[2021-05-31 15:44:07] U-Boot SPL 2016.012.0+ga9b437f (May 31 2021 - 10:55:45) [2021-05-31 15:44:07] Trying to boot from MMC [2021-05-31 15:44:07] [2021-05-31 15:44:07] [2021-05-31 15:44:07] U-Boot 2016.012.0+ga9b437f (May 31 2021 - 10:55:45 +0530) [2021-05-31 15:44:07] [2021-05-31 15:44:07] CPU: Freescale LayerScape LS1021, Version: 2.0, (0x87001120) [2021-05-31 15:44:07] Clock Configuration: [2021-05-31 15:44:07] CPU0(ARMV7):640 MHz, [2021-05-31 15:44:07] Bus:192 MHz, DDR:512 MHz (1024 MT/s data rate), [2021-05-31 15:44:07] Reset Configuration Word (RCW): [2021-05-31 15:44:07] 00000000: 0608000a 00000000 00000000 00000000 [2021-05-31 15:44:07] 00000010: 10000000 00007900 60040a00 21046000 [2021-05-31 15:44:07] 00000020: 00000000 00000000 00000000 0021c900 [2021-05-31 15:44:07] 00000030: 80000100 04093340 00000000 00000000 [2021-05-31 15:44:07] I2C: ready [2021-05-31 15:44:07] Board: PEEK-ATC-GEN2 [2021-05-31 15:44:07] DRAM: 512 MiB [2021-05-31 15:44:07] Flash: 0 Bytes [2021-05-31 15:44:07] MMC: FSL_SDHC: 0 [2021-05-31 15:44:08] *** Warning - bad CRC, using default environment [2021-05-31 15:44:08] [2021-05-31 15:44:08] In: serial [2021-05-31 15:44:08] Out: serial [2021-05-31 15:44:08] Err: serial [2021-05-31 15:44:08] Net: eTSEC1, eTSEC3 [PRIME] [2021-05-31 15:44:08] Hit any key to stop autoboot: 0 [2021-05-31 15:44:08] => [2021-05-31 15:44:08] => [2021-05-31 15:44:08] => mdio list [2021-05-31 15:44:15] FSL_MDIO: [2021-05-31 15:44:15] 1 - Generic PHY <--> eTSEC1 [2021-05-31 15:44:15] 2 - Generic PHY <--> eTSEC3 [2021-05-31 15:44:15] => mii info [2021-05-31 15:44:45] PHY 0x01: OUI = 0x80028, Model = 0x24, Rev = 0x00, 100baseT, FDX [2021-05-31 15:44:45] PHY 0x02: OUI = 0x80028, Model = 0x24, Rev = 0x00, 10baseT, HDX [2021-05-31 15:44:45] PHY 0x1F: OUI = 0x0000, Model = 0x00, Rev = 0x00, 1000baseX, HDX [2021-05-31 15:44:45] => setenv eth1addr 00:04:9f:05:80:bd [2021-05-31 15:45:33] => setenv eth2addr 00:04:9f:05:80:be [2021-05-31 15:45:33] => setenv ethaddr 00:04:9f:05:80:bc [2021-05-31 15:45:40] => boot [2021-05-31 15:45:42] reading uImage [2021-05-31 15:45:42] 3338456 bytes read in 114 ms (27.9 MiB/s) [2021-05-31 15:45:42] reading atc-gen2.dtb [2021-05-31 15:45:42] 22404 bytes read in 17 ms (1.3 MiB/s) [2021-05-31 15:45:42] ## Booting kernel from Legacy Image at 81000000 ... [2021-05-31 15:45:42] Image Name: Linux-4.1.8-rt8+gbd51baf [2021-05-31 15:45:42] Image Type: ARM Linux Kernel Image (uncompressed) [2021-05-31 15:45:42] Data Size: 3338392 Bytes = 3.2 MiB [2021-05-31 15:45:42] Load Address: 80008000 [2021-05-31 15:45:42] Entry Point: 80008000 [2021-05-31 15:45:42] Verifying Checksum ... OK [2021-05-31 15:45:43] ## Flattened Device Tree blob at 8f000000 [2021-05-31 15:45:43] Booting using the fdt blob at 0x8f000000 [2021-05-31 15:45:43] Loading Kernel Image ... OK [2021-05-31 15:45:44] Loading Device Tree to 9eec9000, end 9eed1783 ... OK [2021-05-31 15:45:44] [2021-05-31 15:45:44] Starting kernel ... [2021-05-31 15:45:44] [2021-05-31 15:45:51] Booting Linux on physical CPU 0xf00 [2021-05-31 15:45:51] Linux version 4.1.8-rt8+gbd51baf (peektraffic@ubuntu) (gcc version 5.2.0 (GCC) ) #24 SMP Mon May 31 15:22:01 IST 2021 [2021-05-31 15:45:51] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=70c5387d [2021-05-31 15:45:51] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [2021-05-31 15:45:51] Machine model: Peek ATC-GEN2 Board [2021-05-31 15:45:51] Forcing write-allocate cache policy for SMP [2021-05-31 15:45:51] Memory policy: Data cache writealloc [2021-05-31 15:45:51] psci: probing for conduit method from DT. [2021-05-31 15:45:51] psci: PSCIv1.0 detected in firmware. [2021-05-31 15:45:51] psci: Using standard PSCI v0.2 function IDs [2021-05-31 15:45:51] PERCPU: Embedded 12 pages/cpu @9fbcf000 s16640 r8192 d24320 u49152 [2021-05-31 15:45:51] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [2021-05-31 15:45:51] Kernel command line: root=/dev/mmcblk0p2 rootfstype=ext3 rootwait rw console=ttyS0,115200 [2021-05-31 15:45:51] PID hash table entries: 2048 (order: 1, 8192 bytes) [2021-05-31 15:45:51] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [2021-05-31 15:45:51] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [2021-05-31 