=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2023.12.05 15:03:56 =~=~=~=~=~=~=~=~=~=~=~= in ddr_init file befoer dram_init 1600000000 in ddr.c file dram_init in ddr.c file before board_static_ddr ddr bus width 0x2, sdram_cfg[0] 0x450c0000 ,temp 0x1 NOTICE: Build-in self test passed NOTICE: 1 GB DDR4, 32-bit, CL=11, ECC off NOTICE: BL2: v2.6(release):lf-5.15.71-2.2.0-0-g3c1583ba0-dirty NOTICE: BL2: Built : 11:00:38, Nov 21 2022 NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.6(release):lf-5.15.71-2.2.0-0-g3c1583ba0-dirty NOTICE: BL31: Built : 11:00:38, Nov 21 2022 NOTICE: Welcome to ls1043ardb BL31 Phase U-Boot 2022.04+fsl+g181859317b (Nov 15 2022 - 06:28:05 +0000) U-Boot code: 82000000 -> 8209F758 BSS: -> 820AD1A8 SoC: LS1043AE Rev1.1 (0x87920211) Clock Configuration: CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz CPU3(A53):1600 MHz Bus: 400 MHz DDR: 1600 MT/s FMAN: 500 MHz Reset Configuration Word (RCW): 00000000: 08100010 0a000000 00000000 00000000 00000010: 00000002 00c04012 e0025000 c1002000 00000020: 00000000 00000000 00000000 010b8800 00000030: 00000000 00001105 00000096 00000001 Model: LS1043A RDB Board get_boot_src: porsr1 0x12ffffff __get_boot_src: rcw_src 0x25 __get_boot_src: src 0x1 Board: LS1043ARDB, boot from Nor DRAM: Monitor len: 000AD1A8 Ram size: 3BE00000 Ram top Ram top: B7C00000 ethernet-phy@1 node not found in the dts Reserving 692k for U-Boot at: b7b42000 Reserving 1040k for malloc() at: b7a3e000 Reserving 152 Bytes for Board Info at: b7a3df60 Reserving 488 Bytes for Global Data at: b7a3dd70 Reserving 17920 Bytes for FDT at: b7a39770 dram_size 3be00000 bank[0]: start 80000000, size 3be00000 Bank #0: 80000000 958 MiB Bank #1: 0 0 Bytes DRAM: 958 MiB (DDR4, 32-bit, CL=11, ECC off) New Stack Pointer is: b7a39760 Relocation Offset is: 35b42000 Relocating to b7b42000, new gd at b7a3dd70, sp at b7a39760 Pre-reloc malloc() used 0x288 bytes (0 KB) - found match at 'simple_bus': 'simple-bus' matches 'simple-bus' - found match at 'simple_bus': 'simple-bus' matches 'simple-bus' - found match at 'caam_jr': 'fsl,sec-v4.0' matches 'fsl,sec-v4.0' - found match at 'fman': 'fsl,fman' matches 'fsl,fman' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'eth_fman': 'fsl,fman-memac' matches 'fsl,fman-memac' fm_eth_bind - binding fm1-mac3 - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'eth_fman': 'fsl,fman-memac' matches 'fsl,fman-memac' fm_eth_bind - binding fm1-mac4 - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' - found match at 'fman_mdio': 'fsl,fman-memac-mdio' matches 'fsl,fman-memac-mdio' get_boot_src: porsr1 0x12ffffff __get_boot_src: rcw_src 0x25 __get_boot_src: src 0x1 get_boot_src: porsr1 0x12ffffff __get_boot_src: rcw_src 0x25 __get_boot_src: src 0x1 Firmware 'Microcode version 0.0.1 for LS1021a r1.0' for 1021 V1.0 QE: uploading microcode 'Microcode for LS1021a r1.0' version 0.0.1 Now running in RAM - U-Boot at: b7b42000 Core: 16 devices, 5 uclasses, devicetree: separate Using SERDES1 Protocol: 0 (0x0) SERDES1[PRTCL] = 0x0 is not valid Flash: flash detect cfi is= cmd 51(Q) addr 0000000060000010 is= 0 51 is= cmd 51(Q) addr 0000000060000010 is= 0 51 is= cmd 51(Q) addr 0000000060000020 is= 2 51 is= cmd 51(Q) addr 0000000060000020 is= 2 51 is= cmd 51(Q) addr 0000000060000020 is= 0051 5151 is= cmd 51(Q) addr 0000000060000020 is= 0051 5151 is= cmd 51(Q) addr 0000000060000040 is= 0000 5151 is= cmd 51(Q) addr 0000000060000040 is= 0000 5151 is= cmd 51(Q) addr 0000000060000020 is= 0051 0051 is= cmd 52(R) addr 0000000060000022 is= 0052 0052 is= cmd 59(Y) addr 0000000060000024 is= 0059 0059 device interface is 1 found port 2 chip 2 chip_lsb 0 port 16 bits chip 16 bits 00 : 51 52 59 02 00 40 00 00 00 00 00 27 36 85 95 05 QRY..@.....'6... 10 : 09 08 12 03 02 03 03 1c 01 00 0a 00 01 ff 07 00 ................ 20 : 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ info->ext_addr = 0x40, cfi_version = 0x3135 feature = 0x8f manufacturer is 2 manufacturer id is 0x89 device id is 0x227e device id2 is 0x4801 cfi version is 0x3135 size_ratio 1 port 16 bits chip 16 bits found 1 erase regions erase region 0: 0x020007ff erase_region_count = 2048 erase_region_size = 131072 flash_protect ON: from 0x60500000 to 0x6051FFFF protect on 40 256 MiB MMC: 0 - not found get_boot_src: porsr1 0x12ffffff __get_boot_src: rcw_src 0x25 __get_boot_src: src 0x1 Loading Environment from Flash... 1 - 0 'fm1-mac3' - 1 'fm1-mac4' - found 2 - 0 'fm1-mac3' - 1 'fm1-mac4' - not found 0 - 0 'fm1-mac3' - found OK In: serial Out: serial Err: serial SEC0: RNG instantiated Assign to qe-hdlc clk, rcwpmuxcr0=6611 Net: ADIN1300 PHY registerd get_boot_src: porsr1 0x12ffffff __get_boot_src: rcw_src 0x25 __get_boot_src: src 0x1 Fman1: Uploading microcode version 106.4.18 fm_eth_probe enter for dev 00000000b7a3e830 fm_eth 00000000b7a3f580 - fm1-mac3 MAC system interface mode rgmii-id init_memac: @ 0000000001ae4000, mdio @ 0000000000000000 fm_eth_rx_port_parameter_init: rx_buf_pool = 00000000b7a47dc0 Looking for mdio@fc000 Looking for mdio@fc000 - checking mdio@fc000 - result for mdio@fc000: mdio@fc000 (ret=0) - result for mdio@fc000: mdio@fc000 (ret=0) fm_mdio_probe priv 00000000b7a3f830 @ regs 0000000001afc000, pdata 00000000b7a3f850 ADIN1300 PHY adin1300_probe memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 0, val 0x8000) fm1-mac3 connected to ADIN1300 adin_ext_write: adin@0x8 0xff1f=0x18 memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 16, val 0xff1f) memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 17, val 0x18) adin_get_phy_mode_override: adi,phy-mode-override = 'rgmii-id' memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 16, val 0xff23) adin_ext_read: adin@0x8 0xff23=0xe07 adin_get_reg_value: adi,rx-internal-delay-ps = '2400' adin_get_reg_value: adi,tx-internal-delay-ps = '2400' adin ADIN1300_GE_RGMII_CFG 0xfff adin_ext_write: adin@0x8 0xff23=0xfff memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 16, val 0xff23) memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 17, val 0xfff) memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 16, val 0xff26) adin_ext_read: adin@0x8 0xff26=0xc86 ADIN1300_PHY_BASIC_CFG_REG 0xc86 ADIN1300_PHY_CNTL_REG 0x2 memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 4, val 0x1e1) memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 9, val 0x300) memac_mdio_write(regs 0000000001afc000, port 