NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 00:41:58, Jul 30 2019 NOTICE: UDIMM 18ADF2G72AZ-3G2E1 NOTICE: DDR4 UDIMM with 2-rank 64-bit bus (x8) NOTICE: 32 GB DDR4, 64-bit, CL=22, ECC on, 256B, CS0+CS1 NOTICE: BL2: Booting BL31 NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 00:42:06, Jul 30 2019 NOTICE: Welcome to LX2160 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:38:31 +0800) SoC: LX2160ACE Rev1.0 (0x87360010) Clock Configuration: CPU0(A72):2000 MHz CPU1(A72):2000 MHz CPU2(A72):2000 MHz CPU3(A72):2000 MHz CPU4(A72):2000 MHz CPU5(A72):2000 MHz CPU6(A72):2000 MHz CPU7(A72):2000 MHz CPU8(A72):2000 MHz CPU9(A72):2000 MHz CPU10(A72):2000 MHz CPU11(A72):2000 MHz CPU12(A72):2000 MHz CPU13(A72):2000 MHz CPU14(A72):2000 MHz CPU15(A72):2000 MHz Bus: 700 MHz DDR: 2900 MT/s Reset Configuration Word (RCW): 00000000: 50777738 1c500050 00000000 00000000 00000010: 00000000 0c010000 00000000 00000000 00000020: 022001a0 00002580 00000000 00000096 00000030: 00000000 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 08b30010 001d0020 Model: NXP Layerscape LX2160ARDB Board Board: LX2160ACE Rev1.0-RDB, Board version: B, boot from FlexSPI DEV#1 FPGA: v4.0 SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz SERDES3 Reference: Clock1 = 100MHz Clock2 = 100Hz I2C: ready VID: Core voltage after adjustment is at 801 mV DRAM: 31.9 GiB DDR 31.9 GiB (DDR4, 64-bit, CL=22, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 Using SERDES1 Protocol: 19 (0x13) Using SERDES2 Protocol: 5 (0x5) Using SERDES3 Protocol: 2 (0x2) MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected mt35xu512g with page size 256 Bytes, erase size 128 KiB, total 64 MiB OK EEPROM: NXID v1 In: serial_pl01x Out: serial_pl01x Err: serial_pl01x Net: CS4223: Using software initialization... CS4223: edc/gain/equalization settings: host: CX/4dB/4dB, line: SR/4dB/4dB DPMAC3@xgmii running firmware version 3.5.A DPMAC3@xgmii: system interface USXGMII DPMAC3@xgmii: Aquantia AQR107 Firmware Version 3.5.a DPMAC4@xgmii running firmware version 3.5.A DPMAC4@xgmii: system interface USXGMII DPMAC4@xgmii: Aquantia AQR107 Firmware Version 3.5.a FSL_MDIO1:0 is connected to DPMAC5@25g-aui. Reconnecting to DPMAC6@25g-aui PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: no link PCIe3: pcie@3700000 disabled PCIe4: pcie@3800000 Root Complex: no link PCIe5: pcie@3900000 disabled DPMAC2@xlaui4, DPMAC3@xgmii, DPMAC4@xgmii, DPMAC5@25g-aui, DPMAC6@25g-aui, DPMAC17@rgmii-id, DPMAC18@rgmii-id crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 0 starting USB... USB0: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 USB1: Register 200017f NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device scanning bus for devices... SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Target spinup took 0 ms. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Device 0: (0:0) Vendor: ATA Prod.: INTEL SSDSC2BB24 Rev: N201 Type: Hard Disk Capacity: 228936.5 MB = 223.5 GB (468862128 x 512) SATA link 0 timeout. AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst Device 0: (0:0) Vendor: ATA Prod.: INTEL SSDSC2BB24 Rev: N201 Type: Hard Disk Capacity: 228936.5 MB = 223.5 GB (468862128 x 512) ... is now current device ** Unrecognized filesystem type ** Scanning scsi 0:2... Found U-Boot script /lx2160ardb_boot.scr 980 bytes read in 3 ms (318.4 KiB/s) ## Executing script at 80000000 36745728 bytes read in 582 ms (60.2 MiB/s) 32643 bytes read in 3 ms (10.4 MiB/s) ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Device Tree to 000000009fff5000, end 000000009fffff82 ... OK fsl-mc: Deploying data path layout ... SUCCESS Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.4.3 (jenkins@saturn) (gcc version 7.5.0 (Ubuntu/Linaro 7.5.0-3ubuntu1~18.04)) #2 SMP PREEMPT Thu Apr 9 04:37:43 CST 2020 [ 0.000000] Machine model: NXP Layerscape LX2160ARDB [ 0.000000] earlycon: pl11 at MMIO32 0x00000000021c0000 (options '') [ 0.000000] printk: bootconsole [pl11] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 320 MiB at 0x00000000e7c00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000277fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x277c3df800-0x277c3e0fff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000277fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x000000277fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000277fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 24 pages/cpu s59928 r8192 d30184 u98304 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 7724544 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyAMA0,115200 earlycon=pl011,mmio32,0x21c0000 root=PARTUUID=8fa3bcf9-04 rw rootwait pci=pcie_bus_perf isolcpus=1-15 [ 0.000000] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) [ 0.000000] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0xe3c00000-0xe7c00000] (64MB) [ 0.000000] Memory: 30355296K/31389696K available (18620K kernel code, 2476K rwdata, 8844K rodata, 5888K init, 993K bss, 706720K reserved, 327680K cma-reserved) [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006200000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @275ac80000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x000000275ac70000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x000000275ad00000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2b8/0x458 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008393] Console: colour dummy device 80x25 [ 0.012923] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023390] pid_max: default: 32768 minimum: 301 [ 0.028136] LSM: Security Framework initializing [ 0.032931] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.040670] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.072800] ASID allocator initialised with 32768 entries [ 0.086266] rcu: Hierarchical SRCU implementation. [ 0.099141] Platform MSI: gic-its@6020000 domain created [ 0.104547] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.112134] fsl-mc MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.120319] EFI services will not be available. [ 0.132905] smp: Bringing up secondary CPUs ... [ 0.169620] Detected PIPT I-cache on CPU1 [ 0.169636] GICv3: CPU1: found redistributor 1 region 0:0x0000000006220000 [ 0.169647] GICv3: CPU1: using allocated LPI pending table @0x000000275ad10000 [ 0.169663] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.201635] Detected PIPT I-cache on CPU2 [ 0.201650] GICv3: CPU2: found redistributor 100 region 0:0x0000000006240000 [ 0.201662] GICv3: CPU2: using allocated LPI pending table @0x000000275ad20000 [ 0.201678] CPU2: Booted secondary processor 0x0000000100 [0x410fd083] [ 0.233656] Detected PIPT I-cache on CPU3 [ 0.233666] GICv3: CPU3: found redistributor 101 region 0:0x0000000006260000 [ 0.233677] GICv3: CPU3: using allocated LPI pending table @0x000000275ad30000 [ 0.233690] CPU3: Booted secondary processor 0x0000000101 [0x410fd083] [ 0.265686] Detected PIPT I-cache on CPU4 [ 0.265701] GICv3: CPU4: found redistributor 200 region 0:0x0000000006280000 [ 0.265712] GICv3: CPU4: using allocated LPI pending table @0x000000275ad40000 [ 0.265728] CPU4: Booted secondary processor 0x0000000200 [0x410fd083] [ 0.297709] Detected PIPT I-cache on CPU5 [ 0.297721] GICv3: CPU5: found redistributor 201 region 0:0x00000000062a0000 [ 0.297732] GICv3: CPU5: using allocated LPI pending table @0x000000275ad50000 [ 0.297745] CPU5: Booted secondary processor 0x0000000201 [0x410fd083] [ 0.329740] Detected PIPT I-cache on CPU6 [ 0.329756] GICv3: CPU6: found redistributor 300 region 0:0x00000000062c0000 [ 0.329767] GICv3: CPU6: using allocated LPI pending table @0x000000275ad60000 [ 0.329783] CPU6: Booted secondary processor 0x0000000300 [0x410fd083] [ 0.361762] Detected PIPT I-cache on CPU7 [ 0.361775] GICv3: CPU7: found redistributor 301 region 0:0x00000000062e0000 [ 0.361786] GICv3: CPU7: using allocated LPI pending table @0x000000275ad70000 [ 0.361799] CPU7: Booted secondary processor 0x0000000301 [0x410fd083] [ 0.393794] Detected PIPT I-cache on CPU8 [ 0.393811] GICv3: CPU8: found redistributor 400 region 0:0x0000000006300000 [ 0.393824] GICv3: CPU8: using allocated LPI pending table @0x000000275ad80000 [ 0.393840] CPU8: Booted secondary processor 0x0000000400 [0x410fd083] [ 0.425816] Detected PIPT I-cache on CPU9 [ 0.425831] GICv3: CPU9: found redistributor 401 region 0:0x0000000006320000 [ 0.425842] GICv3: CPU9: using allocated LPI pending table @0x000000275ad90000 [ 0.425856] CPU9: Booted secondary processor 0x0000000401 [0x410fd083] [ 0.457856] Detected PIPT I-cache on CPU10 [ 0.457875] GICv3: CPU10: found redistributor 500 region 0:0x0000000006340000 [ 0.457888] GICv3: CPU10: using allocated LPI pending table @0x000000275ada0000 [ 0.457904] CPU10: Booted secondary processor 0x0000000500 [0x410fd083] [ 0.489872] Detected PIPT I-cache on CPU11 [ 0.489889] GICv3: CPU11: found redistributor 501 region 0:0x0000000006360000 [ 0.489900] GICv3: CPU11: using allocated LPI pending table @0x000000275adb0000 [ 0.489913] CPU11: Booted secondary processor 0x0000000501 [0x410fd083] [ 0.521905] Detected PIPT I-cache on CPU12 [ 0.521926] GICv3: CPU12: found redistributor 600 region 0:0x0000000006380000 [ 0.521938] GICv3: CPU12: using allocated LPI pending table @0x000000275adc0000 [ 0.521955] CPU12: Booted secondary processor 0x0000000600 [0x410fd083] [ 0.553928] Detected PIPT I-cache on CPU13 [ 0.553946] GICv3: CPU13: found redistributor 601 region 0:0x00000000063a0000 [ 0.553957] GICv3: CPU13: using allocated LPI pending table @0x000000275add0000 [ 0.553970] CPU13: Booted secondary processor 0x0000000601 [0x410fd083] [ 0.585961] Detected PIPT I-cache on CPU14 [ 0.585983] GICv3: CPU14: found redistributor 700 region 0:0x00000000063c0000 [ 0.585995] GICv3: CPU14: using allocated LPI pending table @0x000000275ade0000 [ 0.586012] CPU14: Booted secondary processor 0x0000000700 [0x410fd083] [ 0.617982] Detected PIPT I-cache on CPU15 [ 0.618001] GICv3: CPU15: found redistributor 701 region 0:0x00000000063e0000 [ 0.618012] GICv3: CPU15: using allocated LPI pending table @0x000000275adf0000 [ 0.618025] CPU15: Booted secondary processor 0x0000000701 [0x410fd083] [ 0.618064] smp: Brought up 1 node, 16 CPUs [ 1.000130] SMP: Total of 16 processors activated. [ 1.005002] CPU features: detected: 32-bit EL0 Support [ 1.010202] CPU features: detected: CRC32 instructions [ 1.027079] CPU: All CPU(s) started at EL2 [ 1.031244] alternatives: patching kernel code [ 1.036316] devtmpfs: initialized [ 1.044117] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 1.053974] futex hash table entries: 4096 (order: 6, 262144 bytes, linear) [ 1.063572] xor: measuring software checksum speed [ 1.108443] 8regs : 8463.000 MB/sec [ 1.152684] 32regs : 8535.000 MB/sec [ 1.196926] arm64_neon: 8465.000 MB/sec [ 1.201149] xor: using function: 32regs (8535.000 MB/sec) [ 1.206608] pinctrl core: initialized pinctrl subsystem [ 1.212299] DMI not present or invalid. [ 1.216329] NET: Registered protocol family 16 [ 1.221440] DMA: preallocated 256 KiB pool for atomic allocations [ 1.227601] audit: initializing netlink subsys (disabled) [ 1.233485] cpuidle: using governor menu [ 1.237588] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 1.244459] audit: type=2000 audit(1.032:1): state=initialized audit_enabled=0 res=1 [ 1.252820] Serial: AMBA PL011 UART driver [ 1.256997] imx mu driver is registered. [ 1.260965] imx rpmsg driver is registered. [ 1.266028] Machine: NXP Layerscape LX2160ARDB [ 1.270519] SoC family: QorIQ LX2160A [ 1.274212] SoC ID: svr:0x87360010, Revision: 1.0 [ 1.280071] 21c0000.serial: ttyAMA0 at MMIO 0x21c0000 (irq = 20, base_baud = 0) is a SBSA [ 1.288345] printk: console [ttyAMA0] enabled [ 1.288345] printk: console [ttyAMA0] enabled [ 1.297087] printk: bootconsole [pl11] disabled [ 1.297087] printk: bootconsole [pl11] disabled [ 1.306412] sbsa-uart 21d0000.serial: aliased and non-aliased serial devices found in device tree. Serial port enumeration may be unpredictable. [ 1.319356] 21d0000.serial: ttyAMA1 at MMIO 0x21d0000 (irq = 21, base_baud = 0) is a SBSA [ 1.331585] fsl_mc_bus 80c000000.fsl-mc: MC firmware version: 10.16.2 [ 1.340612] fsl_mc_dprc dprc.1: DMA mask not set [ 1.353336] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 1.360038] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 1.366747] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 1.373447] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 1.388153] cryptd: max_cpu_qlen set to 1000 [ 1.472486] raid6: neonx8 gen() 4848 MB/s [ 1.544790] raid6: neonx8 xor() 4182 MB/s [ 1.617094] raid6: neonx4 gen() 4081 MB/s [ 1.689401] raid6: neonx4 xor() 3869 MB/s [ 1.761705] raid6: neonx2 gen() 3204 MB/s [ 1.834002] raid6: neonx2 xor() 3648 MB/s [ 1.906316] raid6: neonx1 gen() 2454 MB/s [ 1.978616] raid6: neonx1 xor() 2745 MB/s [ 2.050932] raid6: int64x8 gen() 2179 MB/s [ 2.123252] raid6: int64x8 xor() 1791 MB/s [ 2.195553] raid6: int64x4 gen() 2396 MB/s [ 2.267859] raid6: int64x4 xor() 1806 MB/s [ 2.340153] raid6: int64x2 gen() 1682 MB/s [ 2.412449] raid6: int64x2 xor() 1634 MB/s [ 2.484770] raid6: int64x1 gen() 1229 MB/s [ 2.557083] raid6: int64x1 xor() 1105 MB/s [ 2.561343] raid6: using algorithm neonx8 gen() 4848 MB/s [ 2.566730] raid6: .... xor() 4182 MB/s, rmw enabled [ 2.571684] raid6: using neon recovery algorithm [ 2.576495] ACPI: Interpreter disabled. [ 2.584331] iommu: Default domain type: Passthrough [ 2.589352] vgaarb: loaded [ 2.592186] SCSI subsystem initialized [ 2.600029] usbcore: registered new interface driver usbfs [ 2.605520] usbcore: registered new interface driver hub [ 2.610880] usbcore: registered new device driver usb [ 2.616094] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 2.623388] i2c i2c-0: IMX I2C adapter registered [ 2.628153] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported [ 2.635430] i2c i2c-1: IMX I2C adapter registered [ 2.640312] mc: Linux media interface: v0.10 [ 2.644583] videodev: Linux video capture interface: v2.00 [ 2.650095] pps_core: LinuxPPS API ver. 1 registered [ 2.655052] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.664184] PTP clock support registered [ 2.668133] EDAC MC: Ver: 3.0.0 [ 2.675552] No BMan portals available! [ 2.679442] QMan: Allocated lookup table at (____ptrval____), entry count 65537 [ 2.686801] No QMan portals available! [ 2.690621] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree [ 2.700686] FPGA manager framework [ 2.704114] Advanced Linux Sound Architecture Driver Initialized. [ 2.710621] clocksource: Switched to clocksource arch_sys_counter [ 2.716810] VFS: Disk quotas dquot_6.6.0 [ 2.720753] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 2.727690] pnp: PnP ACPI: disabled [ 2.733459] thermal_sys: Registered thermal governor 'step_wise' [ 2.733461] thermal_sys: Registered thermal governor 'power_allocator' [ 2.739656] NET: Registered protocol family 2 [ 2.750733] tcp_listen_portaddr_hash hash table entries: 16384 (order: 6, 262144 bytes, linear) [ 2.759589] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 2.768473] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 2.776268] TCP: Hash tables configured (established 262144 bind 65536) [ 2.782953] UDP hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 2.790121] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 2.797856] NET: Registered protocol family 1 [ 2.814394] RPC: Registered named UNIX socket transport module. [ 2.820307] RPC: Registered udp transport module. [ 2.825007] RPC: Registered tcp transport module. [ 2.829701] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.836134] PCI: CLS 0 bytes, default 64 [ 2.840831] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 2.849115] kvm [1]: IPA Size Limit: 44bits [ 2.853642] kvm [1]: vgic-v2@c0e0000 [ 2.857231] kvm [1]: GIC system register CPU interface enabled [ 2.863228] kvm [1]: vgic interrupt IRQ1 [ 2.867314] kvm [1]: Hyp mode initialized successfully [ 2.875142] Initialise system trusted keyrings [ 2.879639] workingset: timestamp_bits=44 max_order=23 bucket_order=0 [ 2.886516] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.896490] NFS: Registering the id_resolver key type [ 2.901546] Key type id_resolver registered [ 2.905731] Key type id_legacy registered [ 2.909744] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.916469] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 2.922664] fuse: init (API version 7.31) [ 2.926743] 9p: Installing v9fs 9p2000 file system support [ 2.939129] Key