U-Boot SPL 2021.04-dirty (Sep 25 2022 - 12:22:14 +0800) DDRINFO: start DRAM init DDRINFO: DRAM rate 4000MTS DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done SEC0: RNG instantiated Normal Boot WDT: Not found! Trying to boot from BOOTROM Find img info 0x&480265a0, size 856 Need continue download 1024 Download 1104800, Total size 1106432 NOTICE: BL31: v2.4(release):lf-5.10.72-2.2.0-0-g5782363f9 NOTICE: BL31: Built : 04:57:13, Sep 21 2022 U-Boot 2021.04-dirty (Sep 25 2022 - 12:22:14 +0800) CPU: i.MX8MP[8] rev1.1 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 38C Reset cause: POR Model: NXP i.MX8MPlus LPDDR4 EVK board DRAM: 6 GiB MMC: FSL_SDHC: 1, FSL_SDHC: 2 [*]-Video Link 0adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d fail to get display timings probe video device failed, ret -19 [0] lcd-controller@32e80000, video [1] mipi_dsi@32e60000, video_bridge [2] adv7535@3d, panel adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d fail to get display timings probe video device failed, ret -19 In: serial Out: serial Err: serial SEC0: RNG instantiated BuildInfo: - ATF 5782363 MMC: no card present Detect USB boot. Will enter fastboot mode! Net: eth0: ethernet@30be0000, eth1: ethernet@30bf0000 [PRIME] Fastboot: Normal Boot from USB for mfgtools *** Warning - Use default environment for mfgtools , using default environment Run bootcmd_mfg: run mfgtool_args;if iminfo ${initrd_addr}; then if test ${tee} = yes; then bootm ${tee_addr} ${initrd_addr} ${fdt_addr}; else booti ${loadaddr} ${initrd_addr} ${fdt_addr}; fi; else echo "Run fastboot ..."; fastboot 0; fi; Hit any key to stop autoboot: 0 ## Checking Image at 43800000 ... Legacy image found Image Name: fsl-image-mfgtool-initramfs-imx8 Created: 2021-04-02 19:12:14 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 14460776 Bytes = 13.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... Bad Data CRC Run fastboot ... init usb 1 Detect USB boot. Will enter fastboot mode! flash target is MMC:1 MMC: no card present MMC card init failed! MMC: no card present ** Block device MMC 1 not supported (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! flash target is MMC:2 (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Starting download of 1466880 bytes (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk ........... downloading of 1466880 bytes finished (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk writing to partition 'bootloader' Initializing 'bootloader' switch to partitions #1, OK mmc2(part 1) is current device Writing 'bootloader' MMC write: dev # 2, block # 0, count 2865 ... 2865 blocks written: OK Writing 'bootloader' DONE! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Starting download of 30118400 bytes (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk .......................................................................... .......................................................................... .......................................................................... ....... downloading of 30118400 bytes finished (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Starting download of 62933 bytes (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk downloading of 62933 bytes finished (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Detect USB boot. Will enter fastboot mode! (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Starting download of 14460840 bytes (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk .......................................................................... .................................... downloading of 14460840 bytes finished (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk (NULL udevice *): request 00000000fcf33600 was not queued to ep1in-bulk Moving Image from 0x40480000 to 0x40600000, end=42350000 ## Loading init Ramdisk from Legacy Image at 43800000 ... Image Name: fsl-image-mfgtool-initramfs-imx8 Created: 2021-04-02 19:12:14 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 14460776 Bytes = 13.