws: ldb_setup(), chno=0, other_chno=1, id=0, mux_val=0x0 [ 0.625363] imx-ipuv3 2400000.ipu: WARNING: adapt panel end blank lines [ 0.651525] mxc_sdc_fb fb@0: Updating SDC DISP3 BG buf 0 address=0x1C100000 [ 0.672355] Console: switching to colour frame buffer device 171x48 [ 0.685186] mxc_sdc_fb fb@0: Updating SDC DISP3 BG buf 1 address=0x1C100000 [ 0.704193] tws: mxcfb_probe() [ 0.704235] mxc_sdc_fb fb@1: Can't get fb option for mxcfb1! [ 0.706438] imx-sdma 20ec000.sdma: no iram assigned, using external mem [ 0.706972] imx-sdma 20ec000.sdma: Falling back to user helper [ 0.711033] mxs-dma 110000.dma-apbh: initialized [ 0.713425] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 0.714370] tws: pfuze100_regulator_probe()--1 [ 0.714881] pfuze100-regulator 2-0008: unrecognized pfuze chip ID! [ 0.714899] tws: No pfuze chip ID, force to pfuze100 [ 0.714915] pfuze100-regulator 2-0008: pfuze100 found. [ 0.715598] SW1AB: failed to get the current voltage(-6) [ 0.715616] tws: regulator_register(), name=SW1AB, set_machine_constraints ret=-6 [ 0.716320] tws: regulator_register() --3, regulator_desc->name=SW1AB, regulator_desc->supply_name=(null) [ 0.716698] SW1C: failed to get the current voltage(-6) [ 0.716716] tws: regulator_register(), name=SW1C, set_machine_constraints ret=-6 [ 0.717348] tws: regulator_register() --3, regulator_desc->name=SW1C, regulator_desc->supply_name=(null) [ 0.718043] SW2: failed to get the current voltage(-6) [ 0.718060] tws: regulator_register(), name=SW2, set_machine_constraints ret=-6 [ 0.718692] tws: regulator_register() --3, regulator_desc->name=SW2, regulator_desc->supply_name=(null) [ 0.719388] SW3A: failed to get the current voltage(-6) [ 0.719404] tws: regulator_register(), name=SW3A, set_machine_constraints ret=-6 [ 0.720045] tws: regulator_register() --3, regulator_desc->name=SW3A, regulator_desc->supply_name=(null) [ 0.720738] SW3B: failed to get the current voltage(-6) [ 0.720756] tws: regulator_register(), name=SW3B, set_machine_constraints ret=-6 [ 0.721490] tws: regulator_register() --3, regulator_desc->name=SW3B, regulator_desc->supply_name=(null) [ 0.722187] SW4: failed to get the current voltage(-6) [ 0.722203] tws: regulator_register(), name=SW4, set_machine_constraints ret=-6 [ 0.722836] tws: regulator_register() --3, regulator_desc->name=SW4, regulator_desc->supply_name=(null) [ 0.723200] SWBST: failed to get the current voltage(-6) [ 0.723216] tws: regulator_register(), name=SWBST, set_machine_constraints ret=-6 [ 0.723854] tws: regulator_register() --3, regulator_desc->name=SWBST, regulator_desc->supply_name=(null) [ 0.724219] VSNVS: failed to get the current voltage(-6) [ 0.724235] tws: regulator_register(), name=VSNVS, set_machine_constraints ret=-6 [ 0.724936] tws: regulator_register() --3, regulator_desc->name=VSNVS, regulator_desc->supply_name=(null) [ 0.725310] VREFDDR: failed to enable [ 0.725327] tws: regulator_register(), name=VREFDDR, set_machine_constraints ret=-6 [ 0.725627] tws: regulator_register() --3, regulator_desc->name=VREFDDR, regulator_desc->supply_name=(null) [ 0.725995] VGEN1: failed to get the current voltage(-6) [ 0.726011] tws: regulator_register(), name=VGEN1, set_machine_constraints ret=-6 [ 0.726669] tws: regulator_register() --3, regulator_desc->name=VGEN1, regulator_desc->supply_name=(null) [ 0.727046] VGEN2: failed to get the current voltage(-6) [ 0.727063] tws: regulator_register(), name=VGEN2, set_machine_constraints ret=-6 [ 0.727700] tws: regulator_register() --3, regulator_desc->name=VGEN2, regulator_desc->supply_name=(null) [ 0.728068] VGEN3: failed to get the current voltage(-6) [ 0.728084] tws: regulator_register(), name=VGEN3, set_machine_constraints ret=-6 [ 0.728706] tws: regulator_register() --3, regulator_desc->name=VGEN3, regulator_desc->supply_name=(null) [ 0.729075] VGEN4: failed to get the current voltage(-6) [ 