type asymmetric registered [ 2.943223] Asymmetric key parser 'x509' registered [ 2.948108] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 2.959564] io scheduler mq-deadline registered [ 2.964093] io scheduler kyber registered [ 2.971449] layerscape-pcie-gen4 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 2.979204] layerscape-pcie-gen4 3600000.pcie: MEM 0x9040000000..0x907fffffff -> 0x40000000 [ 3.987861] layerscape-pcie-gen4 3600000.pcie: link never came up [ 3.994146] layerscape-pcie-gen4 3600000.pcie: link bring-up failed [ 4.000448] layerscape-pcie-gen4 3600000.pcie: Fail to probe [ 4.006130] layerscape-pcie-gen4: probe of 3600000.pcie failed with error -110 [ 4.013384] layerscape-pcie-gen4 3800000.pcie: host bridge /soc/pcie@3800000 ranges: [ 4.021124] layerscape-pcie-gen4 3800000.pcie: MEM 0xa040000000..0xa07fffffff -> 0x40000000 [ 5.029767] layerscape-pcie-gen4 3800000.pcie: link never came up [ 5.035870] layerscape-pcie-gen4 3800000.pcie: link bring-up failed [ 5.042127] layerscape-pcie-gen4 3800000.pcie: Fail to probe [ 5.047788] layerscape-pcie-gen4: probe of 3800000.pcie failed with error -110 [ 5.059277] EINJ: ACPI disabled. [ 5.064495] Bus freq driver module loaded [ 5.070715] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 5.077713] SuperH (H)SCI(F) driver initialized [ 5.082418] msm_serial: driver initialized [ 5.087462] arm-smmu 5000000.iommu: probing hardware configuration... [ 5.093897] arm-smmu 5000000.iommu: SMMUv2 with: [ 5.098513] arm-smmu 5000000.iommu: stage 1 translation [ 5.103822] arm-smmu 5000000.iommu: stage 2 translation [ 5.109124] arm-smmu 5000000.iommu: nested translation [ 5.114339] arm-smmu 5000000.iommu: coherent table walk [ 5.119641] arm-smmu 5000000.iommu: (IDR0.CTTW overridden by FW configuration) [ 5.126940] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 5.134066] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 5.140599] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 5.147031] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 5.153461] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 5.164809] brd: module loaded [ 5.172113] loop: module loaded [ 5.188133] imx ahci driver is registered. [ 5.192365] ahci-qoriq 3200000.sata: 3200000.sata supply ahci not found, using dummy regulator [ 5.200998] ahci-qoriq 3200000.sata: 3200000.sata supply phy not found, using dummy regulator [ 5.209533] ahci-qoriq 3200000.sata: 3200000.sata supply target not found, using dummy regulator [ 5.218369] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.227320] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 5.241227] scsi host0: ahci-qoriq [ 5.244709] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 28 [ 5.252687] ahci-qoriq 3210000.sata: 3210000.sata supply ahci not found, using dummy regulator [ 5.261310] ahci-qoriq 3210000.sata: 3210000.sata supply phy not found, using dummy regulator [ 5.269849] ahci-qoriq 3210000.sata: 3210000.sata supply target not found, using dummy regulator [ 5.278682] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.287639] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 5.301495] scsi host1: ahci-qoriq [ 5.304958] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 29 [ 5.312931] ahci-qoriq 3220000.sata: 3220000.sata supply ahci not found, using dummy regulator [ 5.321567] ahci-qoriq 3220000.sata: 3220000.sata supply phy not found, using dummy regulator [ 5.330122] ahci-qoriq 3220000.sata: 3220000.sata supply target not found, using dummy regulator [ 5.338946] ahci-qoriq 3220000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.347896] ahci-qoriq 3220000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 5.361794] scsi host2: ahci-qoriq [ 5.365257] ata3: SATA max UDMA/133 mmio [mem 0x03220000-0x0322ffff] port 0x100 irq 30 [ 5.373230] ahci-qoriq 3230000.sata: 3230000.sata supply ahci not found, using dummy regulator [ 5.381865] ahci-qoriq 3230000.sata: 3230000.sata supply phy not found, using dummy regulator [ 5.390423] ahci-qoriq 3230000.sata: 3230000.sata supply target not found, using dummy regulator [ 5.399244] ahci-qoriq 3230000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 5.408194] ahci-qoriq 3230000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 5.422057] scsi host3: ahci-qoriq [ 5.425521] ata4: SATA max UDMA/133 mmio [mem 0x03230000-0x0323ffff] port 0x100 irq 31 [ 5.434390] spi-nor spi0.0: found mt35xu512aba, expected m25p80 [ 5.440310] spi-nor spi0.0: mt35xu512aba (65536 Kbytes) [ 5.471152] spi-nor spi0.1: found mt35xu512aba, expected m25p80 [ 5.477069] spi-nor spi0.1: mt35xu512aba (65536 Kbytes) [ 5.483634] libphy: Fixed MDIO Bus: probed [ 5.488030] tun: Universal TUN/TAP device driver, 1.6 [ 5.493341] thunder_xcv, ver 1.0 [ 5.496588] thunder_bgx, ver 1.0 [ 5.499822] nicpf, ver 1.0 [ 5.502687] libphy: Freescale XGMAC MDIO Bus: probed [ 5.515603] libphy: Freescale XGMAC MDIO Bus: probed [ 5.524979] Freescale FM module, FMD API version 21.1.0 [ 5.530272] Freescale FM Ports module [ 5.533933] fsl_mac: fsl_mac: FSL FMan MAC API based driver [ 5.539560] fsl_dpa: FSL DPAA Ethernet driver [ 5.543940] fsl_advanced: FSL DPAA Advanced drivers: [ 5.548904] fsl_proxy: FSL DPAA Proxy initialization driver [ 5.554504] fsl_oh: FSL FMan Offline Parsing port driver [ 5.560054] hclge is initializing [ 5.563372] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 5.570593] hns3: Copyright (c) 2017 Huawei Corporation. [ 5.575921] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 