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 0000000043000000, end 00000000430125d4 adv7535_mipi2hdmi adv7535@3d: Can't find cec device id=0x3c fail to probe panel device adv7535@3d fail to get display timings probe video device failed, ret -19 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.72-dirty (lambert@fae-server) (aarch64-poky-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.36.1.20210209) #23 SMP PREEMPT Sat Oct 8 14:17:19 CST 2022 [ 0.000000] Machine model: NXP i.MX8MPlus EVK board [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000c4000000, size 960 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000094300000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node vdev0buffer@94300000, compatible id shared-dma-pool [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000001bfffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x1bf440700-0x1bf442fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000923fffff] [ 0.000000] node 0: [mem 0x0000000092400000-0x00000000a43fffff] [ 0.000000] node 0: [mem 0x00000000a4400000-0x00000001bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000001bfffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 23 pages/cpu s56280 r8192 d29736 u94208 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1548288 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttymxc1,115200,115200 rdinit=/linuxrc clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000c0000000-0x00000000c4000000] (64MB) [ 0.000000] Memory: 4780380K/6291456K available (17920K kernel code, 1508K rwdata, 6928K rodata, 2944K init, 552K bss, 528036K reserved, 983040K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 160 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 [ 0.000000] ITS: No ITS available, not enabling LPIs [ 0.000000] random: get_random_bytes called from start_kernel+0x320/0x4e4 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns [ 0.000449] Console: colour dummy device 80x25 [ 0.000515] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) [ 0.000528] pid_max: default: 32768 minimum: 301 [ 0.000602] LSM: Security Framework initializing [ 0.000672] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000699] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.001879] rcu: Hierarchical SRCU implementation. [ 0.003173] EFI services will not be available. [ 0.003343] smp: Bringing up secondary CPUs ... [ 0.003705] Detected VIPT I-cache on CPU1 [ 0.003729] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 [ 0.003765] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.004212] Detected VIPT I-cache on CPU2 [ 0.004229] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 [ 0.004252] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.004641] Detected VIPT I-cache on CPU3 [ 0.004657] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 [ 0.004679] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.004739] smp: Brought up 1 node, 4 CPUs [ 0.004757] SMP: Total of 4 processors activated. [ 0.004766] CPU features: detected: 32-bit EL0 Support [ 0.004774] CPU features: detected: CRC32 instructions [ 0.004782] CPU features: detected: 32-bit EL1 Support [ 0.012840] CPU: All CPU(s) started at EL2 [ 0.012862] alternatives: patching kernel code [ 0.014665] devtmpfs: initialized [ 0.023237] KASLR disabled due to lack of seed [ 0.023381] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.023395] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.049709] pinctrl core: initialized pinctrl subsystem [ 0.050178] DMI not present or invalid. [ 0.050538] NET: Registered protocol family 16 [ 0.057725] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.058964] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.060376] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.060429] audit: initializing netlink subsys (disabled) [ 0.060599] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.061177] thermal_sys: Registered