8, dev -1, reg 0, val 0x1240) fm_eth_probe enter for dev 00000000b7a3e9e0 fm_eth 00000000b7a3fa40 - fm1-mac4 MAC system interface mode rgmii-id init_memac: @ 0000000001ae6000, mdio @ 0000000000000000 fm_eth_rx_port_parameter_init: rx_buf_pool = 00000000b7a4bdd0 Looking for mdio@fc000 Looking for mdio@fc000 - checking mdio@fc000 - result for mdio@fc000: mdio@fc000 (ret=0) - result for mdio@fc000: mdio@fc000 (ret=0) ADIN1300 PHY adin1300_probe memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 0, val 0x8000) fm1-mac4 connected to ADIN1300 adin_ext_write: adin@0xc 0xff1f=0x18 memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 16, val 0xff1f) memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 17, val 0x18) adin_get_phy_mode_override: adi,phy-mode-override = 'rgmii-id' memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 16, val 0xff23) adin_ext_read: adin@0xc 0xff23=0xe07 adin_get_reg_value: adi,rx-internal-delay-ps = '2400' adin_get_reg_value: adi,tx-internal-delay-ps = '2400' adin ADIN1300_GE_RGMII_CFG 0xfff adin_ext_write: adin@0xc 0xff23=0xfff memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 16, val 0xff23) memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 17, val 0xfff) memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 16, val 0xff26) adin_ext_read: adin@0xc 0xff26=0xc86 ADIN1300_PHY_BASIC_CFG_REG 0xc86 ADIN1300_PHY_CNTL_REG 0x2 memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 4, val 0x1e1) memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 9, val 0x300) memac_mdio_write(regs 0000000001afc000, port 12, dev -1, reg 0, val 0x1240) eth0: fm1-mac3, eth1: fm1-mac4 Hit any key to stop autoboot: 10  9  0 => tftp 0x81000000 uImage_2_12 0 - 0 'fm1-mac3' - found Trying fm1-mac4 fm1-mac4 Waiting for PHY auto negotiation to complete......... TIMEOUT ! fm1-mac4: Could not initialize FAIL Trying fm1-mac3 memac_set_interface_mode, if_mode = 1006 memac_set_interface_mode, if_status = b000 MAC IF mode 8, speed 100, link 1 Using fm1-mac3 device TFTP from server 192.168.20.54; our IP address is 192.168.20.110 Filename 'uImage_2_12'. Load address: 0x81000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.9 MiB/s done dev=Net, devnr=, path=uImage_2_12, buffer=0000000081000000, size=16e0240 Wrong FIT format: not a flattened device tree (err=-9) - not remembering image Bytes transferred = 23986752 (16e0240 hex) => tftp 0xA0000000 test_serial_i2c_LB_TX Trying fm1-mac3 memac_set_interface_mode, if_mode = 1006 memac_set_interface_mode, if_status = b000 MAC IF mode 8, speed 100, link 1 Using fm1-mac3 device TFTP from server 192.168.20.54; our IP address is 192.168.20.110 Filename 'test_serial_i2c_LB_TX'. Load address: 0xa0000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.2 MiB/s done dev=Net, devnr=, path=test_serial_i2c_LB_TX, buffer=00000000a0000000, size=29fd4e6 Wrong FIT format: not a flattened device tree (err=-9) - not remembering image Bytes transferred = 44029158 (29fd4e6 hex) => tftp 0x92000000 fsl-ls1043a-rdb-sdk_2_12.dtb Trying fm1-mac3 memac_set_interface_mode, if_mode = 1006 memac_set_interface_mode, if_status = b000 MAC IF mode 8, speed 100, link 1 Using fm1-mac3 device TFTP from server 192.168.20.54; our IP address is 192.168.20.110 Filename 'fsl-ls1043a-rdb-sdk_2_12.dtb'. Load address: 0x92000000 Loading: *## 2.9 KiB/s done dev=Net, devnr=, path=fsl-ls1043a-rdb-sdk_2_12.dtb, buffer=0000000092000000, size=4aff Wrong FIT format: no description - not remembering image Bytes transferred = 19199 (4aff hex) => bootm 0x81000000 0xA0000000 0x92000000 ## Booting kernel from Legacy Image at 81000000 ... Image Name: Kernel Image Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 23986688 Bytes = 22.9 MiB Load Address: 84080000 Entry Point: 84080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at a0000000 ... Image Name: Ramdisk Image Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 44029094 Bytes = 42 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Wrong FIT format: no description ## Flattened Device Tree blob at 92000000 Booting using the fdt blob at 0x92000000 Loading Kernel Image Using Device Tree in place at 0000000092000000, end 0000000092017afe WARNING: Missing crypto node WARNING failed to get smmu node: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/msi-controller1@1571000: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/msi-controller2@1572000: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/msi-controller3@1573000: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/pcie@3400000: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/pcie@3500000: FDT_ERR_NOTFOUND WARNING: fdt_path_offset can't find path /soc/pcie@3600000: FDT_ERR_NOTFOUND ethernet-phy@1 node not found in the dts WARNING failed to get smmu node: FDT_ERR_NOTFOUND Starting kernel ... crypto@1700000: When removing: flags=4600, drv->flags=0, err=-129 mdio@fc000: When removing: flags=4600, drv->flags=0, err=-129 fm1-mac3: When removing: flags=4600, drv->flags=20, err=-129 fm1-mac4: When removing: flags=4600, drv->flags=20, err=-129 fman@1a00000: When removing: flags=4600, drv->flags=20, err=-129 soc: When removing: flags=4600, drv->flags=4, err=-129 root_driver: When removing: flags=4600, drv->flags=0, err=-129 crypto@1700000: When removing: flags=600, drv->flags=0, err=-129 mdio@fc000: When removing: flags=600, drv->flags=0, err=-129 fm1-mac3: When removing: flags=600, drv->flags=20, err=-129 fm1-mac4: When removing: flags=600, drv->flags=20, err=-129 fman@1a00000: When removing: flags=600, drv->flags=20, err=-129 soc: When removing: flags=600, drv->flags=4, err=-129 root_driver: When removing: flags=600, drv->flags=0, err=-129 [ T0] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ T0] Linux version 5.15.71+g95448dd0dc9b (oe-user@oe-host) (aarch64-fsl-linux-gcc (GCC) 11.2.0, GNU ld (GNU Binutils) 2.38.20220313) #1 SMP PREEMPT Wed Feb 8 03:38:28 UTC 2023 [ T0] Machine model: LS1043A RDB Board [ T0] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '') [ T0] printk: bootconsole [uart8250] enabled [ T0] efi: UEFI not found. [ T0] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ T0] OF: reserved mem: initialized node qman-fqd, compatible id fsl,qman-fqd [ T0] OF: reserved mem: initialized node qman-pfdr, compatible id fsl,qman-pfdr [ T0] OF: reserved mem: initialized node bman-fbpr, compatible id fsl,bman-fbpr [ T0] NUMA: Initialized distance table, cnt=16 [ T0] NUMA: No NUMA configuration found [ T0] NUMA: Initialized distance table, cnt=16 [ T0] NUMA: Faking a node at [mem 0x0000000080000000-0x00000000bbdfffff] [ T0] NUMA: NODE_DATA [mem 0xbbc19c00-0xbbc1bfff] [ T0] NUMA: Node to cpumask map for 1 nodes [ T0] Zone ranges: [ T0] DMA [mem 0x0000000080000000-0x00000000bbdfffff] [ T0] DMA32 empty [ T0] Normal empty [ T0] Movable zone start for each node [ T0] Early memory node ranges [ T0] node 0: [mem 0x0000000080000000-0x00000000b7ffffff] [ T0] node 0: [mem 0x00000000b8000000-0x00000000baffffff] [ T0] node 0: [mem 0x00000000bb000000-0x00000000bb7fffff] [ T0] node 0: [mem 0x00000000bb800000-0x00000000bbbfffff] [ T0] node 0: [mem 0x00000000bbc00000-0x00000000bbdfffff] [ T0] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bbdfffff] [ T0] On node 0, zone DMA: 16896 pages in unavailable ranges [ T0] cma: Reserved 32 MiB at 0x00000000b5000000 [ T0] psci: probing for conduit method from DT. [ T0] psci: PSCIv1.1 detected in firmware. [ T0] psci: Using standard PSCI v0.2 function IDs [ T0] psci: MIGRATE_INFO_TYPE not supported. [ T0] psci: SMC Calling Convention v1.2 [ T0] percpu: Embedded 21 pages/cpu s45976 r8192 d31848 u86016 [ T0] pcpu-alloc: s45976 r8192 d31848 u86016 alloc=21*4096 [ T0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ T0] Detected VIPT I-cache on CPU0 [ T0] CPU features: kernel page table isolation forced ON by KASLR [ T0] CPU features: detected: Kernel page table isolation (KPTI) [ T0] CPU features: detected: ARM erratum 845719 [ T0] Built 1 zonelists, mobility grouping on. Total pages: 241416 [ T0] Policy zone: DMA [ T0] Kernel command line: console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500; [ T0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ T0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ T0] mem auto-init: stack:off, heap alloc:off, heap free:off [ T0] Memory: 807272K/980992K available (14656K kernel code, 1216K rwdata, 5148K rodata, 2304K init, 950K bss, 140952K reserved, 32768K cma-reserved) [ T0] rcu: Preemptible hierarchical RCU implementation. [ T0] rcu: RCU event tracing is enabled. [ T0] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ T0] Trampoline variant of Tasks RCU enabled. [ T0] Tracing variant of Tasks RCU enabled. [ T0] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ T0] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ T0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ T0] GIC: Adjusting CPU interface base to 0x000000000142f000 [ T0] Root IRQ handler: gic_handle_irq [ T0] GIC: Using split EOI/Deactivate mode [ T0] arch_timer: Enabling global workaround for Freescale erratum a005858 [ T0] arch_timer: CPU0: Trapping CNTVCT access [ T0] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ T0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ T0] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ T0] Console: colour dummy device 80x25 [ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ T0] pid_max: default: 32768 minimum: 301 [ T0] LSM: Security Framework initializing [ T0] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ T0] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ T1] rcu: Hierarchical SRCU implementation. [ T1] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ T1] EFI services will not be available. [ T1] smp: Bringing up secondary CPUs ... [ T0] Detected VIPT I-cache on CPU1 [ T0] arch_timer: CPU1: Trapping CNTVCT access [ T0] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ T0] Detected VIPT I-cache on CPU2 [ T0] arch_timer: CPU2: Trapping CNTVCT access [ T0] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ T0] Detected VIPT I-cache on CPU3 [ T0] arch_timer: CPU3: Trapping CNTVCT access [ T0] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ T1] smp: Brought up 1 node, 4 CPUs [ T1] SMP: Total of 4 processors activated. [ T1] CPU features: detected: 32-bit EL0 Support [ T1] CPU features: detected: 32-bit EL1 Support [ T1] CPU features: detected: CRC32 instructions [ T1] CPU: All CPU(s) started at EL2 [ T14] alternatives: patching kernel code [ T1] devtmpfs: initialized [ T1] device: 'platform': device_add [ T1] PM: Adding info for No Bus:platform [ T1] bus: 'platform': registered [ T1] bus: 'cpu': registered [ T1] device: 'cpu': device_add [ T1] PM: Adding info for No Bus:cpu [ T1] bus: 'container': registered [ T1] device: 'container': device_add [ T1] PM: Adding info for No Bus:container [ T1] KASLR enabled [ T1] bus: 'workqueue': registered [ T1] device: 'workqueue': device_add [ T1] PM: Adding info for No Bus:workqueue [ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ T1] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ T1] pinctrl core: initialized pinctrl subsystem [ T1] bus: 'gpio': registered [ T1] bus: 'gpio': add driver gpio_stub_drv [ T1] bus: 'platform': add driver fsl-guts [ T1] bus: 'virtio': registered [ T1] device class 'regulator': registering [ T1] Registering platform device 'reg-dummy'. Parent at platform [ T1] device: 'reg-dummy': device_add [ T1] bus: 'platform': add device reg-dummy [ T1] PM: Adding info for platform:reg-dummy [ T1] bus: 'platform': add driver reg-dummy [ T1] bus: 'platform': __driver_probe_device: matched device reg-dummy with driver reg-dummy [ T1] bus: 'platform': really_probe: probing driver reg-dummy with device reg-dummy [ T1] reg-dummy reg-dummy: no default pinctrl state [ T1] device: 'regulator.0': device_add [ T1] PM: Adding info for No Bus:regulator.0 [ T1] driver: 'reg-dummy': driver_bound: bound to device 'reg-dummy' [ T1] devices_kset: Moving reg-dummy to end of list [ T1] PM: Moving platform:reg-dummy to end of list [ T1] devices_kset: Moving regulator.0 to end of list [ T1] PM: Moving No Bus:regulator.0 to end of list [ T1] bus: 'platform': really_probe: bound device reg-dummy to driver reg-dummy [ T1] bus: 'genpd': registered [ T1] bus: 'soc': registered [ T1] DMI not present or invalid. [ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ T1] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ T1] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ T1] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ T1] audit: initializing netlink subsys (disabled) [ T1] device class 'bdi': registering [ T37] audit: type=2000 audit(0.240:1): state=initialized audit_enabled=0 res=1 [ T1] bus: 