5.582966] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 5.588720] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 5.594549] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 5.600470] ata1: SATA link down (SStatus 0 SControl 300) [ 5.605891] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k [ 5.612847] igb: Copyright (c) 2007-2014 Intel Corporation. [ 5.618431] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 5.626254] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 5.632283] sky2: driver version 1.30 [ 5.636140] usbcore: registered new interface driver r8152 [ 5.641636] usbcore: registered new interface driver asix [ 5.647044] usbcore: registered new interface driver ax88179_178a [ 5.653310] VFIO - User Level meta-driver version: 0.3 [ 5.662606] dwc3 3100000.usb: Failed to get clk 'ref': -2 [ 5.668010] ata2: SATA link down (SStatus 0 SControl 300) [ 5.673680] dwc3 3110000.usb: Failed to get clk 'ref': -2 [ 5.679685] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.686221] ehci-pci: EHCI PCI platform driver [ 5.690669] ehci-platform: EHCI generic platform driver [ 5.695934] ehci-orion: EHCI orion driver [ 5.699967] ehci-exynos: EHCI EXYNOS driver [ 5.704178] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.710359] ohci-pci: OHCI PCI platform driver [ 5.714808] ohci-platform: OHCI generic platform driver [ 5.720066] ohci-exynos: OHCI EXYNOS driver [ 5.724370] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.729864] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.737584] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010810 [ 5.746991] xhci-hcd xhci-hcd.0.auto: irq 26, io mem 0x03100000 [ 5.753174] hub 1-0:1.0: USB hub found [ 5.756931] hub 1-0:1.0: 1 port detected [ 5.760957] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.766448] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.774106] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 5.780805] hub 2-0:1.0: USB hub found [ 5.784560] hub 2-0:1.0: 1 port detected [ 5.788611] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.794105] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 5.801763] ata4: SATA link down (SStatus 0 SControl 300) [ 5.807246] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010810 [ 5.816645] xhci-hcd xhci-hcd.1.auto: irq 27, io mem 0x03110000 [ 5.822792] hub 3-0:1.0: USB hub found [ 5.826537] hub 3-0:1.0: 1 port detected [ 5.830553] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.836041] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 5.843709] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 5.850409] hub 4-0:1.0: USB hub found [ 5.854165] hub 4-0:1.0: 1 port detected [ 5.858275] usbcore: registered new interface driver usb-storage [ 5.865407] ftm-alarm 2800000.timer: registered as rtc1 [ 5.875736] rtc-pcf2127-i2c 1-0051: registered as rtc0 [ 5.881116] i2c /dev entries driver [ 5.885634] i2c i2c-0: Added multiplexed i2c bus 2 [ 5.890488] i2c i2c-0: Added multiplexed i2c bus 3 [ 5.895432] i2c i2c-0: Added multiplexed i2c bus 4 [ 5.900396] i2c i2c-0: Added multiplexed i2c bus 5 [ 5.905249] i2c i2c-0: Added multiplexed i2c bus 6 [ 5.910108] i2c i2c-0: Added multiplexed i2c bus 7 [ 5.914900] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 5.921152] i2c i2c-0: Added multiplexed i2c bus 8 [ 5.925956] ata3.00: ATA-10: INTEL SSDSC2BB240G7, N2010101, max UDMA/133 [ 5.932678] ata3.00: 468862128 sectors, multi 1: LBA48 NCQ (depth 32) [ 5.939189] i2c i2c-0: Added multiplexed i2c bus 9 [ 5.943974] pca954x 0-0077: registered 8 multiplexed busses for I2C mux pca9547 [ 5.951645] ata3.00: configured for UDMA/133 [ 5.956816] sbsa-gwdt 23a0000.watchdog: Initialized with 30s timeout @ 25000050 Hz, action=0. [ 5.966104] scsi 2:0:0:0: Direct-Access ATA INTEL SSDSC2BB24 0101 PQ: 0 ANSI: 5 [ 5.974349] ata3.00: Enabling discard_zeroes_data [ 5.979119] sd 2:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB) [ 5.986595] sd 2:0:0:0: [sda] 4096-byte physical blocks [ 5.993260] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver [ 5.999926] sd 2:0:0:0: [sda] Write Protect is off [ 6.005285] sdhci: Secure Digital Host Controller Interface driver [ 6.011504] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.020551] sdhci: Copyright(c) Pierre Ossman [ 6.025046] Synopsys Designware Multimedia Card Interface Driver [ 6.031224] ata3.00: Enabling discard_zeroes_data [ 6.036414] sdhci-pltfm: SDHCI platform and OF driver helper [ 6.046291] sda: sda1 sda2 sda3 sda4 [ 6.050557] ata3.00: Enabling discard_zeroes_data [ 6.055375] sd 2:0:0:0: [sda] Attached SCSI disk [ 6.083179] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 6.120616] mmc1: SDHCI controller on 2150000.esdhc [2150000.esdhc] using ADMA 64-bit [ 6.129254] ledtrig-cpu: registered to indicate activity on CPUs [ 6.136026] caam 8000000.crypto: device ID = 0x0a1a020000000000 (Era 10) [ 6.142747] caam 8000000.crypto: job rings = 3, qi = 1 [ 6.167115] caam algorithms registered in /proc/crypto [ 6.173362] caam 8000000.crypto: caam pkc algorithms registered in /proc/crypto [ 6.181156] caam_jr 8010000.jr: registering rng-caam [ 6.199121] usbcore: registered new interface driver usbhid [ 6.204734] usbhid: USB HID core driver [ 6.209088] No fsl,qman node [ 6.211974] Freescale USDPAA process driver [ 6.216162] fsl-usdpaa: no region found [ 6.220001] Freescale USDPAA process IRQ driver [ 6.225679] optee: probing for conduit method from DT. [ 6.230844] optee: api uid mismatch [ 6.236355] NET: Registered protocol family 26 [ 