15:45:51] Memory: 512212K/524288K available (3560K kernel code, 203K rwdata, 1624K rodata, 220K init, 195K bss, 12076K reserved, ) [2021-05-31 15:45:51] Virtual kernel memory layout: [2021-05-31 15:45:51] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [2021-05-31 15:45:51] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [2021-05-31 15:45:51] vmalloc : 0xa0800000 - 0xff000000 (1512 MB) [2021-05-31 15:45:51] lowmem : 0x80000000 - 0xa0000000 ( 512 MB) [2021-05-31 15:45:51] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [2021-05-31 15:45:51] modules : 0x7f800000 - 0x7fe00000 ( 6 MB) [2021-05-31 15:45:51] .text : 0x80008000 - 0x80518360 (5185 kB) [2021-05-31 15:45:51] .init : 0x80519000 - 0x80550000 ( 220 kB) [2021-05-31 15:45:51] .data : 0x80550000 - 0x80582d98 ( 204 kB) [2021-05-31 15:45:51] .bss : 0x80585000 - 0x805b5c70 ( 196 kB) [2021-05-31 15:45:51] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [2021-05-31 15:45:51] Hierarchical RCU implementation. [2021-05-31 15:45:51] Additional per-CPU info printed with stalls. [2021-05-31 15:45:51] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [2021-05-31 15:45:51] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [2021-05-31 15:45:51] NR_IRQS:16 nr_irqs:16 16 [2021-05-31 15:45:51] Architected cp15 timer(s) running at 12.50MHz (phys). [2021-05-31 15:45:51] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [2021-05-31 15:45:51] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [2021-05-31 15:45:51] Switching to timer-based delay loop, resolution 80ns [2021-05-31 15:45:51] Console: colour dummy device 80x30 [2021-05-31 15:45:51] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000) [2021-05-31 15:45:51] pid_max: default: 32768 minimum: 301 [2021-05-31 15:45:51] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [2021-05-31 15:45:51] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [2021-05-31 15:45:51] CPU: Testing write buffer coherency: ok [2021-05-31 15:45:51] CPU0: update cpu_capacity 1024 [2021-05-31 15:45:51] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00 [2021-05-31 15:45:51] Setting up static identity map for 0x80008280 - 0x800082e4 [2021-05-31 15:45:51] CPU1: update cpu_capacity 1024 [2021-05-31 15:45:51] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01 [2021-05-31 15:45:51] Brought up 2 CPUs [2021-05-31 15:45:51] SMP: Total of 2 processors activated (50.00 BogoMIPS). [2021-05-31 15:45:51] CPU: All CPU(s) started in HYP mode. [2021-05-31 15:45:51] CPU: Virtualization extensions available. [2021-05-31 15:45:51] devtmpfs: initialized [2021-05-31 15:45:51] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [2021-05-31 15:45:51] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [2021-05-31 15:45:51] pinctrl core: initialized pinctrl subsystem [2021-05-31 15:45:51] NET: Registered protocol family 16 [2021-05-31 15:45:51] DMA: preallocated 256 KiB pool for atomic coherent allocations [2021-05-31 15:45:51] cpuidle: using governor ladder [2021-05-31 15:45:51] cpuidle: using governor menu [2021-05-31 15:45:51] irq: no irq domain found for /soc/uqe@2400000/qeic@80 ! [2021-05-31 15:45:51] irq: no irq domain found for /soc/uqe@2400000/qeic@80 ! [2021-05-31 15:45:51] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [2021-05-31 15:45:52] hw-breakpoint: maximum watchpoint size is 8 bytes. [2021-05-31 15:45:52] register e1000-wakeup irq error, ret = -22 [2021-05-31 15:45:52] Serial: AMBA PL011 UART driver [2021-05-31 15:45:52] SCSI subsystem initialized [2021-05-31 15:45:52] Firstviw : phy_init TP1 [2021-05-31 15:45:52] Firstviw : phy_init TP2 rc=0 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_init TP4 rc=0 [2021-05-31 15:45:52] usbcore: registered new interface driver usbfs [2021-05-31 15:45:52] usbcore: registered new interface driver hub [2021-05-31 15:45:52] usbcore: registered new device driver usb [2021-05-31 15:45:52] i2c i2c-0: IMX I2C adapter registered [2021-05-31 15:45:52] i2c i2c-0: can't use DMA [2021-05-31 15:45:52] i2c i2c-1: IMX I2C adapter registered [2021-05-31 15:45:52] i2c i2c-1: can't use DMA [2021-05-31 15:45:52] pps_core: LinuxPPS API ver. 1 registered [2021-05-31 