0.729090] tws: regulator_register(), name=VGEN4, set_machine_constraints ret=-6 [ 0.729725] tws: regulator_register() --3, regulator_desc->name=VGEN4, regulator_desc->supply_name=(null) [ 0.730092] VGEN5: failed to get the current voltage(-6) [ 0.730108] tws: regulator_register(), name=VGEN5, set_machine_constraints ret=-6 [ 0.730740] tws: regulator_register() --3, regulator_desc->name=VGEN5, regulator_desc->supply_name=(null) [ 0.731105] VGEN6: failed to get the current voltage(-6) [ 0.731121] tws: regulator_register(), name=VGEN6, set_machine_constraints ret=-6 [ 0.731855] tws: regulator_register() --3, regulator_desc->name=VGEN6, regulator_desc->supply_name=(null) [ 0.731874] tws: pfuze100_regulator_probe()--2 [ 0.733010] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX [ 1.282190] tws: delayed work 1 [ 1.282196] tws: IPT370P, set USB POWER - LAN_RST, NEC_HUB_EN [ 2.858889] console [ttymxc0] enabled [ 2.863502] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 69, base_baud = 5000000) is a IMX [ 2.872855] 21ec000.serial: ttymxc2 at MMIO 0x21ec000 (irq = 70, base_baud = 5000000) is a IMX [ 2.882123] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 71, base_baud = 5000000) is a IMX [ 2.891395] 21f4000.serial: ttymxc4 at MMIO 0x21f4000 (irq = 72, base_baud = 5000000) is a IMX [ 2.902333] imx sema4 driver is registered. [ 2.907164] [drm] Initialized vivante 1.0.0 20120216 for platform:Vivante GCCore on minor 0 [ 2.915626] [drm] Initialized vivante 1.0.0 20120216 on minor 0 [ 2.932185] brd: module loaded [ 2.946094] loop: module loaded [ 2.949842] zram: Added device: zram0 [ 2.969411] libphy: Fixed MDIO Bus: probed [ 2.973984] tun: Universal TUN/TAP device driver, 1.6 [ 2.979293] CAN device driver interface [ 2.985397] PPP generic driver version 2.4.2 [ 2.989892] PPP BSD Compression module registered [ 2.994695] PPP Deflate Compression module registered [ 2.999786] PPP MPPE Compression module registered [ 3.004751] usbcore: registered new interface driver kaweth [ 3.010338] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.017820] usbcore: registered new interface driver pegasus [ 3.023558] usbcore: registered new interface driver rtl8150 [ 3.029275] usbcore: registered new interface driver r8152 [ 3.034847] usbcore: registered new interface driver asix [ 3.040305] usbcore: registered new interface driver ax88179_178a [ 3.046477] usbcore: registered new interface driver cdc_ether [ 3.052397] usbcore: registered new interface driver smsc95xx [ 3.058192] usbcore: registered new interface driver net1080 [ 3.063929] usbcore: registered new interface driver cdc_subset [ 3.069896] usbcore: registered new interface driver zaurus [ 3.075570] usbcore: registered new interface driver cdc_ncm [ 3.081242] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.087805] ehci-mxc: Freescale On-Chip EHCI Host driver [ 3.093341] usbcore: registered new interface driver usb-storage [ 3.099402] usbcore: registered new interface driver usb_ehset_test [ 3.107077] usbmisc_imx 2184800.usbmisc: 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator [ 3.118149] imx_usb 2184000.usb: 2184000.usb supply vbus not found, using dummy regulator [ 3.152374] imx_usb 2184200.usb: 2184200.usb supply vbus not found, using dummy regulator [ 3.163975] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.168897] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.201407] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.207062] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.213901] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.221135] usb usb1: Product: EHCI Host Controller [ 3.226046] usb usb1: Manufacturer: Linux 4.14.98-dirty ehci_hcd [ 3.232085] usb usb1: SerialNumber: ci_hdrc.1 [ 3.237144] hub 1-0:1.0: USB hub found [ 3.240971] hub 1-0:1.0: 1 port detected [ 3.257774] usbcore: registered new interface driver xpad [ 