6.240813] u32 classifier [ 6.243519] input device check on [ 6.247232] Actions configured [ 6.252114] Initializing XFRM netlink socket [ 6.257467] NET: Registered protocol family 10 [ 6.267000] Segment Routing with IPv6 [ 6.270767] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 6.285233] NET: Registered protocol family 17 [ 6.290696] NET: Registered protocol family 15 [ 6.297278] Bridge firewalling registered [ 6.307942] mmc1: new HS400 MMC card at address 0001 [ 6.317209] mmcblk1: mmc1:0001 R1J59E 116 GiB [ 6.321679] 8021q: 802.1Q VLAN Support v1.8 [ 6.325860] lib80211: common routines for IEEE802.11 drivers [ 6.331671] mmcblk1boot0: mmc1:0001 R1J59E partition 1 8.00 MiB [ 6.337745] mmcblk1boot1: mmc1:0001 R1J59E partition 2 8.00 MiB [ 6.343699] 9pnet: Installing 9P2000 support [ 6.347978] tsn generic netlink module v1 init... [ 6.352732] mmcblk1rpmb: mmc1:0001 R1J59E partition 3 4.00 MiB, chardev (508:0) [ 6.360105] Key type dns_resolver registered [ 6.364812] registered taskstats version 1 [ 6.368906] Loading compiled-in X.509 certificates [ 6.374603] Btrfs loaded, crc32c=crc32c-generic [ 6.382105] fsl_mc_dprc dprc.1: Adding to iommu group 0 [ 6.441197] fsl_dpaa2_eth dpni.1: Adding to iommu group 0 [ 6.446630] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.453022] fsl_dpaa2_eth dpni.0: Adding to iommu group 0 [ 6.458444] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.464838] fsl_mc_allocator dpbp.1: Adding to iommu group 0 [ 6.470536] fsl_mc_allocator dpbp.0: Adding to iommu group 0 [ 6.476239] dpaa2_mac dpmac.18: Adding to iommu group 0 [ 6.481467] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.487857] dpaa2_mac dpmac.17: Adding to iommu group 0 [ 6.493086] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.499476] dpaa2_mac dpmac.6: Adding to iommu group 0 [ 6.504616] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.511007] dpaa2_mac dpmac.5: Adding to iommu group 0 [ 6.516147] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.522535] dpaa2_mac dpmac.4: Adding to iommu group 0 [ 6.527682] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.534068] dpaa2_mac dpmac.3: Adding to iommu group 0 [ 6.539215] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.545598] dpaa2_mac dpmac.2: Adding to iommu group 0 [ 6.550746] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.557132] dpaa2_caam dpseci.0: Adding to iommu group 0 [ 6.562475] fsl_mc_dprc dprc.1: No more resources of type dpmcp left [ 6.571775] fsl_mc_allocator dpmcp.35: Adding to iommu group 0 [ 6.578742] fsl_mc_allocator dpmcp.34: Adding to iommu group 0 [ 6.585669] fsl_mc_allocator dpmcp.33: Adding to iommu group 0 [ 6.592651] fsl_mc_allocator dpmcp.32: Adding to iommu group 0 [ 6.599584] fsl_mc_allocator dpmcp.31: Adding to iommu group 0 [ 6.606570] fsl_mc_allocator dpmcp.30: Adding to iommu group 0 [ 6.613491] fsl_mc_allocator dpmcp.29: Adding to iommu group 0 [ 6.620418] fsl_mc_allocator dpmcp.28: Adding to iommu group 0 [ 6.627395] fsl_mc_allocator dpmcp.27: Adding to iommu group 0 [ 6.634318] fsl_mc_allocator dpmcp.26: Adding to iommu group 0 [ 6.641304] fsl_mc_allocator dpmcp.25: Adding to iommu group 0 [ 6.648229] fsl_mc_allocator dpmcp.24: Adding to iommu group 0 [ 6.655163] fsl_mc_allocator dpmcp.23: Adding to iommu group 0 [ 6.662121] fsl_mc_allocator dpmcp.22: Adding to iommu group 0 [ 6.669045] fsl_mc_allocator dpmcp.21: Adding to iommu group 0 [ 6.676034] fsl_mc_allocator dpmcp.20: Adding to iommu group 0 [ 6.682970] fsl_mc_allocator dpmcp.19: Adding to iommu group 0 [ 6.689899] fsl_mc_allocator dpmcp.18: Adding to iommu group 0 [ 6.696852] fsl_mc_allocator dpmcp.17: Adding to iommu group 0 [ 6.703779] fsl_mc_allocator dpmcp.16: Adding to iommu group 0 [ 6.710778] fsl_mc_allocator dpmcp.15: Adding to iommu group 0 [ 6.717706] fsl_mc_allocator dpmcp.14: Adding to iommu group 0 [ 6.724699] fsl_mc_allocator dpmcp.13: Adding to iommu group 0 [ 6.731645] fsl_mc_allocator dpmcp.12: Adding to iommu group 0 [ 6.738641] fsl_mc_allocator dpmcp.11: Adding to iommu group 0 [ 6.745572] fsl_mc_allocator dpmcp.10: Adding to iommu group 0 [ 6.752558] fsl_mc_allocator dpmcp.9: Adding to iommu group 0 [ 6.759452] fsl_mc_allocator dpmcp.8: Adding to iommu group 0 [ 6.766323] fsl_mc_allocator dpmcp.7: Adding to iommu group 0 [ 6.773206] fsl_mc_allocator dpmcp.6: Adding to iommu group 0 [ 6.780085] fsl_mc_allocator dpmcp.5: Adding to iommu group 0 [ 6.786976] fsl_mc_allocator dpmcp.4: Adding to iommu group 0 [ 6.793848] fsl_mc_allocator dpmcp.3: Adding to iommu group 0 [ 6.800730] fsl_mc_allocator dpmcp.2: Adding to iommu group 0 [ 6.807620] fsl_mc_allocator dpmcp.1: Adding to iommu group 0 [ 6.813462] fsl_dpaa2_ptp dprtc.0: Adding to iommu group 0 [ 6.821212] ptp_qoriq: device tree node missing required elements, try automatic configuration [ 6.830011] pps pps0: new PPS source ptp0 [ 6.837160] fsl_mc_dpio dpio.15: Adding to iommu group 0 [ 6.846112] fsl_mc_dpio dpio.15: probed [ 6.853580] fsl_mc_dpio dpio.14: Adding to iommu group 0 [ 6.862482] fsl_mc_dpio dpio.14: probed [ 6.869885] fsl_mc_dpio dpio.13: Adding to iommu group 0 [ 6.878833] fsl_mc_dpio dpio.13: probed [ 6.886267] fsl_mc_dpio dpio.12: Adding to iommu group 0 [ 6.895214] fsl_mc_dpio dpio.12: probed [ 6.902659] fsl_mc_dpio dpio.11: Adding to iommu group 0 [ 6.911609] fsl_mc_dpio dpio.11: probed [ 6.919084] fsl_mc_dpio dpio.10: Adding to iommu group 0 [ 6.927984] fsl_mc_dpio dpio.10: probed [ 6.935424] fsl_mc_dpio dpio.9: Adding to iommu group 0 [ 