'fsl-mc': registered [ T1] bus: 'platform': add driver fsl_mc_bus [ T1] bus: 'fsl-mc': add driver fsl_mc_dprc [ T1] bus: 'fsl-mc': add driver fsl_mc_allocator [ T1] bus: 'amba': registered [ T1] device class 'tty': registering [ T1] device class 'vtconsole': registering [ T1] device: 'vtcon0': device_add [ T1] PM: Adding info for No Bus:vtcon0 [ T1] bus: 'serial': registered [ T1] device class 'iommu': registering [ T1] device class 'devlink': registering [ T1] device class 'wakeup': registering [ T1] bus: 'node': registered [ T1] device: 'node': device_add [ T1] PM: Adding info for No Bus:node [ T1] bus: 'platform': add driver sram [ T1] bus: 'platform': add driver syscon [ T1] bus: 'spi': registered [ T1] device class 'spi_master': registering [ T1] bus: 'spmi': registered [ T1] bus: 'i2c': registered [ T1] bus: 'i2c': add driver dummy [ T1] i2c-core: driver [dummy] registered [ T1] thermal_sys: Registered thermal governor 'step_wise' [ T1] thermal_sys: Registered thermal governor 'power_allocator' [ T1] device class 'thermal': registering [ T1] cpuidle: using governor menu [ T1] bus: 'rpmsg': registered [ T1] bus: 'rpmsg': add driver rpmsg_ns [ T1] Bman ver:0a02,02,01 [ T1] qman-fqd addr 0x00000000bb800000 size 0x400000 [ T1] qman-pfdr addr 0x00000000b8000000 size 0x2000000 [ T1] Qman ver:0a01,03,02,00 [ T1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ T1] ASID allocator initialised with 32768 entries [ T1] bus: 'platform': add driver gpio-mpc8xxx [ T1] device class 'dma': registering [ T1] bus: 'platform': add driver gpio-reset [ T1] Serial: AMBA PL011 UART driver [ T1] bus: 'platform': add driver sbsa-uart [ T1] bus: 'amba': add driver uart-pl011 [ T1] bus: 'platform': add driver imx_mu [ T1] imx mu driver is registered. [ T1] bus: 'platform': add driver imx-rpmsg [ T1] imx rpmsg driver is registered. [ T1] device: 'psci': device_add [ T1] bus: 'platform': add device psci [ T1] PM: Adding info for platform:psci [ T1] device: 'reboot': device_add [ T1] bus: 'platform': add device reboot [ T1] PM: Adding info for platform:reboot [ T1] device: 'timer': device_add [ T1] bus: 'platform': add device timer [ T1] PM: Adding info for platform:timer [ T1] device: 'pmu': device_add [ T1] bus: 'platform': add device pmu [ T1] PM: Adding info for platform:pmu [ T1] device: 'soc': device_add [ T1] bus: 'platform': add device soc [ T1] PM: Adding info for platform:soc [ T1] ucc@2000 Linked as a fwnode consumer to qeic@80 [ T1] ucc@2200 Linked as a fwnode consumer to qeic@80 [ T1] device: '1570000.scfg': device_add [ T1] bus: 'platform': add device 1570000.scfg [ T1] PM: Adding info for platform:1570000.scfg [ T1] device: '1ee0000.dcfg': device_add [ T1] bus: 'platform': add device 1ee0000.dcfg [ T1] PM: Adding info for platform:1ee0000.dcfg [ T1] bus: 'platform': __driver_probe_device: matched device 1ee0000.dcfg with driver fsl-guts [ T1] bus: 'platform': really_probe: probing driver fsl-guts with device 1ee0000.dcfg [ T1] fsl-guts 1ee0000.dcfg: no pinctrl handle [ T1] device: 'soc0': device_add [ T1] bus: 'soc': add device soc0 [ T1] PM: Adding info for soc:soc0 [ T1] Machine: LS1043A RDB Board [ T1] SoC family: QorIQ LS1043A [ T1] SoC ID: svr:0x87920211, Revision: 1.1 [ T1] driver: 'fsl-guts': driver_bound: bound to device '1ee0000.dcfg' [ T1] devices_kset: Moving 1ee0000.dcfg to end of list [ T1] PM: Moving platform:1ee0000.dcfg to end of list [ T1] bus: 'platform': really_probe: bound device 1ee0000.dcfg to driver fsl-guts [ T1] device: '1530000.memory-controller': device_add [ T1] bus: 'platform': add device 1530000.memory-controller [ T1] PM: Adding info for platform:1530000.memory-controller [ T1] device: '1080000.memory-controller': device_add [ T1] bus: 'platform': add device 1080000.memory-controller [ T1] PM: Adding info for platform:1080000.memory-controller [ T1] device: '1880000.qman': device_add [ T1] bus: 'platform': add device 1880000.qman [ T1] PM: Adding info for platform:1880000.qman [ T1] device: '1890000.bman': device_add [ T1] bus: 'platform': add device 1890000.bman [ T1] PM: Adding info for platform:1890000.bman [ T1] device: 'soc:bman-portals@508000000': device_add [ T1] bus: 'platform': add device soc:bman-portals@508000000 [ T1] PM: Adding info for platform:soc:bman-portals@508000000 [ T1] device: '508000000.bman-portal': device_add [ T1] bus: 'platform': add device 508000000.bman-portal [ T1] PM: Adding info for platform:508000000.bman-portal [ T1] device: '508010000.bman-portal': device_add [ T1] bus: 'platform': add device 508010000.bman-portal [ T1] PM: Adding info for platform:508010000.bman-portal [ T1] device: '508020000.bman-portal': device_add [ T1] bus: 'platform': add device 508020000.bman-portal [ T1] PM: Adding info for platform:508020000.bman-portal [ T1] device: '508030000.bman-portal': device_add [ T1] bus: 'platform': add device 508030000.bman-portal [ T1] PM: Adding info for platform:508030000.bman-portal [ T1] device: '508040000.bman-portal': device_add [ T1] bus: 'platform': add device 508040000.bman-portal [ T1] PM: Adding info for platform:508040000.bman-portal [ T1] device: '508050000.bman-portal': device_add [ T1] bus: 'platform': add device 508050000.bman-portal [ T1] PM: Adding info for platform:508050000.bman-portal [ T1] device: '508060000.bman-portal': device_add [ T1] bus: 'platform': add device 508060000.bman-portal [ T1] PM: Adding info for platform:508060000.bman-portal [ T1] device: '508070000.bman-portal': device_add [ T1] bus: 'platform': add device 508070000.bman-portal [ T1] PM: Adding info for platform:508070000.bman-portal [ T1] device: '508080000.bman-portal': device_add [ T1] bus: 'platform': add device 508080000.bman-portal [ T1] PM: Adding info for platform:508080000.bman-portal [ T1] device: '508090000.bman-portal': device_add [ T1] bus: 'platform': add device 508090000.bman-portal [ T1] PM: Adding info for platform:508090000.bman-portal [ T1] device: 'soc:bman-portals@508000000:bman-bpids@0': device_add [ T1] bus: 'platform': add device soc:bman-portals@508000000:bman-bpids@0 [ T1] PM: Adding info for platform:soc:bman-portals@508000000:bman-bpids@0 [ T1] device: 'soc:qman-portals@500000000': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000 [ T1] PM: Adding info for platform:soc:qman-portals@500000000 [ T1] device: '500000000.qman-portal': device_add [ T1] bus: 'platform': add device 