3.263387] usbcore: registered new interface driver usb_acecad [ 3.269367] usbcore: registered new interface driver aiptek [ 3.275034] usbcore: registered new interface driver gtco [ 3.280496] usbcore: registered new interface driver hanwang [ 3.286240] usbcore: registered new interface driver kbtab [ 3.294570] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-rtc-lp as rtc0 [ 3.304243] i2c /dev entries driver [ 3.308479] IR NEC protocol handler initialized [ 3.313074] IR RC5(x/sz) protocol handler initialized [ 3.318135] IR RC6 protocol handler initialized [ 3.322756] IR JVC protocol handler initialized [ 3.327297] IR Sony protocol handler initialized [ 3.331949] IR SANYO protocol handler initialized [ 3.336663] IR Sharp protocol handler initialized [ 3.341399] IR MCE Keyboard/mouse protocol handler initialized [ 3.347241] IR XMP protocol handler initialized [ 3.353372] mxc_v4l2_output v4l2_out: V4L2 device registered as video16 [ 3.364270] tws: regulator_set_voltage(), ret=-6 [ 3.370383] tws: regulator_set_voltage(), ret=-6 [ 3.375383] VGEN2: is_enabled() failed: -6 [ 3.379496] ov564x 0-003c: set core voltage failed [ 3.531728] ov5640_read_reg:write reg error:reg=300a [ 3.536713] camera ov5640 is not found [ 3.543015] tws: regulator_set_voltage(), ret=-6 [ 3.549086] tws: regulator_set_voltage(), ret=-6 [ 3.554120] VGEN2: is_enabled() failed: -6 [ 3.558230] ov5642_power_on:core set voltage error [ 3.611391] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.711719] ov5642_read_reg:write reg error:reg=300a [ 3.716696] camera ov5642 is not found [ 3.721035] usbcore: registered new interface driver uvcvideo [ 3.726874] USB Video Class driver (1.1.1) [ 3.732034] __power_supply_register: Expected proper parent device for 'battery' [ 3.739735] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 3.752189] __power_supply_register: Expected proper parent device for 'usb' [ 3.760899] mma8x5x 0-001c: read chip ID 0xfffffffa is not equal to 0x1a,0x2a,0x3a,0x4a,0x5a! [ 3.769874] mma8x5x: probe of 0-001c failed with error -22 [ 3.777038] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 3.783670] device-mapper: uevent: version 1.0.3 [ 3.788717] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com [ 3.807534] Bluetooth: HCI UART driver ver 2.3 [ 3.812104] Bluetooth: HCI UART protocol H4 registered [ 3.817370] Bluetooth: HCI UART protocol BCSP registered [ 3.822787] Bluetooth: HCI UART protocol ATH3K registered [ 3.828260] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 3.835366] bt power gpio is:2 [ 3.838577] mxc_bt_rfkill driver success loaded [ 3.843191] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.850775] usbcore: registered new interface driver btusb [ 3.856488] rfkill: BT RF going to : on [ 3.860554] hub 1-1:1.0: USB hub found [ 3.864443] usbcore: registered new interface driver ath3k [ 3.869972] tws: cpufreq_register_governor(), [ 3.874463] mxc_bt_rfkill_reset [ 3.877848] hub 1-1:1.0: 5 ports detected [ 3.883039] sdhci: Secure Digital Host Controller Interface driver [ 3.889274] sdhci: Copyright(c) Pierre Ossman [ 3.893927] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.961477] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 4.019423] mmc1: host does not support reading read-only switch, assuming write-enable [ 4.032391] mmc_set_clock() --1 , hz=50000000, f_max=198000000, f_min=48339 [ 4.042484] mmc1: new high speed SDHC card at address 0007 [ 4.049160] mmcblk1: mmc1:0007 SD08G 7.41 GiB [ 4.053777] mmc2: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 4.077729] Primary GPT is invalid, using alternate GPT. [ 4.083249] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 [ 4.141430] mmc3: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 4.162593] hidraw: raw HID events driver (C) Jiri Kosina [ 4.174170] usbcore: registered new interface driver usbhid [ 4.180983] usbhid: USB