thermal governor 'step_wise' [ 0.061181] thermal_sys: Registered thermal governor 'power_allocator' [ 0.061541] cpuidle: using governor menu [ 0.061762] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.061828] ASID allocator initialised with 65536 entries [ 0.063102] Serial: AMBA PL011 UART driver [ 0.063163] imx mu driver is registered. [ 0.063181] imx rpmsg driver is registered. [ 0.105668] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver [ 0.124626] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.124641] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.124649] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.124658] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.125519] cryptd: max_cpu_qlen set to 1000 [ 0.128640] ACPI: Interpreter disabled. [ 0.129803] iommu: Default domain type: Translated [ 0.129943] vgaarb: loaded [ 0.130227] SCSI subsystem initialized [ 0.130574] usbcore: registered new interface driver usbfs [ 0.130613] usbcore: registered new interface driver hub [ 0.130638] usbcore: registered new device driver usb [ 0.132074] mc: Linux media interface: v0.10 [ 0.132099] videodev: Linux video capture interface: v2.00 [ 0.132166] pps_core: LinuxPPS API ver. 1 registered [ 0.132173] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.132190] PTP clock support registered [ 0.132372] EDAC MC: Ver: 3.0.0 [ 0.133675] FPGA manager framework [ 0.133755] Advanced Linux Sound Architecture Driver Initialized. [ 0.134391] Bluetooth: Core ver 2.22 [ 0.134421] NET: Registered protocol family 31 [ 0.134429] Bluetooth: HCI device and connection manager initialized [ 0.134440] Bluetooth: HCI socket layer initialized [ 0.134450] Bluetooth: L2CAP socket layer initialized [ 0.134465] Bluetooth: SCO socket layer initialized [ 0.135317] clocksource: Switched to clocksource arch_sys_counter [ 0.135477] VFS: Disk quotas dquot_6.6.0 [ 0.135525] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.135689] pnp: PnP ACPI: disabled [ 0.141852] NET: Registered protocol family 2 [ 0.142061] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.144779] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.144862] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.145271] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.146153] TCP: Hash tables configured (established 65536 bind 65536) [ 0.146272] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.146420] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.146679] NET: Registered protocol family 1 [ 0.147040] RPC: Registered named UNIX socket transport module. [ 0.147047] RPC: Registered udp transport module. [ 0.147052] RPC: Registered tcp transport module. [ 0.147058] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.147769] PCI: CLS 0 bytes, default 64 [ 0.147906] Unpacking initramfs... [ 0.872169] Freeing initrd memory: 14116K [ 0.872783] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.873619] kvm [1]: IPA Size Limit: 40 bits [ 0.875147] kvm [1]: GICv3: no GICV resource entry [ 0.875153] kvm [1]: disabling GICv2 emulation [ 0.875172] kvm [1]: GIC system register CPU interface enabled [ 0.875236] kvm [1]: vgic interrupt IRQ9 [ 0.875367] kvm [1]: Hyp mode initialized successfully [ 0.878232] Initialise system trusted keyrings [ 0.878335] workingset: timestamp_bits=42 max_order=21 bucket_order=0 [ 0.884253] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.884856] NFS: Registering the id_resolver key type [ 0.884878] Key type id_resolver registered [ 0.884885] Key type id_legacy registered [ 0.884967] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.884974] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.884994] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.885325] 9p: Installing v9fs 9p2000 file system support [ 0.921189] Key type asymmetric registered [ 0.921197] Asymmetric key parser 'x509' registered [ 0.921226] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 241) [ 0.921233] io scheduler mq-deadline registered [ 0.921238] io