500000000.qman-portal [ T1] PM: Adding info for platform:500000000.qman-portal [ T1] device: '500010000.qman-portal': device_add [ T1] bus: 'platform': add device 500010000.qman-portal [ T1] PM: Adding info for platform:500010000.qman-portal [ T1] device: '500020000.qman-portal': device_add [ T1] bus: 'platform': add device 500020000.qman-portal [ T1] PM: Adding info for platform:500020000.qman-portal [ T1] device: '500030000.qman-portal': device_add [ T1] bus: 'platform': add device 500030000.qman-portal [ T1] PM: Adding info for platform:500030000.qman-portal [ T1] device: '500040000.qman-portal': device_add [ T1] bus: 'platform': add device 500040000.qman-portal [ T1] PM: Adding info for platform:500040000.qman-portal [ T1] device: '500050000.qman-portal': device_add [ T1] bus: 'platform': add device 500050000.qman-portal [ T1] PM: Adding info for platform:500050000.qman-portal [ T1] device: '500060000.qman-portal': device_add [ T1] bus: 'platform': add device 500060000.qman-portal [ T1] PM: Adding info for platform:500060000.qman-portal [ T1] device: '500070000.qman-portal': device_add [ T1] bus: 'platform': add device 500070000.qman-portal [ T1] PM: Adding info for platform:500070000.qman-portal [ T1] device: '500080000.qman-portal': device_add [ T1] bus: 'platform': add device 500080000.qman-portal [ T1] PM: Adding info for platform:500080000.qman-portal [ T1] device: '500090000.qman-portal': device_add [ T1] bus: 'platform': add device 500090000.qman-portal [ T1] PM: Adding info for platform:500090000.qman-portal [ T1] device: 'soc:qman-portals@500000000:qman-fqids@0': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000:qman-fqids@0 [ T1] PM: Adding info for platform:soc:qman-portals@500000000:qman-fqids@0 [ T1] device: 'soc:qman-portals@500000000:qman-fqids@1': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000:qman-fqids@1 [ T1] PM: Adding info for platform:soc:qman-portals@500000000:qman-fqids@1 [ T1] device: 'soc:qman-portals@500000000:qman-pools@0': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000:qman-pools@0 [ T1] PM: Adding info for platform:soc:qman-portals@500000000:qman-pools@0 [ T1] device: 'soc:qman-portals@500000000:qman-cgrids@0': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000:qman-cgrids@0 [ T1] PM: Adding info for platform:soc:qman-portals@500000000:qman-cgrids@0 [ T1] device: 'soc:qman-portals@500000000:qman-ceetm@0': device_add [ T1] bus: 'platform': add device soc:qman-portals@500000000:qman-ceetm@0 [ T1] PM: Adding info for platform:soc:qman-portals@500000000:qman-ceetm@0 [ T1] device: '2100000.spi': device_add [ T1] bus: 'platform': add device 2100000.spi [ T1] PM: Adding info for platform:2100000.spi [ T1] device: '2180000.i2c': device_add [ T1] bus: 'platform': add device 2180000.i2c [ T1] PM: Adding info for platform:2180000.i2c [ T1] device: '21b0000.i2c': device_add [ T1] bus: 'platform': add device 21b0000.i2c [ T1] PM: Adding info for platform:21b0000.i2c [ T1] device: '21c0500.serial': device_add [ T1] bus: 'platform': add device 21c0500.serial [ T1] PM: Adding info for platform:21c0500.serial [ T1] device: '21c0600.serial': device_add [ T1] bus: 'platform': add device 21c0600.serial [ T1] PM: Adding info for platform:21c0600.serial [ T1] device: '21d0500.serial': device_add [ T1] bus: 'platform': add device 21d0500.serial [ T1] PM: Adding info for platform:21d0500.serial [ T1] device: '21d0600.serial': device_add [ T1] bus: 'platform': add device 21d0600.serial [ T1] PM: Adding info for platform:21d0600.serial [ T1] device: '2300000.gpio': device_add [ T1] bus: 'platform': add device 2300000.gpio [ T1] PM: Adding info for platform:2300000.gpio [ T1] bus: 'platform': __driver_probe_device: matched device 2300000.gpio with driver gpio-mpc8xxx [ T1] bus: 'platform': really_probe: probing driver gpio-mpc8xxx with device 2300000.gpio [ T1] gpio-mpc8xxx 2300000.gpio: no pinctrl handle [ T1] device: 'gpiochip0': device_add [ T1] bus: 'gpio': add device gpiochip0 [ T1] PM: Adding info for gpio:gpiochip0 [ T1] driver: 'gpio-mpc8xxx': driver_bound: bound to device '2300000.gpio' [ T1] devices_kset: Moving 2300000.gpio to end of list [ T1] PM: Moving platform:2300000.gpio to end of list [ T1] devices_kset: Moving gpiochip0 to end of list [ T1] PM: Moving gpio:gpiochip0 to end of list [ T1] bus: 'platform': really_probe: bound device 2300000.gpio to driver gpio-mpc8xxx [ T1] device: '2310000.gpio': device_add [ T1] bus: 'platform': add device 2310000.gpio [ T1] PM: Adding info for platform:2310000.gpio [ T1] bus: 'platform': __driver_probe_device: matched device 2310000.gpio with driver gpio-mpc8xxx [ T1] bus: 'platform': really_probe: probing driver gpio-mpc8xxx with device 2310000.gpio [ T1] gpio-mpc8xxx 2310000.gpio: no pinctrl handle [ T1] device: 'gpiochip1': device_add [ T1] bus: 'gpio': add device gpiochip1 [ T1] PM: Adding info for gpio:gpiochip1 [ T1] driver: 'gpio-mpc8xxx': driver_bound: bound to device '2310000.gpio' [ T1] devices_kset: Moving 2310000.gpio to end of list [ T1] PM: Moving platform:2310000.gpio to end of list [ T1] devices_kset: Moving gpiochip1 to end of list [ T1] PM: Moving gpio:gpiochip1 to end of list [ T1] bus: 'platform': really_probe: bound device 2310000.gpio to driver gpio-mpc8xxx [ T1] device: '2320000.gpio': device_add [ T1] bus: 'platform': add device 2320000.gpio [ T1] PM: Adding info for platform:2320000.gpio [ T1] bus: 'platform': __driver_probe_device: matched device 2320000.gpio with driver gpio-mpc8xxx [ T1] bus: 'platform': really_probe: probing driver gpio-mpc8xxx with device 2320000.gpio [ T1] gpio-mpc8xxx 2320000.gpio: no pinctrl handle [ T1] device: 'gpiochip2': device_add [ T1] bus: 'gpio': add device gpiochip2 [ T1] PM: Adding info for gpio:gpiochip2 [ T1] driver: 'gpio-mpc8xxx': driver_bound: bound to device '2320000.gpio' [ T1] devices_kset: Moving 2320000.gpio to end of list [ T1] PM: Moving platform:2320000.gpio to end of list [ T1] devices_kset: Moving gpiochip2 to end of list [ T1] PM: Moving gpio:gpiochip2 to end of list [ T1] bus: 'platform': really_probe: bound device 2320000.gpio to driver gpio-mpc8xxx [ T1] device: '2400000.uqe': device_add [ T1] bus: 'platform': add device 2400000.uqe [ T1] PM: Adding info for platform:2400000.uqe [ T1] device: '2400080.qeic': device_add [ T1] bus: 'platform': add device 2400080.qeic [ T1] PM: Adding info for platform:2400080.qeic [ T1] device: '2400700.si': device_add [ T1] bus: 'platform': add device 2400700.si [ T1] PM: Adding info for platform:2400700.si [ T1] device: '2401000.siram': device_add [ T1] bus: 'platform': add device 2401000.siram [ T1] PM: Adding info for platform:2401000.siram [ T1] device: '2402000.ucc': device_add [ T1] bus: 'platform': add device 2402000.ucc [ T1] PM: Adding info for platform:2402000.ucc [ T1] device: 'platform:2400080.qeic--platform:2402000.ucc': device_add [ T1] devices_kset: Moving 2402000.ucc to end of list [ T1] PM: Moving platform:2402000.ucc to end of list [ T1] platform 2402000.ucc: Linked as a consumer to 2400080.qeic [ T1] ucc@2000 Dropping the fwnode link to qeic@80 [ T1] device: '2400000.uqe:muram@10000': device_add [ T1] bus: 'platform': add device 2400000.uqe:muram@10000 [ T1] PM: Adding info for platform:2400000.uqe:muram@10000 [ T1] device: '2970000.serial': device_add [ T1] bus: 'platform': add device 2970000.serial [ T1] PM: Adding info for platform:2970000.serial [ T1] device: '29a0000.serial': device_add [ T1] bus: 'platform': add device 29a0000.serial [ T1] PM: Adding info for platform:29a0000.serial [ T1] device: '2ad0000.watchdog': device_add [ T1] bus: 'platform': add device 2ad0000.watchdog [ T1] PM: Adding info for platform:2ad0000.watchdog [ T1] device: '2c00000.edma': device_add [ T1] bus: 'platform': add device 2c00000.edma [ T1] PM: Adding info for platform:2c00000.edma [ T1] device: '8380000.dma-controller': device_add [ T1] bus: 'platform': add device 8380000.dma-controller [ T1] PM: Adding info for platform:8380000.dma-controller [ T1] device: '1ee2140.power-controller': device_add [ T1] bus: 'platform': add device 1ee2140.power-controller [ T1] PM: Adding info for platform:1ee2140.power-controller [ T1] device: '29d0000.timer': device_add [ T1] bus: 'platform': add device 29d0000.timer [ T1] PM: Adding info for platform:29d0000.timer [ T1] device: '1a00000.fman': device_add [ T1] bus: 'platform': add device 1a00000.fman [ T1] PM: Adding info for platform:1a00000.fman [ T1] device: '1a00000.fman:fman-firmware': device_add [ T1] bus: 'platform': add device 1a00000.fman:fman-firmware [ T1] PM: Adding info for platform:1a00000.fman:fman-firmware [ T1] device: '1a00000.fman:cc': device_add [ T1] bus: 'platform': add device 1a00000.fman:cc [ T1] PM: Adding info for platform:1a00000.fman:cc [ T1] device: '1a00000.muram': device_add [ T1] bus: 'platform': add device 1a00000.muram [ T1] PM: Adding info for platform:1a00000.muram [ T1] device: '1a80000.bmi': device_add [ T1] bus: 'platform': add device 1a80000.bmi [ T1] PM: Adding info for platform:1a80000.bmi [ T1] device: '1a80400.qmi': device_add [ T1] bus: 'platform': add device 1a80400.qmi [ T1] PM: Adding info for platform:1a80400.qmi [ T1] device: '1a82000.port': device_add [ T1] bus: 'platform': add device 1a82000.port [ T1] PM: Adding info for platform:1a82000.port [ T1] device: '1a83000.port': device_add [ T1] bus: 'platform': add device 1a83000.port [ T1] PM: Adding info for platform:1a83000.port [ T1] device: '1a84000.port': device_add [ T1] bus: 'platform': add device 1a84000.port [ T1] PM: Adding info for platform:1a84000.port [ T1] device: '1a85000.port': device_add [ T1] bus: 'platform': add device 1a85000.port [ T1] PM: Adding info for platform:1a85000.port [ T1] device: '1a86000.port': device_add [ T1] bus: 'platform': add device 1a86000.port [ T1] PM: Adding info for platform:1a86000.port [ T1] device: '1a87000.port': device_add [ T1] bus: 'platform': add device 1a87000.port [ T1] PM: Adding info for platform:1a87000.port [ T1] device: '1ac0000.policer': device_add [ T1] bus: 'platform': add device 1ac0000.policer [ T1] PM: Adding info for platform:1ac0000.policer [ T1] device: '1ac1000.keygen': device_add [ T1] bus: 'platform': add device 1ac1000.keygen [ T1] PM: Adding info for platform:1ac1000.keygen [ T1] device: '1ac2000.dma': device_add [ T1] bus: 'platform': add device 1ac2000.dma [ T1] PM: Adding info for platform:1ac2000.dma [ T1] device: '1ac3000.fpm': device_add [ T1] bus: 'platform': add device 1ac3000.fpm [ T1] PM: Adding info for platform:1ac3000.fpm [ T1] device: '1ac7000.parser': device_add [ T1] bus: 'platform': add device 1ac7000.parser [ T1] PM: Adding info for platform:1ac7000.parser [ T1] device: '1adc000.vsps': device_add [ T1] bus: 'platform': add device 1adc000.vsps [ T1] PM: Adding info for platform:1adc000.vsps [ T1] device: '1afc000.mdio': device_add [ T1] bus: 'platform': add device 1afc000.mdio [ T1] PM: Adding info for platform:1afc000.mdio [ T1] device: '1afd000.mdio': device_add [ T1] bus: 'platform': add device 1afd000.mdio [ T1] PM: Adding info for platform:1afd000.mdio [ T1] device: '1a8a000.port': device_add [ T1] bus: 'platform': add device 1a8a000.port [ T1] PM: Adding info for platform:1a8a000.port [ T1] device: '1aaa000.port': device_add [ T1] bus: 'platform': add device 1aaa000.port [ T1] PM: Adding info for platform:1aaa000.port [ T1] device: '1ae4000.ethernet': device_add [ T1] bus: 'platform': add device 1ae4000.ethernet [ T1] PM: Adding info for platform:1ae4000.ethernet [ T1] device: '1ae5000.mdio': device_add [ T1] bus: 'platform': add device 1ae5000.mdio [ T1] PM: Adding info for platform:1ae5000.mdio [ T1] device: '1a8b000.port': device_add [ T1] bus: 'platform': add device 1a8b000.port [ T1] PM: Adding info for platform:1a8b000.port [ T1] device: '1aab000.port': device_add [ T1] bus: 'platform': add device 1aab000.port [ T1] PM: Adding info for platform:1aab000.port [ T1] device: '1ae6000.ethernet': device_add [ T1] bus: 'platform': add device 1ae6000.ethernet [ T1] PM: Adding info for platform:1ae6000.ethernet [ T1] device: '1ae7000.mdio': device_add [ T1] bus: 'platform': add device 1ae7000.mdio [ T1] PM: Adding info for platform:1ae7000.mdio [ T1] device: '1afe000.ptp-timer': device_add [ T1] bus: 'platform': add device 1afe000.ptp-timer [ T1] PM: Adding info for platform:1afe000.ptp-timer [ T1] device: 'soc:fsl,dpaa': device_add [ T1] bus: 'platform': add device soc:fsl,dpaa [ T1] PM: Adding info for platform:soc:fsl,dpaa [ T1] device: 'soc:fsl,dpaa:ethernet@2': device_add [ T1] bus: 'platform': add device soc:fsl,dpaa:ethernet@2 [ T1] PM: Adding info for platform:soc:fsl,dpaa:ethernet@2 [ T1] device: 'soc:fsl,dpaa:ethernet@3': device_add [ T1] bus: 'platform': add device soc:fsl,dpaa:ethernet@3 [ T1] PM: Adding