HID core driver [ 4.186537] ashmem: initialized [ 4.191615] usbcore: registered new interface driver snd-usb-audio [ 4.197816] tws_audio: snd_soc_init() [ 4.204123] tws_audio:, snd_soc_register_codec(),ret=0 [ 4.209286] tws_audio:, snd_soc_add_platform(),name=snd-soc-dummy, ret=0 [ 4.216096] usb 1-1.1: new high-speed USB device number 3 using ci_hdrc [ 4.237948] wm8962 0-001a: Failed to read ID register [ 4.246275] tws_audio:, snd_soc_register_component(),ret=0 [ 4.252178] tws_audio:, snd_soc_add_platform(),name=2034000.asrc, ret=0 [ 4.274018] NET: Registered protocol family 26 [ 4.278613] u32 classifier [ 4.282501] Actions configured [ 4.287067] Netfilter messages via NETLINK v0.30. [ 4.294116] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 4.300345] ctnetlink v0.93: registering with nfnetlink. [ 4.306425] xt_time: kernel timezone is -0000 [ 4.310963] IPv4 over IPsec tunneling driver [ 4.315942] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.324496] arp_tables: arp_tables: (C) 2002 David S. Miller [ 4.332443] Initializing XFRM netlink socket [ 4.340354] NET: Registered protocol family 10 [ 4.357740] Segment Routing with IPv6 [ 4.364718] mip6: Mobile IPv6 [ 4.367866] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 4.373532] random: fast init done [ 4.377436] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 4.384587] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 4.395881] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.402264] smsc95xx v1.0.6 [ 4.407367] NET: Registered protocol family 17 [ 4.413185] NET: Registered protocol family 15 [ 4.418919] can: controller area network core (rev 20170425 abi 9) [ 4.425468] NET: Registered protocol family 29 [ 4.430144] can: raw protocol (rev 20170425) [ 4.436713] can: broadcast manager protocol (rev 20170425 t) [ 4.445568] can: netlink gateway (rev 20170425) max_hops=1 [ 4.451821] Bluetooth: RFCOMM TTY layer initialized [ 4.457093] Bluetooth: RFCOMM socket layer initialized [ 4.462518] Bluetooth: RFCOMM ver 1.11 [ 4.466484] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 4.472050] Bluetooth: BNEP filters: protocol multicast [ 4.477438] Bluetooth: BNEP socket layer initialized [ 4.482589] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.488663] Bluetooth: HIDP socket layer initialized [ 4.494936] 8021q: 802.1Q VLAN Support v1.8 [ 4.500403] lib80211: common routines for IEEE802.11 drivers [ 4.508676] tws: imx6q_opp_check_speed_grading(), SPEED_GRADING[1:0]=2 [ 4.515356] tws: imx6q_opp_init() [ 4.518990] tws: imx6q_cpufreq_probe(), start probe [ 4.524323] tws: imx6q_cpufreq_probe(), Not support regulators(arm_reg, pu_reg, soc_reg) [ 4.532531] tws: imx6q_cpufreq_probe(), Not support regulators(dc_reg)) [ 4.539366] tws: imx6q_cpufreq_init(), arm_clk=3364765248, 792000 [ 4.545661] tws: imx6q_cpufreq_init(), [ 4.549622] tws: cpufreq_set_policy() 1--, new min and max freqs are 396000 - 996000 kHz [ 4.557893] tws: cpufreq_set_policy() 2--, new min and max freqs are 396000 - 996000 kHz [ 4.566091] tws: cpufreq_set_policy() IPT370P, change max freq to 792000 kHz [ 4.573242] tws: cpufreq_start_governor(), [ 4.577514] tws: cpufreq_register_driver(), [ 4.581896] cpu cpu0: Registered imx6q-cpufreq [ 4.586413] tws: imx6q_cpufreq_probe(), return 0 [ 4.591156] tws: imx6q_init_late() [ 4.597981] registered taskstats version 1 [ 4.623832] imx_epdc_fb 20f4000.epdc: can't get/select pinctrl [ 4.633037] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet, 00:de:fa:87:6e:d7 [ 4.661681] vddpu: supplied by SW1C [ 4.666175] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 4.674746] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). [ 4.687243] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C [ 4.710354] mxc_vpu 2040000.vpu_fsl: VPU initialized [ 4.716117] galcore: clk_get vg clock failed, disable vg! [ 4.722212] Galcore version 6.2.4.190076