scheduler kyber registered [ 0.924117] samsung-hdmi-phy 32fdff00.hdmiphy: failed to get phy apb clk: -517 [ 0.924277] imx8-pcie-phy 32f00000.pcie-phy: failed to get imx pcie phy clock [ 0.928979] pwm-backlight lvds_backlight: supply power not found, using dummy regulator [ 0.929693] EINJ: ACPI disabled. [ 0.941128] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [ 0.941142] imx-sdma 30bd0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [ 0.943284] mxs-dma 33000000.dma-apbh: initialized [ 0.945874] Bus freq driver module loaded [ 0.952096] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.954571] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 35, base_baud = 5000000) is a IMX [ 0.955301] 30880000.serial: ttymxc2 at MMIO 0x30880000 (irq = 36, base_baud = 5000000) is a IMX [ 0.955882] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 37, base_baud = 1500000) is a IMX [ 2.023057] printk: console [ttymxc1] enabled [ 2.030394] imx-lcdifv3 32e80000.lcd-controller: No pix clock get: -517 [ 2.037751] imx-lcdifv3 32e90000.lcd-controller: No pix clock get: -517 [ 2.044681] imx-lcdifv3 32fc6000.lcd-controller: No irq get, ret=-517 [ 2.056139] imx-hdmi-pavi 32fc4000.hdmi-pai-pvi: No pvi clock get [ 2.073770] loop: module loaded [ 2.078135] megasas: 07.714.04.00-rc1 [ 2.083533] imx ahci driver is registered. [ 2.092370] spi-nor spi0.0: n25q256ax1 (32768 Kbytes) [ 2.101729] libphy: Fixed MDIO Bus: probed [ 2.107282] tun: Universal TUN/TAP device driver, 1.6 [ 2.113252] thunder_xcv, ver 1.0 [ 2.116525] thunder_bgx, ver 1.0 [ 2.119787] nicpf, ver 1.0 [ 2.123475] pps pps0: new PPS source ptp0 [ 2.135137] hclge is initializing [ 2.138504] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.145739] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.151097] e1000: Intel(R) PRO/1000 Network Driver [ 2.156001] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 2.161821] e1000e: Intel(R) PRO/1000 Network Driver [ 2.166803] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.172772] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.178177] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.183784] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 2.190057] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.196200] sky2: driver version 1.30 [ 2.200741] imx-dwmac 30bf0000.ethernet: IRQ eth_lpi not found [ 2.206788] usbcore: registered new interface driver r8152 [ 2.212321] usbcore: registered new interface driver asix [ 2.217764] usbcore: registered new interface driver ax88179_178a [ 2.223890] usbcore: registered new interface driver cdc_ether [ 2.229759] usbcore: registered new interface driver net1080 [ 2.235453] usbcore: registered new interface driver cdc_subset [ 2.241407] usbcore: registered new interface driver zaurus [ 2.247031] usbcore: registered new interface driver cdc_ncm [ 2.252945] VFIO - User Level meta-driver version: 0.3 [ 2.259859] imx8mp-dwc3 32f10100.usb: failed to get dwc3 platform device [ 2.270162] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.276709] ehci-pci: EHCI PCI platform driver [ 2.281193] ehci-platform: EHCI generic platform driver [ 2.286697] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.292908] ohci-pci: OHCI PCI platform driver [ 2.297387] ohci-platform: OHCI generic platform driver [ 2.303655] usbcore: registered new interface driver uas [ 2.309017] usbcore: registered new interface driver usb-storage [ 2.315094] usbcore: registered new interface driver usbserial_generic [ 2.321650] usbserial: USB Serial support registered for generic [ 2.327689] usbcore: registered new interface driver ftdi_sio [ 2.333454] usbserial: USB Serial support registered for FTDI USB Serial Device [ 2.340789] usbcore: registered new interface driver usb_serial_simple [ 2.347337] usbserial: USB Serial support registered for carelink [ 2.353448] usbserial: USB Serial support registered for zio [ 2.359127] usbserial: USB Serial support registered for funsoft [ 2.365151] usbserial: USB Serial support registered for flashloader [ 2.371521] usbserial: USB Serial support registered for google [ 2.377467] usbserial: USB Serial support registered for libtransistor [ 2.384015] usbserial: USB Serial support registered for vivopay [ 2.390038] usbserial: USB Serial support registered for moto_modem [ 2.396325] usbserial: USB Serial support registered for motorola_tetra [ 2.402962] usbserial: USB Serial support registered for novatel_gps [ 2.409340] usbserial: USB Serial support registered for hp4x [ 2.415103] usbserial: USB Serial support registered for suunto [ 2.421046] usbserial: USB Serial support registered for siemens_mpi [ 2.427440] usbcore: registered new interface driver usb_ehset_test [ 2.437029] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 [ 2.452092] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 [ 2.458312] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:35:17 UTC (2117) [ 2.467854] i2c /dev entries driver [ 2.476022] Bluetooth: HCI UART driver ver 2.3 [ 2.480486] Bluetooth: HCI UART protocol H4 registered [ 2.485633] Bluetooth: HCI UART protocol BCSP registered [ 2.490967] Bluetooth: HCI UART protocol LL registered [ 2.496116] Bluetooth: HCI UART protocol ATH3K registered [ 2.501543] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 2.507912] Bluetooth: HCI UART protocol Broadcom registered [ 2.513594] Bluetooth: HCI UART protocol QCA registered [ 2.519096] EDAC MC: ECC not enabled [ 2.524080] sdhci: Secure Digital Host Controller Interface driver [ 2.530274] sdhci: Copyright(c) Pierre Ossman [ 2.535097] Synopsys Designware Multimedia Card Interface Driver [ 2.541911] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.548738] sdhci-esdhc-imx 30b50000.mmc: voltage-ranges unspecified [ 2.549077] sdhci-esdhc-imx 30b60000.mmc: voltage-ranges unspecified [ 2.561774] ledtrig-cpu: registered to indicate activity on CPUs [ 2.568752] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 2.575691] usbcore: registered new interface driver usbhid [ 2.581270] usbhid: USB HID core driver [ 2.585600] mxc-mipi-csi2-sam 32e40000.csi: supply mipi-phy not found, using dummy regulator [ 2.593827] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA [ 2.599251] imx-dsp-rproc 3b6e8000.dsp: Failed to get clock dsp_clk1 [ 2.607545] imx-dsp-rproc 3b6e8000.dsp: failed on imx_dsp_rproc_clk_get [ 2.614514] remoteproc remoteproc0: releasing imx-dsp-rproc [ 2.627548] Galcore version 6.4.3.p2.336687 [ 2.704885] mmc2: new HS400 Enhanced strobe MMC card at address 0001 [ 2.712610] mmcblk2: mmc2:0001 DG4032 29.1 GiB [ 2.717361] mmcblk2boot0: mmc2:0001 DG4032 partition 1 4.00 MiB [ 2.723486] mmcblk2boot1: mmc2:0001 DG4032 partition 2 4.00 MiB [ 2.730178] mmcblk2rpmb: mmc2:0001 DG4032 partition 3 4.00 MiB, chardev (511:0) [ 2.739550] mmcblk2: p1 p2 [ 2.755745] [drm] Initialized vivante 1.0.0 20170808 for 40000000.mix_gpu_ml on minor 0 [ 2.765206] hantrodec 0 : module inserted. Major = 510 [ 2.771020] hantrodec 1 : module inserted. Major = 510 [ 2.777753] hantroenc: HW at base <0000000038320000> with ID <0x80006200> [ 2.784678] hx280enc: module inserted. Major <509> [ 2.798054] fsl-sai 30c20000.sai: failed to get bus clock: -517 [ 2.806062] fsl-sai 30c30000.sai: failed to get bus clock: -517 [ 2.815414] fsl-micfil-dai 30ca0000.micfil: failed to get core clock: -517 [ 2.823111] fsl-easrc 30c90000.easrc: failed to get mem clock [ 2.829376] fsl,imx8mp-audio-xcvr 30cc0000.xcvr: failed to get ipg clock [ 2.836777] fsl-aud2htx 30cb0000.aud2htx: failed to get mem clock [ 2.844150] imx-xcvr sound-xcvr: snd_soc_register_card failed: -517 [ 2.851566] imx-micfil sound-micfil: snd_soc_register_card failed (-517) [ 2.858966] imx-cdnhdmi sound-hdmi: snd_soc_register_card failed (-517) [ 2.865704] NET: Registered protocol family 26 [ 2.870605] NET: Registered protocol family 10 [ 2.876297] Segment Routing with IPv6 [ 2.880035] NET: Registered protocol family 17 [ 2.885496] Bluetooth: RFCOMM TTY layer initialized [ 