15:45:52] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [2021-05-31 15:45:52] PTP clock support registered [2021-05-31 15:45:52] Switched to clocksource arch_sys_counter [2021-05-31 15:45:52] NET: Registered protocol family 2 [2021-05-31 15:45:52] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [2021-05-31 15:45:52] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [2021-05-31 15:45:52] TCP: Hash tables configured (established 4096 bind 4096) [2021-05-31 15:45:52] UDP hash table entries: 256 (order: 1, 8192 bytes) [2021-05-31 15:45:52] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [2021-05-31 15:45:52] NET: Registered protocol family 1 [2021-05-31 15:45:52] RPC: Registered named UNIX socket transport module. [2021-05-31 15:45:52] RPC: Registered udp transport module. [2021-05-31 15:45:52] RPC: Registered tcp transport module. [2021-05-31 15:45:52] RPC: Registered tcp NFSv4.1 backchannel transport module. [2021-05-31 15:45:52] kvm [1]: interrupt-controller@1404000 IRQ22 [2021-05-31 15:45:52] kvm [1]: timer IRQ18 [2021-05-31 15:45:52] kvm [1]: Hyp mode initialized successfully [2021-05-31 15:45:52] CPU PMU: Failed to parse /pmu/interrupt-affinity[0] [2021-05-31 15:45:52] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available [2021-05-31 15:45:52] futex hash table entries: 512 (order: 3, 32768 bytes) [2021-05-31 15:45:52] HugeTLB registered 2 MB page size, pre-allocated 0 pages [2021-05-31 15:45:52] NFS: Registering the id_resolver key type [2021-05-31 15:45:52] Key type id_resolver registered [2021-05-31 15:45:52] Key type id_legacy registered [2021-05-31 15:45:52] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [2021-05-31 15:45:52] io scheduler noop registered [2021-05-31 15:45:52] io scheduler deadline registered [2021-05-31 15:45:52] io scheduler cfq registered (default) [2021-05-31 15:45:52] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [2021-05-31 15:45:52] console [ttyS0] disabled [2021-05-31 15:45:52] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 32, base_baud = 6000000) is a 16550A [2021-05-31 15:45:52] console [ttyS0] enabled [2021-05-31 15:45:52] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 32, base_baud = 6000000) is a 16550A [2021-05-31 15:45:52] 2950000.serial: ttyLP0 at MMIO 0x2950000 (irq = 38, base_baud = 4000000) is a FSL_LPUART [2021-05-31 15:45:52] fsl-lpuart 2950000.serial: DMA tx channel request failed, operating without tx DMA [2021-05-31 15:45:52] fsl-lpuart 2950000.serial: DMA rx channel request failed, operating without rx DMA [2021-05-31 15:45:52] brd: module loaded [2021-05-31 15:45:52] loop: module loaded [2021-05-31 15:45:52] of-flash 60000000.nor: do_map_probe() failed for type cfi_probe [2021-05-31 15:45:52] of-flash 60000000.nor: do_map_probe() failed [2021-05-31 15:45:52] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] Firstviw : phy_drivers_register TP1 [2021-05-31 15:45:52] Firstviw : phy_driver_register TP1 [2021-05-31 15:45:52] tun: Universal TUN/TAP device driver, 1.6 [2021-05-31 15:45:52] tun: (C) 1999-2004 Max Krasnyansky [2021-05-31 15:45:52] winston1 [2021-05-31 15:45:52] winston2 [2021-05-31 15:45:52] winston3 [2021-05-31 15:45:52] winston3 [2021-05-31 15:45:52] winston3 [2021-05-31 15:45:52] Firstview TTP1of_mdiobus_register [2021-05-31 15:45:52] libphy: Freescale PowerQUICC MII Bus: probed [2021-05-31 15:45:52] Firstview TTP1of_mdiobus_register_phy [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:8192 [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:41536 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:45:52] Firstviw : phy_probe TP1 [2021-05-31 15:45:52] Firstviw : of_set_phy_supported TP1 [2021-05-31 15:45:52] Firstviw : phy_probe TP4 [2021-05-31 15:45:52] Firstview TTP1of_mdiobus_register_phy [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:8192 [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:41536 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:45:52] Firstviw : phy_probe TP1 [2021-05-31 15:45:52] Firstviw : of_set_phy_supported TP1 [2021-05-31 15:45:52] Firstviw : phy_probe TP4 [2021-05-31 15:45:52] Firstview TTP1of_mdiobus_register_phy [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:0 [2021-05-31 15:45:52] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:52] FV TP3 fsl_pq_mdio_read value:0 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:45:52] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000: enabled errata workarounds, flags: 0x4 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: mac: 00:04:9f:05:80:bc [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: Running with NAPI enabled [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: RX BD ring size for Q[0]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: RX BD ring size for Q[1]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: TX BD ring size for Q[0]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d10000 eth0: TX BD ring size for Q[1]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000: enabled errata workarounds, flags: 0x4 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: mac: 00:04:9f:05:80:be [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: Running with NAPI enabled [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: RX BD ring size for Q[0]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: RX BD ring size for Q[1]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: TX BD ring size for Q[0]: 256 [2021-05-31 15:45:52] fsl-gianfar soc:ethernet@2d90000 eth1: TX BD ring size for Q[1]: 256 [2021-05-31 15:45:52] pps pps0: new PPS source ptp0 [2021-05-31 15:45:52] hdlc: HDLC support module revision 1.22 [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66c hci version 0x100 quirks 0x00010010 [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: irq 50, io mem 0x03100000 [2021-05-31 15:45:53] hub 1-0:1.0: USB hub found [2021-05-31 15:45:53] hub 1-0:1.0: 1 port detected [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [2021-05-31 15:45:53] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [2021-05-31 15:45:53] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [2021-05-31 15:45:53] hub 2-0:1.0: USB hub found [2021-05-31 15:45:53] hub 2-0:1.0: 1 port detected [2021-05-31 15:45:53] usbcore: registered new interface driver usb-storage [2021-05-31 15:45:53] usbcore: registered new interface driver usbserial [2021-05-31 15:45:53] usbcore: registered new interface driver usbserial_generic [2021-05-31 15:45:53] usbserial: USB Serial support registered for generic [2021-05-31 15:45:53] mousedev: PS/2 mouse device common for all mice [2021-05-31 15:45:53] i2c /dev entries driver [2021-05-31 15:45:53] ina2xx 0-0040: error configuring the device: -5 [2021-05-31 15:45:53] ina2xx 0-0041: error configuring the device: -5 [2021-05-31 15:45:53] 0-004c supply vcc not found, using dummy regulator [2021-05-31 15:45:53] lm90 0-004c: Register 0x4 read failed (-5) [2021-05-31 15:45:53] lm90 0-004c: Failed to read convrate register! [2021-05-31 15:45:53] lm90 0-004c: Register 0x3 read failed (-5) [2021-05-31 15:45:53] lm90 0-004c: Initialization failed! [2021-05-31 15:45:53] imx2-wdt 2ad0000.watchdog: timeout 60 sec (nowayout=0) [2021-05-31 15:45:53] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver [2021-05-31 15:45:53] sdhci: Secure Digital Host Controller Interface driver [2021-05-31 15:45:53] sdhci: Copyright(c) Pierre Ossman [2021-05-31 15:45:53] sdhci-pltfm: SDHCI platform and OF driver helper [2021-05-31 15:45:53] sdhci-esdhc 1560000.esdhc: No vmmc regulator found [2021-05-31 15:45:53] sdhci-esdhc 1560000.esdhc: No vqmmc regulator found [2021-05-31 15:45:53] mmc0: SDHCI controller on 1560000.esdhc [1560000.esdhc] using ADMA 64-bit [2021-05-31 15:45:53] usbcore: registered new interface driver usbhid [2021-05-31 15:45:53] usbhid: USB HID core driver [2021-05-31 15:45:53] oprofile: using timer interrupt. [2021-05-31 15:45:53] Initializing XFRM netlink socket [2021-05-31 15:45:53] NET: Registered protocol family 10 [2021-05-31 15:45:53] sit: IPv6 over IPv4 tunneling driver [2021-05-31 15:45:53] NET: Registered protocol family 17 [2021-05-31 15:45:53] NET: Registered protocol family 15 [2021-05-31 15:45:53] Key type dns_resolver registered [2021-05-31 15:45:53] Registering SWP/SWPB emulation handler [2021-05-31 15:45:53] hctosys: unable to open rtc device (rtc0) [2021-05-31 15:45:53] Waiting for root device /dev/mmcblk0p2... [2021-05-31 15:45:53] mmc0: new high speed SDHC card at address 0007 [2021-05-31 15:45:53] mmcblk0: mmc0:0007 SD8GB 7.42 GiB [2021-05-31 15:45:53] mmcblk0: p1 p2 [2021-05-31 15:45:54] kjournald starting. Commit interval 5 seconds [2021-05-31 15:45:54] EXT3-fs (mmcblk0p2): using internal journal [2021-05-31 15:45:54] EXT3-fs (mmcblk0p2): recovery complete [2021-05-31 15:45:54] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode [2021-05-31 15:45:54] VFS: Mounted root (ext3 filesystem) on device 179:2. [2021-05-31 15:45:54] devtmpfs: mounted [2021-05-31 15:45:54] Freeing unused kernel memory: 220K (80519000 - 80550000) INIT: version 2.88 booting [2021-05-31 15:45:55] Starting udev [2021-05-31 15:45:55] udev: Not using udev cache because of changes detected in the following files: [2021-05-31 15:45:55] udev: /proc/version /proc/cmdline /proc/devices [2021-05-31 15:45:55] udev: lib/udev/rules.d/* etc/udev/rules.d/* [2021-05-31 15:45:55] udev: The udev cache will be regenerated. To identify the detected changes, [2021-05-31 15:45:55] udev: compare the cached sysconf at /etc/udev/cache.data [2021-05-31 15:45:55] udev: against the current sysconf at /dev/shm/udev.cache [2021-05-31 15:45:55] udevd[106]: starting version 182 [2021-05-31 15:45:56] random: dd urandom read with 44 bits of entropy available [2021-05-31 15:45:56] Populating dev cache [2021-05-31 15:45:57] hwclock: can't open '/dev/misc/rtc': No such file or directory [2021-05-31 15:45:57] Fri Apr 16 11:21:53 UTC 2021 [2021-05-31 15:45:57] hwclock: can't open '/dev/misc/rtc': No such file or directory [2021-05-31 15:45:57] Ethernet conf application [2021-05-31 15:45:57] *** Error in `/app/eth-conf-app': free(): invalid pointer: 0x000114e9 *** INIT: Entering runlevel: 5/rcS.d/Startup-atc.sh: line 2: 270 Aborted [2021-05-31 15:45:57] Configuring network interfaces... eth0: adding address fe80::204:9fff:fe05:80bc [2021-05-31 15:45:57] eth1: adding address fe80::204:9fff:fe05:80be [2021-05-31 15:45:57] done. [2021-05-31 15:45:57] Starting OpenBSD Secure Shell server: sshd [2021-05-31 15:45:57] done. [2021-05-31 15:45:57] hwclock: can't open '/dev/misc/rtc': No such file or directory [2021-05-31 15:45:57] no interfaces hFirstview TTP1of_phy_find_device Firstview TTP d=-1635490808 of_phy_find_device [2021-05-31 15:45:57] [2021-05-31 15:45:57] forked to backFirstview : of_phy_connect phy = 9e846400 [2021-05-31 15:45:57] ground, child pFirstview : of_phy_connect phy = 9e846400 TP1 [2021-05-31 15:45:57] [2021-05-31 15:45:57] ## PHY CONNECT DIRECT [2021-05-31 15:45:57] id 321 [2021-05-31 15:45:57] Firstviw : phy_attach_direct TP1 [2021-05-31 15:45:57] Firstviw : phy_attach_direct TP12 [2021-05-31 15:45:57] Firstviw : phy_init_hw TP1 [2021-05-31 15:45:57] [2021-05-31 15:45:57] ## phy init hw [2021-05-31 15:45:57] Firstviw : phy_init_hw TP3 [2021-05-31 15:45:57] winston1 dp83822_phy_reset [2021-05-31 15:45:58] FV mdiobus_write [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP5 fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:45:58] winston1 dp83822_config_init [2021-05-31 15:45:58] Firstviw : genphy_config_init TP1 [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:58] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:45:58] Firstviw : phy_init_hw TP4 [2021-05-31 15:45:58] Firstviw : phy_init_hw TP7 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:45:58] winston1 dp83822_config_init [2021-05-31 15:45:58] Firstviw : genphy_config_init TP1 [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:58] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:45:58] Firstviw : phy_attach_direct TP13 [2021-05-31 15:45:58] Firstviw : phy_detach TP1 [2021-05-31 15:45:58] Firstviw : phy_suspend TP1 [2021-05-31 15:45:58] winston1 dp83822_get_wol [2021-05-31 15:45:58] Firstviw : phy_detach TP2 [2021-05-31 15:45:58] Firstviw : phy_detach TP2 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ## phy connect direct error rc=-95 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ### phydev=0 [2021-05-31 15:45:58] net eth0: 1could not attach to PHY [2021-05-31 15:45:58] Firstview TTP1of_phy_find_device [2021-05-31 15:45:58] Firstview TTP d=-1635491832 of_phy_find_device [2021-05-31 15:45:58] Firstview : of_phy_connect phy = 9e846000 [2021-05-31 15:45:58] Firstview : of_phy_connect phy = 9e846000 TP1 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ## PHY CONNECT DIRECT [2021-05-31 15:45:58] Firstviw : phy_attach_direct TP1 [2021-05-31 15:45:58] Firstviw : phy_attach_direct TP12 [2021-05-31 15:45:58] Firstviw : phy_init_hw TP1 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ## phy init hw [2021-05-31 15:45:58] Firstviw : phy_init_hw TP3 [2021-05-31 15:45:58] winston1 dp83822_phy_reset [2021-05-31 15:45:58] FV mdiobus_write [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP5 fsl_pq_mdio_write [2021-05-31 15:45:58] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:45:58] winston1 dp83822_config_init [2021-05-31 15:45:58] Firstviw : genphy_config_init TP1 [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:58] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:45:58] Firstviw : phy_init_hw TP4 [2021-05-31 15:45:58] Firstviw : phy_init_hw TP7 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:45:58] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:45:58] winston1 dp83822_config_init [2021-05-31 15:45:58] Firstviw : genphy_config_init TP1 [2021-05-31 15:45:58] FV TP1 fsl_pq_mdio_read [2021-05-31 15:45:58] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:45:58] Firstviw : phy_attach_direct TP13 [2021-05-31 15:45:58] Firstviw : phy_detach TP1 [2021-05-31 15:45:58] Firstviw : phy_suspend TP1 [2021-05-31 15:45:58] winston1 dp83822_get_wol [2021-05-31 15:45:58] Firstviw : phy_detach TP2 [2021-05-31 15:45:58] Firstviw : phy_detach TP2 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ## phy connect direct error rc=-95 [2021-05-31 15:45:58] [2021-05-31 15:45:58] ### phydev=0 [2021-05-31 15:45:58] net eth1: 1could not attach to PHY [2021-05-31 15:45:58] Starting syslogd/klogd: done [2021-05-31 15:45:58] * starting FTP Server: vsftpd... done. [2021-05-31 15:45:58] [2021-05-31 15:45:58] QorIQ SDK (FSL Reference Distro) 2.0 atc-gen2 /dev/ttyS0 [2021-05-31 15:45:58] atc-gen2 login: root] [2021-05-31 15:46:03] root@atc-gen2:~# [2021-05-31 15:46:05] root@atc-gen2:~# ifconfig [2021-05-31 15:46:09] lo Link encap:Local Loopback [2021-05-31 15:46:09] inet addr:127.0.0.1 Mask:255.0.0.0 [2021-05-31 15:46:09] inet6 addr: ::1/128 Scope:Host [2021-05-31 15:46:09] UP LOOPBACK RUNNING MTU:65536 Metric:1 [2021-05-31 15:46:09] RX packets:0 errors:0 dropped:0 overruns:0 frame:0 [2021-05-31 15:46:09] TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 [2021-05-31 15:46:09] collisions:0 txqueuelen:0 [2021-05-31 15:46:09] RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) [2021-05-31 15:46:09] [2021-05-31 15:46:09] root@atc-gen2:~# udhcpc -i eth0 [2021-05-31 15:46:20] udhcpc (v1.23.2) started [2021-05-31 15:46:20] Firstview TTP1of_phy_find_device [2021-05-31 15:46:20] Firstview TTP d=-1635490808 of_phy_find_device [2021-05-31 15:46:20] Firstview : of_phy_connect phy = 9e846400 [2021-05-31 15:46:20] Firstview : of_phy_connect phy = 9e846400 TP1 [2021-05-31 15:46:20] [2021-05-31 15:46:20] ## PHY CONNECT DIRECT [2021-05-31 15:46:20] Firstviw : phy_attach_direct TP1 [2021-05-31 15:46:20] Firstviw : phy_attach_direct TP12 [2021-05-31 15:46:20] Firstviw : phy_init_hw TP1 [2021-05-31 15:46:20] [2021-05-31 15:46:20] ## phy init hw [2021-05-31 15:46:20] Firstviw : phy_init_hw TP3 [2021-05-31 15:46:20] winston1 dp83822_phy_reset [2021-05-31 15:46:20] FV mdiobus_write [2021-05-31 15:46:20] FV TP1 fsl_pq_mdio_write [2021-05-31 15:46:20] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:46:20] FV TP5 fsl_pq_mdio_write [2021-05-31 15:46:20] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:46:20] winston1 dp83822_config_init [2021-05-31 15:46:20] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:20] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:20] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:20] Firstviw : phy_init_hw TP4 [2021-05-31 15:46:20] Firstviw : phy_init_hw TP7 [2021-05-31 15:46:20] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:46:20] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:46:20] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:46:20] winston1 