6.944221] fsl_mc_dpio dpio.9: probed [ 6.951589] fsl_mc_dpio dpio.8: Adding to iommu group 0 [ 6.960431] fsl_mc_dpio dpio.8: probed [ 6.967852] fsl_mc_dpio dpio.7: Adding to iommu group 0 [ 6.976670] fsl_mc_dpio dpio.7: probed [ 6.984039] fsl_mc_dpio dpio.6: Adding to iommu group 0 [ 6.992871] fsl_mc_dpio dpio.6: probed [ 7.000309] fsl_mc_dpio dpio.5: Adding to iommu group 0 [ 7.009123] fsl_mc_dpio dpio.5: probed [ 7.016489] fsl_mc_dpio dpio.4: Adding to iommu group 0 [ 7.025330] fsl_mc_dpio dpio.4: probed [ 7.032755] fsl_mc_dpio dpio.3: Adding to iommu group 0 [ 7.041568] fsl_mc_dpio dpio.3: probed [ 7.048941] fsl_mc_dpio dpio.2: Adding to iommu group 0 [ 7.057789] fsl_mc_dpio dpio.2: probed [ 7.065222] fsl_mc_dpio dpio.1: Adding to iommu group 0 [ 7.074039] fsl_mc_dpio dpio.1: probed [ 7.081407] fsl_mc_dpio dpio.0: Adding to iommu group 0 [ 7.090250] fsl_mc_dpio dpio.0: probed [ 7.094604] fsl_mc_allocator dpcon.31: Adding to iommu group 0 [ 7.100545] fsl_mc_allocator dpcon.30: Adding to iommu group 0 [ 7.106481] fsl_mc_allocator dpcon.29: Adding to iommu group 0 [ 7.112417] fsl_mc_allocator dpcon.28: Adding to iommu group 0 [ 7.118349] fsl_mc_allocator dpcon.27: Adding to iommu group 0 [ 7.124285] fsl_mc_allocator dpcon.26: Adding to iommu group 0 [ 7.130223] fsl_mc_allocator dpcon.25: Adding to iommu group 0 [ 7.136157] fsl_mc_allocator dpcon.24: Adding to iommu group 0 [ 7.142092] fsl_mc_allocator dpcon.23: Adding to iommu group 0 [ 7.148029] fsl_mc_allocator dpcon.22: Adding to iommu group 0 [ 7.153967] fsl_mc_allocator dpcon.21: Adding to iommu group 0 [ 7.159909] fsl_mc_allocator dpcon.20: Adding to iommu group 0 [ 7.165843] fsl_mc_allocator dpcon.19: Adding to iommu group 0 [ 7.171781] fsl_mc_allocator dpcon.18: Adding to iommu group 0 [ 7.177719] fsl_mc_allocator dpcon.17: Adding to iommu group 0 [ 7.183654] fsl_mc_allocator dpcon.16: Adding to iommu group 0 [ 7.189595] fsl_mc_allocator dpcon.15: Adding to iommu group 0 [ 7.195536] fsl_mc_allocator dpcon.14: Adding to iommu group 0 [ 7.201474] fsl_mc_allocator dpcon.13: Adding to iommu group 0 [ 7.207415] fsl_mc_allocator dpcon.12: Adding to iommu group 0 [ 7.213354] fsl_mc_allocator dpcon.11: Adding to iommu group 0 [ 7.219293] fsl_mc_allocator dpcon.10: Adding to iommu group 0 [ 7.225233] fsl_mc_allocator dpcon.9: Adding to iommu group 0 [ 7.231085] fsl_mc_allocator dpcon.8: Adding to iommu group 0 [ 7.236938] fsl_mc_allocator dpcon.7: Adding to iommu group 0 [ 7.242795] fsl_mc_allocator dpcon.6: Adding to iommu group 0 [ 7.248650] fsl_mc_allocator dpcon.5: Adding to iommu group 0 [ 7.254507] fsl_mc_allocator dpcon.4: Adding to iommu group 0 [ 7.260361] fsl_mc_allocator dpcon.3: Adding to iommu group 0 [ 7.266215] fsl_mc_allocator dpcon.2: Adding to iommu group 0 [ 7.272072] fsl_mc_allocator dpcon.1: Adding to iommu group 0 [ 7.277927] fsl_mc_allocator dpcon.0: Adding to iommu group 0 [ 7.286983] fsl_mc_dprc dprc.1: DPRC device bound to driver [ 7.440549] fsl_dpaa2_eth dpni.1: Probed interface eth0 [ 7.593633] fsl_dpaa2_eth dpni.0: Probed interface eth1 [ 7.603310] dpaa2_mac dpmac.18: Connected to rgmii-id PHY. [ 7.613297] dpaa2_mac dpmac.17: Connected to rgmii-id PHY. [ 7.622647] dpaa2_mac dpmac.6: Registered fixed PHY. [ 7.631434] dpaa2_mac dpmac.5: Registered fixed PHY. [ 7.667757] dpaa2_mac dpmac.4: Connected to usxgmii PHY. [ 7.703688] dpaa2_mac dpmac.3: Connected to usxgmii PHY. [ 7.712739] dpaa2_mac dpmac.2: Registered fixed PHY. [ 7.719136] dpaa2_caam dpseci.0: dpseci v5.3 [ 7.746639] fsl_mc_dprc dprc.1 (unnamed net_device) (uninitialized): netif_napi_add() called with weight 512 [ 7.773719] dpaa2_caam dpseci.0: algorithms registered in /proc/crypto [ 7.781161] dpaa2_caam dpseci.0: hash algorithms registered in /proc/crypto [ 7.790007] rtc-pcf2127-i2c 1-0051: setting system clock to 2020-09-20T07:40:27 UTC (1600587627) [ 7.798957] ALSA device list: [ 7.801913] No soundcards found. [ 7.810201] random: fast init done [ 7.910001] EXT4-fs (sda4): recovery complete [ 7.914475] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) [ 7.922148] VFS: Mounted root (ext4 filesystem) on device 8:4. [ 7.929328] devtmpfs: mounted [ 7.933994] Freeing unused kernel memory: 5888K [ 7.938637] Run /sbin/init as init process [ 8.032488] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 8.054418] systemd[1]: Detected architecture arm64. Welcome to NXP LSDK 2004 main! [ 8.090932] systemd[1]: Set hostname to . [ 8.187250] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 8.204316] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 8.253628] systemd[1]: Configuration file /lib/systemd/system/weston.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 8.302753] systemd[1]: Configuration file /lib/systemd/system/fmc.service is marked executable. Please remove executable permission bits. Proceeding anyway. [ 8.339091] random: systemd: uninitialized urandom read (16 bytes read) [ 8.354738] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 8.370661] random: systemd: uninitialized urandom read (16 bytes read) [ 8.378636] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 8.394653] random: systemd: uninitialized urandom read (16 bytes read) [ 8.405411] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ OK ] Created slice System Slice. [ OK ] Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on udev Control Socket. Mounting Huge Pages File System... Starting Create Static Device Nodes in /dev... [ OK ] Listening on udev Kernel Socket. Mounting POSIX Message Queue File System... [ OK ] Listening on Journal Audit Socket. [ OK ] Reached target Slices. [ OK ] Listening on Syslog Socket. [ OK ] Listening on fsck to fsckd communication Socket. Starting Remount Root and Kernel File Systems... Starting udev Coldplug all Devices... [ 8.606150] EXT4-fs (sda4): re-mounted. Opts: errors=remount-ro [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Reached target Swap. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Local Encrypted Volumes. Mounting Kernel Debug File System... Starting Journal Service... Starting Set the console keyboard layout... [ OK ] Reached target Paths. [ OK ] Mounted Huge Pages File System. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Mounted Kernel Debug File System. Starting Load/Save Random Seed... Starting udev Kernel Device Manager... [ OK ] Started Load/Save Random Seed. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Set the console keyboard layout. [ OK ] Reached target Local File Systems (Pre). Mounting Boot Partition... [ OK ] Reached target Local File Systems. Starting Set console font and keymap... Starting QEMU KVM preparation - module, ksm, hugepages... [ OK ] Started Set console font and keymap. [ OK ] Started QEMU KVM preparation - module, ksm, hugepages. [ OK ] Started Journal Service. Starting Flush Journal to Persistent Storage... [ 9.327057] systemd-journald[649]: Received request to flush runtime journal from PID 1 [ 9.352945] systemd-journald[649]: File /var/log/journal/88792e6c2f004b9cbb23929dea8bf36c/system.journal corrupted or uncleanly shut down, renaming and replacing. [ 9.400044] EXT4-fs (sda2): recovery complete [ 9.404611] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ OK ] Mounted Boot Partition. Starting Load Kernel Modules... [ 9.473275] pfe: module is from the staging directory, the quality is unknown, you have been warned. [ OK ] Started Load Kernel Modules. Mounting Kernel Configuration File System... Mounting FUSE Control File System... [ 9.529814] switch cluster 0 cpu-freq governor to schedutil Starting Apply Kernel Variables... [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Mounted Kernel Configuration File System. [ OK ] Mounted FUSE Control File System. [ OK ] Started Apply Kernel Variables. Starting Raise network interfaces... Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting Network Name Resolution... Starting Network Time Synchronization... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started udev Coldplug all Devices. [ OK ] Started Network Time Synchronization. [ OK ] Started Network Name Resolution. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Docker Socket for the API. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Message of the Day. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on Docker Socket for the API. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. Starting Resets System Activity Data Collector... [ OK ] Started Set the CPU Frequency Scaling governor. Starting LSB: Execute the kexec -e command to reboot system... Starting Login Service... Starting Dispatcher daemon for systemd-networkd... [ OK ] Started D-Bus System Message Bus. [ OK ] Started Regular background program processing daemon. Starting System Logging Service... [ OK ] Started Resets System Activity Data Collector. [ OK ] Started System Logging Service. [ OK ] Started Login Service. [ OK ] Started LSB: Execute the kexec -e command to reboot system. Starting LSB: Load kernel image with kexec... [ OK ] Started LSB: Load kernel image with kexec. [ OK ] Started Dispatcher daemon for systemd-networkd. [ OK ] Found device /dev/ttyAMA0. [ OK ] Found device /sys/subsystem/net/devices/eth1. [ OK ] Started ifup for eth1. [ OK ] Started Raise network interfaces. [ OK ] Reached target Network. Starting Permit User Sessions... [ OK ] Started Unattended Upgrades Shutdown. Starting containerd container runtime... Starting OpenBSD Secure Shell server... Starting NXP Frame Manager Configuration tool... Starting vsftpd FTP server... [ OK ] Reached target Network is Online. Starting Message of the Day... [ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf. Starting LSB: HPA's tftp server... Starting Daily apt download activities... [ OK ] Started Permit User Sessions. [ OK ] Started containerd container runtime. [ OK ] Started NXP Frame Manager Configuration tool. [ OK ] Started vsftpd FTP server. [FAILED] Failed to start Message of the Day. See 'systemctl status motd-news.service' for details. [ OK ] Started OpenBSD Secure Shell server. Starting Docker Application Container Engine... [ OK ] Started Serial Getty on ttyAMA0. Starting Set console scheme... Starting Weston Wayland Compositor (on tty7)... [ OK ] Started Set console scheme. [ OK ] Started Weston Wayland Compositor (on tty7). [ OK ] Created slice system-getty.slice. [ OK ] Started Getty on tty1. [ OK ] Reached target Login Prompts. [ OK ] Started LSB: HPA's tftp server. [ OK ] Created slice User Slice of root. Starting User Manager for UID 0... [ OK ] Started Session 1 of user root. [ OK ] Started User Manager for UID 0. Stopping User Manager for UID 0... [ OK ] Stopped User Manager for UID 0. [ OK ] Removed slice User Slice of root. NXP LSDK 2004 main localhost login: root Password: Last login: Sun Sep 20 07:40:32 UTC 2020 on tty7 Welcome to NXP LSDK 2004 main (GNU/Linux 5.4.3 aarch64) * Support: https://www.nxp.com/lsdk * Documentation: https://lsdk.github.io/document * Licensing: https://lsdk.github.io/eula