2.890399] Bluetooth: RFCOMM socket layer initialized [ 2.895583] Bluetooth: RFCOMM ver 1.11 [ 2.899354] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 2.904676] Bluetooth: BNEP filters: protocol multicast [ 2.909912] Bluetooth: BNEP socket layer initialized [ 2.914883] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 2.920812] Bluetooth: HIDP socket layer initialized [ 2.925809] 8021q: 802.1Q VLAN Support v1.8 [ 2.930018] lib80211: common routines for IEEE802.11 drivers [ 2.935783] 9pnet: Installing 9P2000 support [ 2.940085] tsn generic netlink module v1 init... [ 2.944865] Key type dns_resolver registered [ 2.949688] registered taskstats version 1 [ 2.953803] Loading compiled-in X.509 certificates [ 2.993346] nxp-pca9450 0-0025: pca9450bc probed. [ 2.998227] i2c i2c-0: IMX I2C adapter registered [ 3.004231] adv7511 1-003d: supply avdd not found, using dummy regulator [ 3.011088] adv7511 1-003d: supply dvdd not found, using dummy regulator [ 3.017837] adv7511 1-003d: supply pvdd not found, using dummy regulator [ 3.024587] adv7511 1-003d: supply a2vdd not found, using dummy regulator [ 3.031423] adv7511 1-003d: supply v3p3 not found, using dummy regulator [ 3.038170] adv7511 1-003d: supply v1p2 not found, using dummy regulator [ 3.046030] adv7511 1-003d: Probe failed. Remote port 'mipi_dsi@32e60000' disabled [ 3.108037] it6263 1-004c: Probe failed. Remote port 'lvds-channel@0' disabled [ 3.116028] ov5640 1-003c: supply DOVDD not found, using dummy regulator [ 3.122852] ov5640 1-003c: supply AVDD not found, using dummy regulator [ 3.129524] ov5640 1-003c: supply DVDD not found, using dummy regulator [ 3.181846] ov5640 1-003c: ov5640_read_reg: error: reg=300a [ 3.187437] ov5640 1-003c: ov5640_check_chip_id: failed to read chip identifier [ 3.197832] i2c i2c-1: IMX I2C adapter registered [ 3.203808] pca953x 2-0020: using no AI [ 3.209578] i2c i2c-2: IMX I2C adapter registered [ 3.216103] imx8mq-usb-phy 381f0040.usb-phy: supply vbus not found, using dummy regulator [ 3.224737] imx8mq-usb-phy 382f0040.usb-phy: supply vbus not found, using dummy regulator [ 3.233210] samsung-hdmi-phy 32fdff00.hdmiphy: failed to get phy apb clk: -517 [ 3.243365] pwm-backlight lvds_backlight: supply power not found, using dummy regulator [ 3.244036] imx6q-pcie 33800000.pcie: supply epdev_on not found, using dummy regulator [ 3.259647] imx6q-pcie 33800000.pcie: EXT REF_CLK is used!. [ 3.265833] imx6q-pcie 33800000.pcie: PCIe PHY PLL clock is locked. [ 3.275623] SoC: i.MX8MP revision 1.1 [ 3.279618] imx-cpufreq-dt imx-cpufreq-dt: cpu speed grade 5 mkt segment 0 supported-hw 0x20 0x1 [ 3.292087] imx-lcdifv3 32fc6000.lcd-controller: No irq get, ret=-517 [ 3.303108] pps pps0: new PPS source ptp0 [ 3.313874] libphy: fec_enet_mii_bus: probed [ 3.322790] fec 30be0000.ethernet eth0: registered PHC device 0 [ 3.329688] imx-dwmac 30bf0000.ethernet: IRQ eth_lpi not found [ 3.331380] imx6q-pcie 33800000.pcie: PCIe PLL locked after 0 us. [ 3.335734] imx-dwmac 30bf0000.ethernet: no reset control found [ 3.341683] imx6q-pcie 33800000.pcie: host bridge /soc@0/pcie@33800000 ranges: [ 3.348406] imx-dwmac 30bf0000.ethernet: User ID: 0x10, Synopsys ID: 0x51 [ 3.354826] imx6q-pcie 33800000.pcie: No bus range found for /soc@0/pcie@33800000, using [bus 00-ff] [ 3.361629] imx-dwmac 30bf0000.ethernet: DWMAC4/5 [ 3.370945] imx6q-pcie 33800000.pcie: IO 0x001ff80000..0x001ff8ffff -> 0x0000000000 [ 3.375711] imx-dwmac 30bf0000.ethernet: DMA HW capability register supported [ 3.383903] imx6q-pcie 33800000.pcie: MEM 0x0018000000..0x001fefffff -> 0x0018000000 [ 3.391020] imx-dwmac 30bf0000.ethernet: RX Checksum Offload Engine supported [ 3.391027] imx-dwmac 30bf0000.ethernet: TX Checksum insertion supported [ 3.399273] imx6q-pcie 33800000.pcie: invalid resource [ 3.406336] imx-dwmac 30bf0000.ethernet: Wake-Up On Lan supported [ 3.406393] imx-dwmac 30bf0000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 3.431942] imx-dwmac 30bf0000.ethernet: Enabled Flow TC (entries=8) [ 