dp83822_config_init [2021-05-31 15:46:20] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:20] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:20] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:20] Firstviw : phy_attach_direct TP13 [2021-05-31 15:46:20] Firstviw : phy_detach TP1 [2021-05-31 15:46:20] Firstviw : phy_suspend TP1 [2021-05-31 15:46:20] winston1 dp83822_get_wol [2021-05-31 15:46:20] Firstviw : phy_detach TP2 [2021-05-31 15:46:20] Firstviw : phy_detach TP2 [2021-05-31 15:46:20] [2021-05-31 15:46:20] ## phy connect direct error rc=-95 [2021-05-31 15:46:20] [2021-05-31 15:46:20] ### phydev=0 [2021-05-31 15:46:20] net eth0: 1could not attach to PHY [2021-05-31 15:46:20] ip: SIOCSIFFLAGS: No such device [2021-05-31 15:46:20] Sending discover... [2021-05-31 15:46:20] udhcpc: sendto: Network is down [2021-05-31 15:46:20] Read error: Network is down, reopening socket [2021-05-31 15:46:25] Sending discover... [2021-05-31 15:46:25] udhcpc: sendto: Network is down [2021-05-31 15:46:25] Read error: Network is down, reopening socket [2021-05-31 15:46:26] ^C [2021-05-31 15:46:26] root@atc-gen2:~# udhcpc -i eth1 [2021-05-31 15:46:28] udhcpc (v1.23.2) started [2021-05-31 15:46:28] Firstview TTP1of_phy_find_device [2021-05-31 15:46:28] Firstview TTP d=-1635491832 of_phy_find_device [2021-05-31 15:46:28] Firstview : of_phy_connect phy = 9e846000 [2021-05-31 15:46:28] Firstview : of_phy_connect phy = 9e846000 TP1 [2021-05-31 15:46:28] [2021-05-31 15:46:28] ## PHY CONNECT DIRECT [2021-05-31 15:46:28] Firstviw : phy_attach_direct TP1 [2021-05-31 15:46:28] Firstviw : phy_attach_direct TP12 [2021-05-31 15:46:28] Firstviw : phy_init_hw TP1 [2021-05-31 15:46:28] [2021-05-31 15:46:28] ## phy init hw [2021-05-31 15:46:28] Firstviw : phy_init_hw TP3 [2021-05-31 15:46:28] winston1 dp83822_phy_reset [2021-05-31 15:46:28] FV mdiobus_write [2021-05-31 15:46:28] FV TP1 fsl_pq_mdio_write [2021-05-31 15:46:28] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:46:28] FV TP5 fsl_pq_mdio_write [2021-05-31 15:46:28] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:46:28] winston1 dp83822_config_init [2021-05-31 15:46:28] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:28] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:28] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:28] Firstviw : phy_init_hw TP4 [2021-05-31 15:46:28] Firstviw : phy_init_hw TP7 [2021-05-31 15:46:28] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:46:28] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:46:28] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:46:28] winston1 dp83822_config_init [2021-05-31 15:46:28] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:28] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:28] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:28] Firstviw : phy_attach_direct TP13 [2021-05-31 15:46:28] Firstviw : phy_detach TP1 [2021-05-31 15:46:28] Firstviw : phy_suspend TP1 [2021-05-31 15:46:28] winston1 dp83822_get_wol [2021-05-31 15:46:28] Firstviw : phy_detach TP2 [2021-05-31 15:46:28] Firstviw : phy_detach TP2 [2021-05-31 15:46:28] [2021-05-31 15:46:28] ## phy connect direct error rc=-95 [2021-05-31 15:46:28] [2021-05-31 15:46:28] ### phydev=0 [2021-05-31 15:46:28] net eth1: 1could not attach to PHY [2021-05-31 15:46:28] ip: SIOCSIFFLAGS: No such device [2021-05-31 15:46:28] Sending discover... [2021-05-31 15:46:29] udhcpc: sendto: Network is down [2021-05-31 15:46:29] Read error: Network is down, reopening socket [2021-05-31 15:46:33] Sending discover... [2021-05-31 15:46:34] udhcpc: sendto: Network is down [2021-05-31 15:46:34] Read error: Network is down, reopening socket [2021-05-31 15:46:34] [2021-05-31 15:46:35] ^C [2021-05-31 15:46:35] root@atc-gen2:~# ifconfig eth0 up [2021-05-31 15:46:55] Firstview TTP1of_phy_find_device [2021-05-31 15:46:55] Firstview TTP d=-1635490808 of_phy_find_device [2021-05-31 15:46:55] Firstview : of_phy_connect phy = 9e846400 [2021-05-31 15:46:55] Firstview : of_phy_connect phy = 9e846400 TP1 [2021-05-31 15:46:55] [2021-05-31 15:46:55] ## PHY CONNECT DIRECT [2021-05-31 15:46:55] Firstviw : phy_attach_direct TP1 [2021-05-31 15:46:55] Firstviw : phy_attach_direct TP12 [2021-05-31 15:46:55] Firstviw : phy_init_hw TP1 [2021-05-31 15:46:55] [2021-05-31 15:46:55] ## phy init hw [2021-05-31 15:46:55] Firstviw : phy_init_hw TP3 [2021-05-31 15:46:55] winston1 dp83822_phy_reset [2021-05-31 15:46:55] FV mdiobus_write [2021-05-31 15:46:55] FV TP1 fsl_pq_mdio_write [2021-05-31 15:46:55] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:46:55] FV TP5 fsl_pq_mdio_write [2021-05-31 15:46:55] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:46:55] winston1 dp83822_config_init [2021-05-31 15:46:55] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:55] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:55] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:55] Firstviw : phy_init_hw TP4 [2021-05-31 15:46:55] Firstviw : phy_init_hw TP7 [2021-05-31 15:46:55] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:46:55] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:46:55] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:46:55] winston1 dp83822_config_init [2021-05-31 15:46:55] Firstviw : genphy_config_init TP1 [2021-05-31 15:46:55] FV TP1 fsl_pq_mdio_read [2021-05-31 15:46:55] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:46:55] Firstviw : phy_attach_direct TP13 [2021-05-31 15:46:55] Firstviw : phy_detach TP1 [2021-05-31 15:46:55] Firstviw : phy_suspend TP1 [2021-05-31 15:46:55] winston1 dp83822_get_wol [2021-05-31 15:46:55] Firstviw : phy_detach TP2 [2021-05-31 15:46:55] Firstviw : phy_detach TP2 [2021-05-31 15:46:55] [2021-05-31 15:46:55] ## phy connect direct error rc=-95 [2021-05-31 15:46:55] [2021-05-31 15:46:55] ### phydev=0 [2021-05-31 15:46:55] net eth0: 1could not attach to PHY [2021-05-31 15:46:55] ifconfig: SIOCSIFFLAGS: No such device [2021-05-31 15:46:55] root@atc-gen2:~# random: nonblocking pool is initialized [2021-05-31 15:47:15] ifconfig eth1 up [2021-05-31 15:47:19] Firstview TTP1of_phy_find_device [2021-05-31 15:47:19] Firstview TTP d=-1635491832 of_phy_find_device [2021-05-31 15:47:19] Firstview : of_phy_connect phy = 9e846000 [2021-05-31 15:47:19] Firstview : of_phy_connect phy = 9e846000 TP1 [2021-05-31 15:47:19] [2021-05-31 15:47:19] ## PHY CONNECT DIRECT [2021-05-31 15:47:19] Firstviw : phy_attach_direct TP1 [2021-05-31 15:47:19] Firstviw : phy_attach_direct TP12 [2021-05-31 15:47:19] Firstviw : phy_init_hw TP1 [2021-05-31 15:47:19] [2021-05-31 15:47:19] ## phy init hw [2021-05-31 15:47:19] Firstviw : phy_init_hw TP3 [2021-05-31 15:47:19] winston1 dp83822_phy_reset [2021-05-31 15:47:19] FV mdiobus_write [2021-05-31 15:47:19] FV TP1 fsl_pq_mdio_write [2021-05-31 15:47:19] FV TP4 timeout:1000, fsl_pq_mdio_write [2021-05-31 15:47:19] FV TP5 fsl_pq_mdio_write [2021-05-31 15:47:19] FV TP6 fsl_pq_mdio_write ret:0 [2021-05-31 15:47:19] winston1 dp83822_config_init [2021-05-31 15:47:19] Firstviw : genphy_config_init TP1 [2021-05-31 15:47:19] FV TP1 fsl_pq_mdio_read [2021-05-31 15:47:19] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:47:19] Firstviw : phy_init_hw TP4 [2021-05-31 15:47:19] Firstviw : phy_init_hw TP7 [2021-05-31 15:47:19] Firstviw : phy_scan_fixups TP1 [2021-05-31 15:47:19] Firstviw : phy_scan_fixups TP2 [2021-05-31 15:47:19] Firstviw : phy_scan_fixups TP7 [2021-05-31 15:47:19] winston1 dp83822_config_init [2021-05-31 15:47:19] Firstviw : genphy_config_init TP1 [2021-05-31 15:47:19] FV TP1 fsl_pq_mdio_read [2021-05-31 15:47:19] FV TP3 fsl_pq_mdio_read value:30793 [2021-05-31 15:47:19] Firstviw : phy_attach_direct TP13 [2021-05-31 15:47:19] Firstviw : phy_detach TP1 [2021-05-31 15:47:19] Firstviw : phy_suspend TP1 [2021-05-31 15:47:19] winston1 dp83822_get_wol [2021-05-31 15:47:19] Firstviw : phy_detach TP2 [2021-05-31 15:47:19] Firstviw : phy_detach TP2 [2021-05-31 15:47:19] [2021-05-31 15:47:19] ## phy connect direct error rc=-95 [2021-05-31 15:47:19] [2021-05-31 15:47:19] ### phydev=0 [2021-05-31 15:47:19] net eth1: 1could not attach to PHY [2021-05-31 15:47:19] ifconfig: SIOCSIFFLAGS: No such device [2021-05-31 15:47:19] root@atc-gen2:~# CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.7.1 | VT102 | Offline | ttyUSB0