info for platform:soc:fsl,dpaa:ethernet@3 [ T1] device: 'node0': device_add [ T1] bus: 'node': add device node0 [ T1] PM: Adding info for node:node0 [ T1] device: 'cpu0': device_add [ T1] bus: 'cpu': add device cpu0 [ T1] PM: Adding info for cpu:cpu0 [ T1] device: 'cpu1': device_add [ T1] bus: 'cpu': add device cpu1 [ T1] PM: Adding info for cpu:cpu1 [ T1] device: 'cpu2': device_add [ T1] bus: 'cpu': add device cpu2 [ T1] PM: Adding info for cpu:cpu2 [ T1] device: 'cpu3': device_add [ T1] bus: 'cpu': add device cpu3 [ T1] PM: Adding info for cpu:cpu3 [ T1] device: 'writeback': device_add [ T1] bus: 'workqueue': add device writeback [ T1] PM: Adding info for workqueue:writeback [ T1] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ T1] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ T1] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ T1] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ T1] cryptd: max_cpu_qlen set to 1000 [ T1] device class 'block': registering [ T1] device: 'blkcg_punt_bio': device_add [ T1] bus: 'workqueue': add device blkcg_punt_bio [ T1] PM: Adding info for workqueue:blkcg_punt_bio [ T1] raid6: skip pq benchmark and using algorithm neonx8 [ T1] raid6: using neon recovery algorithm [ T1] bus: 'i2c': add driver max732x [ T1] i2c-core: driver [max732x] registered [ T1] bus: 'platform': add driver gpio-mxc [ T1] bus: 'i2c': add driver pca953x [ T1] i2c-core: driver [pca953x] registered [ T1] ACPI: Interpreter disabled. [ T1] bus: 'pnp': registered [ T1] bus: 'platform': add driver fsl-edma [ T1] bus: 'platform': __driver_probe_device: matched device 2c00000.edma with driver fsl-edma [ T1] bus: 'platform': really_probe: probing driver fsl-edma with device 2c00000.edma [ T1] fsl-edma 2c00000.edma: no pinctrl handle [ T1] fsl-edma 2c00000.edma: WARN: Device release is not defined so it is not safe to unbind this driver while in use [ T1] device: 'dma0chan0': device_add [ T1] PM: Adding info for No Bus:dma0chan0 [ T1] device: 'dma0chan1': device_add [ T1] PM: Adding info for No Bus:dma0chan1 [ T1] device: 'dma0chan2': device_add [ T1] PM: Adding info for No Bus:dma0chan2 [ T1] device: 'dma0chan3': device_add [ T1] PM: Adding info for No Bus:dma0chan3 [ T1] device: 'dma0chan4': device_add [ T1] PM: Adding info for No Bus:dma0chan4 [ T1] device: 'dma0chan5': device_add [ T1] PM: Adding info for No Bus:dma0chan5 [ T1] device: 'dma0chan6': device_add [ T1] PM: Adding info for No Bus:dma0chan6 [ T1] device: 'dma0chan7': device_add [ T1] PM: Adding info for No Bus:dma0chan7 [ T1] device: 'dma0chan8': device_add [ T1] PM: Adding info for No Bus:dma0chan8 [ T1] device: 'dma0chan9': device_add [ T1] PM: Adding info for No Bus:dma0chan9 [ T1] device: 'dma0chan10': device_add [ T1] PM: Adding info for No Bus:dma0chan10 [ T1] device: 'dma0chan11': device_add [ T1] PM: Adding info for No Bus:dma0chan11 [ T1] device: 'dma0chan12': device_add [ T1] PM: Adding info for No Bus:dma0chan12 [ T1] device: 'dma0chan13': device_add [ T1] PM: Adding info for No Bus:dma0chan13 [ T1] device: 'dma0chan14': device_add [ T1] PM: Adding info for No Bus:dma0chan14 [ T1] device: 'dma0chan15': device_add [ T1] PM: Adding info for No Bus:dma0chan15 [ T1] device: 'dma0chan16': device_add [ T1] PM: Adding info for No Bus:dma0chan16 [ T1] device: 'dma0chan17': device_add [ T1] PM: Adding info for No Bus:dma0chan17 [ T1] device: 'dma0chan18': device_add [ T1] PM: Adding info for No Bus:dma0chan18 [ T1] device: 'dma0chan19': device_add [ T1] PM: Adding info for No Bus:dma0chan19 [ T1] device: 'dma0chan20': device_add [ T1] PM: Adding info for No Bus:dma0chan20 [ T1] device: 'dma0chan21': device_add [ T1] PM: Adding info for No Bus:dma0chan21 [ T1] device: 'dma0chan22': device_add [ T1] PM: Adding info for No Bus:dma0chan22 [ T1] device: 'dma0chan23': device_add [ T1] PM: Adding info for No Bus:dma0chan23 [ T1] device: 'dma0chan24': device_add [ T1] PM: Adding info for No Bus:dma0chan24 [ T1] device: 'dma0chan25': device_add [ T1] PM: Adding info for No Bus:dma0chan25 [ T1] device: 'dma0chan26': device_add [ T1] PM: Adding info for No Bus:dma0chan26 [ T1] device: 'dma0chan27': device_add [ T1] PM: Adding info for No Bus:dma0chan27 [ T1] device: 'dma0chan28': device_add [ T1] PM: Adding info for No Bus:dma0chan28 [ T1] device: 'dma0chan29': device_add [ T1] PM: Adding info for No Bus:dma0chan29 [ T1] device: 'dma0chan30': device_add [ T1] PM: Adding info for No Bus:dma0chan30 [ T1] device: 'dma0chan31': device_add [ T1] PM: Adding info for No Bus:dma0chan31 [ T1] driver: 'fsl-edma': driver_bound: bound to device '2c00000.edma' [ T1] devices_kset: Moving 2c00000.edma to end of list [ T1] PM: Moving platform:2c00000.edma to end of list [ T1] devices_kset: Moving dma0chan0 to end of list [ T1] PM: Moving No Bus:dma0chan0 to end of list [ T1] devices_kset: Moving dma0chan1 to end of list [ T1] PM: Moving No Bus:dma0chan1 to end of list [ T1] devices_kset: Moving dma0chan2 to end of list [ T1] PM: Moving No Bus:dma0chan2 to end of list [ T1] devices_kset: Moving dma0chan3 to end of list [ T1] PM: Moving No Bus:dma0chan3 to end of list [ T1] devices_kset: Moving dma0chan4 to end of list [ T1] PM: Moving No Bus:dma0chan4 to end of list [ T1] devices_kset: Moving dma0chan5 to end of list [ T1] PM: Moving No Bus:dma0chan5 to end of list [ T1] devices_kset: Moving dma0chan6 to end of list [ T1] PM: Moving No Bus:dma0chan6 to end of list [ T1] devices_kset: Moving dma0chan7 to end of list [ T1] PM: Moving No Bus:dma0chan7 to end of list [ T1] devices_kset: Moving dma0chan8 to end of list [ T1] PM: Moving No Bus:dma0chan8 to end of list [ T1] devices_kset: Moving dma0chan9 to end of list [ T1] PM: Moving No Bus:dma0chan9 to end of list [ T1] devices_kset: Moving dma0chan10 to end of list [ T1] PM: Moving No Bus:dma0chan10 to end of list [ T1] devices_kset: Moving dma0chan11 to end of list [ T1] PM: Moving No Bus:dma0chan11 to end of list [ T1] devices_kset: Moving dma0chan12 to end of list [ T1] PM: Moving No Bus:dma0chan12 to end of list [ T1] devices_kset: Moving dma0chan13 to end of list [ T1] PM: Moving No Bus:dma0chan13 to end of list [ T1] devices_kset: Moving dma0chan14 to end of list [ T1] PM: Moving No Bus:dma0chan14 to end of list [ T1] devices_kset: Moving dma0chan15 to end of list [ T1] PM: Moving No Bus:dma0chan15 to end of list [ T1] devices_kset: Moving dma0chan16 to end of