3.438312] imx-dwmac 30bf0000.ethernet: Enabling HW TC (entries=256, max_off=256) [ 3.445897] imx-dwmac 30bf0000.ethernet: Using 34 bits DMA width [ 3.452275] libphy: stmmac: probed [ 3.463387] mxc-mipi-csi2-sam 32e40000.csi: supply mipi-phy not found, using dummy regulator [ 3.463956] sdhci-esdhc-imx 30b50000.mmc: voltage-ranges unspecified [ 3.472153] mxc-mipi-csi2-sam 32e40000.csi: lanes: 2, hs_settle: 13, clk_settle: 2, wclk: 1, freq: 500000000 [ 3.478262] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO [ 3.489534] isi-capture 32e00000.isi:cap_device: deferring 32e00000.isi:cap_device device registration [ 3.503255] mxc-isi 32e00000.isi: mxc_isi.0 registered successfully [ 3.510818] remoteproc remoteproc0: imx-dsp-rproc is available [ 3.510830] imx6q-pcie 33800000.pcie: Link up [ 3.521052] imx6q-pcie 33800000.pcie: Link up [ 3.524047] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA [ 3.525438] imx6q-pcie 33800000.pcie: Link up, Gen1 [ 3.534049] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 62 [ 3.542639] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 63 [ 3.547887] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 64 [ 3.553131] fsl-micfil-dai 30ca0000.micfil: GET IRQ: 65 [ 3.571219] imx-cdnhdmi sound-hdmi: snd_soc_register_card failed (-517) [ 3.589387] random: fast init done [ 3.608263] imx-drm display-subsystem: bound imx-lcdifv3-crtc.0 (ops lcdifv3_crtc_ops) [ 3.616273] imx-drm display-subsystem: bound imx-lcdifv3-crtc.1 (ops lcdifv3_crtc_ops) [ 3.624267] imx-drm display-subsystem: bound imx-lcdifv3-crtc.2 (ops lcdifv3_crtc_ops) [ 3.632274] imx_sec_dsim_drv 32e60000.mipi_dsi: version number is 0x1060200 [ 3.639284] imx_sec_dsim_drv 32e60000.mipi_dsi: Failed to attach bridge: 32e60000.mipi_dsi [ 3.647564] imx_sec_dsim_drv 32e60000.mipi_dsi: failed to bind sec dsim bridge: -19 [ 3.651423] imx6q-pcie 33800000.pcie: PCI host bridge to bus 0000:00 [ 3.655243] imx-drm display-subsystem: bound 32e60000.mipi_dsi (ops imx_sec_dsim_ops) [ 3.661655] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.669447] imx-drm display-subsystem: bound 32c00000.bus:ldb@32ec005c (ops imx8mp_ldb_ops) [ 3.674898] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 3.683580] dwhdmi-imx 32fd8000.hdmi: Detected HDMI TX controller v2.13a with HDCP (samsung_dw_hdmi_phy2) [ 3.689430] pci_bus 0000:00: root bus resource [mem 0x18000000-0x1fefffff] [ 3.689455] pci 0000:00:00.0: [16c3:abcd] type 01 class 0x060400 [ 3.700390] dwhdmi-imx 32fd8000.hdmi: registered DesignWare HDMI I2C bus driver [ 3.705883] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 3.714411] imx-drm display-subsystem: bound 32fd8000.hdmi (ops dw_hdmi_imx_ops) [ 3.719212] pci 0000:00:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref] [ 3.725959] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 1 [ 3.732930] pci 0000:00:00.0: supports D1 [ 3.739628] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes [ 3.747428] pci 0000:00:00.0: PME# supported from D0 D1 D3hot D3cold [ 3.755812] debugfs: File 'Playback' in directory 'dapm' already present! [ 3.760596] pci 0000:01:00.0: MSI quirk detected; MSI disabled [ 3.764721] debugfs: File 'Capture' in directory 'dapm' already present! [ 3.771475] pci 0000:01:00.0: quirk_disable_all_msi+0x0/0x40 took 10619 usecs [ 3.771480] pci 0000:01:00.0: [1b4b:2b42] type 00 class 0x020000 [ 3.777403] imx-drm display-subsystem: [drm] Cannot find any crtc or sizes [ 3.784106] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 3.793787] debugfs: Directory '30c90000.easrc' with parent 'wm8960-audio' already present! [ 3.797215] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit pref] [ 3.827342] pci 0000:01:00.0: supports D1 D2 [ 3.831619] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold [ 3.838164] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 3.866718] pci 0000:00:00.0: BAR 0: assigned [mem 0x18000000-0x180fffff] [ 3.873531] pci 0000:00:00.0: BAR 15: assigned [mem 0x18100000-0x182fffff pref] [ 3.880888] pci 0000:00:00.0: BAR 6: assigned [mem 0x18300000-0x1830ffff pref] [ 3.888144] pci 0000:01:00.0: BAR 0: assigned [mem 0x18100000-0x181fffff 64bit pref] [ 3.895949] pci 0000:01:00.0: BAR 2: assigned [mem 0x18200000-0x182fffff 64bit pref] [ 3.903753] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.909110] pci 0000:00:00.0: bridge window [mem 0x18100000-0x182fffff pref] [ 3.916596] pcieport 0000:00:00.0: PME: Signaling with IRQ 249 [ 3.927438] input: audio-hdmi HDMI Jack as /devices/platform/sound-hdmi/sound/card4/input2 [ 3.939610] isi-m2m 32e00000.isi:m2m_device: Register m2m success for ISI.0 [ 3.946673] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.959584] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.966193] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.967641] clk: Not disabling unused clocks [ 3.974816] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ 3.979146] ALSA device list: [ 3.989834] #0: imx-audio-xcvr [ 3.993079] #1: imx-audio-micfil [ 3.996485] #2: bt-sco-audio [ 3.999546] #3: wm8960-audio [ 4.002599] #4: audio-hdmi [ 4.006232] Freeing unused kernel memory: 2944K [ 4.035658] Run /linuxrc as init process Found New UDC: 38200000.dwc3 38200000.dwc3 0 ffs.utp0 [ 4.075981] file system registered [ 4.088963] Mass Storage Function, version: 2009/09/11 [ 4.094154] LUN: removable file: (no medium) run utp at /dev/usb-utp0/ep0 . [ 4.102229] read descriptors [ 4.106987] read strings uuu fastboot client 1.0.0 [built Apr 2 2021 14:10:56] Start init usb write string Start handle command uuc /dev/utp uuc 0.6 [built Apr 2 2021 14:10:56] UTP: Waiting for /dev/utp to appear run shell cmd: while [ ! -e /dev/mmcblk*boot0 ]; do sleep 1; echo "wait for /dev/mmcblk*boot* appear"; done; run shell cmd: dev=`ls /dev/mmcblk*boot*`; dev=($dev); dev=${dev[0]}; dev=${dev#/dev/mmcblk}; dev=${dev%boot*}; echo $dev > /tmp/mmcdev; run shell cmd: mmc=`cat /tmp/mmcdev`; dd if=/dev/zero of=/dev/mmcblk${mmc} bs=512 count=1 1+0 records in 1+0 records out 512 bytes copied, 0.00171287 s, 299 kB/s run shell cmd: mmc=`cat /tmp/mmcdev`; PARTSTR=$'10M,500M,0c\n600M,,83\n'; echo "$PARTSTR" | sfdisk --force /dev/mmcblk${mmc} Partition #1 contains a vfat signature. Partition #2 contains a ext3 signature. [ 8.914461] mmcblk2: p1 p2 run shell cmd: mmc=`cat /tmp/mmcdev`; dd if=/dev/zero of=/dev/mmcblk${mmc} bs=1k seek=4096 count=1 1+0 records in 1+0 records out 1024 bytes (1.0 kB, 1.0 KiB) copied, 0.000566375 s, 1.8 MB/s run shell cmd: sync run shell cmd: mmc=`cat /tmp/mmcdev`; while [ ! -e /dev/mmcblk${mmc}p1 ]; do sleep 1; done run shell cmd: mmc=`cat /tmp/mmcdev`; mkfs.vfat /dev/mmcblk${mmc}p1 run shell cmd: mmc=`cat /tmp/mmcdev`; mkdir -p /mnt/fat run shell cmd: mmc=`cat /tmp/mmcdev`; mount -t vfat /dev/mmcblk${mmc}p1 /mnt/fat WOpen:/mnt/fat WOpen:/mnt/fat/Image-imx8mpevk.bin WOpen:/mnt/fat WOpen:/mnt/fat/imx8mp-evk.dtb run shell cmd: umount /mnt/fat run shell cmd: mmc=`cat /tmp/mmcdev`; mkfs.ext3 -F -E nodiscard /dev/mmcblk${mmc}p2 mke2fs 1.45.3 (14-Jul-2019) [ 13.271356] random: crng init done run shell cmd: mkdir -p /mnt/ext3 run shell cmd: mmc=`cat /tmp/mmcdev`; mount /dev/mmcblk${mmc}p2 /mnt/ext3 [ 22.416609] EXT4-fs (mmcblk2p2): mounting ext3 file system using the ext4 subsystem [ 22.440894] EXT4-fs (mmcblk2p2): mounted filesystem with ordered data mode. Opts: (null) run shell cmd: export EXTRACT_UNSAFE_SYMLINKS=1; tar -jx -C /mnt/ext3 WOpen:- [ 35.811372] can1-stby: disabling [ 35.814614] can2-stby: disabling [ 35.817893] VSD_3V3: disabling [ 62.431732] imx-sdma 30bd0000.dma-controller: external firmware not found, using ROM firmware [ 62.431830] imx-sdma 30e10000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 [ 62.450783] imx-sdma 30e10000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin [ 64.479419] cfg80211: failed to load regulatory.db [ 123.871732] imx-sdma 30e10000.dma-controller: external firmware not found, using ROM firmware wait for async proccess finish run shell cmd: umount /mnt/ext3