list [ T1] PM: Moving No Bus:dma0chan16 to end of list [ T1] devices_kset: Moving dma0chan17 to end of list [ T1] PM: Moving No Bus:dma0chan17 to end of list [ T1] devices_kset: Moving dma0chan18 to end of list [ T1] PM: Moving No Bus:dma0chan18 to end of list [ T1] devices_kset: Moving dma0chan19 to end of list [ T1] PM: Moving No Bus:dma0chan19 to end of list [ T1] devices_kset: Moving dma0chan20 to end of list [ T1] PM: Moving No Bus:dma0chan20 to end of list [ T1] devices_kset: Moving dma0chan21 to end of list [ T1] PM: Moving No Bus:dma0chan21 to end of list [ T1] devices_kset: Moving dma0chan22 to end of list [ T1] PM: Moving No Bus:dma0chan22 to end of list [ T1] devices_kset: Moving dma0chan23 to end of list [ T1] PM: Moving No Bus:dma0chan23 to end of list [ T1] devices_kset: Moving dma0chan24 to end of list [ T1] PM: Moving No Bus:dma0chan24 to end of list [ T1] devices_kset: Moving dma0chan25 to end of list [ T1] PM: Moving No Bus:dma0chan25 to end of list [ T1] devices_kset: Moving dma0chan26 to end of list [ T1] PM: Moving No Bus:dma0chan26 to end of list [ T1] devices_kset: Moving dma0chan27 to end of list [ T1] PM: Moving No Bus:dma0chan27 to end of list [ T1] devices_kset: Moving dma0chan28 to end of list [ T1] PM: Moving No Bus:dma0chan28 to end of list [ T1] devices_kset: Moving dma0chan29 to end of list [ T1] PM: Moving No Bus:dma0chan29 to end of list [ T1] devices_kset: Moving dma0chan30 to end of list [ T1] PM: Moving No Bus:dma0chan30 to end of list [ T1] devices_kset: Moving dma0chan31 to end of list [ T1] PM: Moving No Bus:dma0chan31 to end of list [ T1] bus: 'platform': really_probe: bound device 2c00000.edma to driver fsl-edma [ T1] bus: 'platform': add driver imx-dma [ T1] bus: 'platform': remove driver imx-dma [ T1] driver: 'imx-dma': driver_release [ T1] bus: 'xen-backend': registered [ T1] bus: 'xen': registered [ T1] bus: 'platform': add driver reg-fixed-voltage [ T1] bus: 'platform': add driver gpio-regulator [ T1] bus: 'i2c': add driver max8973 [ T1] i2c-core: driver [max8973] registered [ T1] device class 'misc': registering [ T1] device class 'tpm': registering [ T1] device class 'tpmrm': registering [ T1] iommu: Default domain type: Passthrough [ T1] bus: 'i2c': add driver fp9931 [ T1] i2c-core: driver [fp9931] registered [ T1] bus: 'i2c': add driver rohm-bd718x7 [ T1] i2c-core: driver [rohm-bd718x7] registered [ T1] device class 'mdio_bus': registering [ T1] bus: 'mdio_bus': registered [ T1] bus: 'mdio_bus': add driver Generic Clause 45 PHY [ T1] bus: 'mdio_bus': add driver Generic PHY [ T1] bus: 'serio': registered [ T1] device class 'input': registering [ T1] device class 'rtc': registering [ T1] bus: 'platform': add driver imx-i2c [ T1] bus: 'platform': __driver_probe_device: matched device 2180000.i2c with driver imx-i2c [ T1] bus: 'platform': really_probe: probing driver imx-i2c with device 2180000.i2c [ T1] imx-i2c 2180000.i2c: no pinctrl handle [ T1] (null): I2C_CLK=400000000, REQ DIV=4000 [ T1] (null): IFDR[IC]=0x7b, REAL DIV=4096 [ T1] imx-i2c 2180000.i2c: scl-gpios not found [ T1] device: 'i2c-0': device_add [ T1] bus: 'i2c': add device i2c-0 [ T1] PM: Adding info for i2c:i2c-0 [ T1] i2c i2c-0: adapter [2180000.i2c] registered [ T1] i2c i2c-0: of_i2c: walking child nodes [ T1] i2c i2c-0: of_i2c: register /soc/i2c@2180000/eeprom@50 [ T1] device: '0-0050': device_add [ T1] bus: 'i2c': add device 0-0050 [ T1] PM: Adding info for i2c:0-0050 [ T1] i2c i2c-0: client [at24cm01] registered with bus id 0-0050 [ T1] i2c i2c-0: claimed irq 42 [ T1] i2c i2c-0: device resources: [mem 0x02180000-0x0218ffff] [ T1] i2c i2c-0: adapter name: "2180000.i2c" [ T1] i2c i2c-0: IMX I2C adapter registered [ T1] driver: 'imx-i2c': driver_bound: bound to device '2180000.i2c' [ T1] devices_kset: Moving 2180000.i2c to end of list [ T1] PM: Moving platform:2180000.i2c to end of list [ T1] devices_kset: Moving i2c-0 to end of list [ T1] PM: Moving i2c:i2c-0 to end of list [ T1] devices_kset: Moving 0-0050 to end of list [ T1] PM: Moving i2c:0-0050 to end of list [ T1] bus: 'platform': really_probe: bound device 2180000.i2c to driver imx-i2c [ T1] bus: 'platform': __driver_probe_device: matched device 21b0000.i2c with driver imx-i2c [ T1] bus: 'platform': really_probe: probing driver imx-i2c with device 21b0000.i2c [ T1] imx-i2c 21b0000.i2c: no pinctrl handle [ T1] (null): I2C_CLK=400000000, REQ DIV=4000 [ T1] (null): IFDR[IC]=0x7b, REAL DIV=4096 [ T1] imx-i2c 21b0000.i2c: can't get pinctrl, bus recovery not supported [ T1] device: 'i2c-1': device_add [ T1] bus: 'i2c': add device i2c-1 [ T1] PM: Adding info for i2c:i2c-1 [ T1] i2c i2c-1: adapter [21b0000.i2c] registered [ T1] i2c i2c-1: of_i2c: walking child nodes [ T1] i2c i2c-1: of_i2c: register /soc/i2c@21b0000/rtc@68 [ T1] device: '1-0068': device_add [ T1] bus: 'i2c': add device 1-0068 [ T1] PM: Adding info for i2c:1-0068 [ T1] i2c i2c-1: client [ds3232] registered with bus id 1-0068 [ T1] i2c i2c-1: of_i2c: register /soc/i2c@21b0000/pca9554@42 [ T1] device: '1-0021': device_add [ T1] bus: 'i2c': add device 1-0021 [ T1] PM: Adding info for i2c:1-0021 [ T1] bus: 'i2c': __driver_probe_device: matched device 1-0021 with driver pca953x [ T1] bus: 'i2c': really_probe: probing driver pca953x with device 1-0021 [ T1] pca953x 1-0021: no pinctrl handle [ T1] pca953x 1-0021: probe [ T1] pca953x 1-0021: supply vcc not found, using dummy regulator [ T1] device: 'regulator:regulator.0--i2c:1-0021': device_add [ T1] devices_kset: Moving 1-0021 to end of list [ T1] PM: Moving i2c:1-0021 to end of list [ T1] pca953x 1-0021: Linked as a consumer to regulator.0 [ T1] pca953x 1-0021: using no AI [ T1] i2c i2c-1: exit with: error: -11 [ T1] pca953x 1-0021: failed writing register [ T1] pca953x 1-0021: Dropping the link to regulator.0 [ T1] device: 'regulator:regulator.0--i2c:1-0021': device_unregister [ T1] pca953x: probe of 1-0021 failed with error -11 [ T1] i2c i2c-1: client [pca9554] registered with bus id 1-0021 [ T1] i2c i2c-1: claimed irq 43 [ T1] i2c i2c-1: device resources: [mem 0x021b0000-0x021bffff] [ T1] i2c i2c-1: adapter name: "21b0000.i2c" [ T1] i2c i2c-1: IMX I2C adapter registered [ T1] driver: 'imx-i2c': driver_bound: bound to device '21b0000.i2c' [ T1] devices_kset: Moving 21b0000.i2c to end of list [ T1] PM: Moving platform:21b0000.i2c to end of list [ T1] devices_kset: Moving i2c-1 to end of list [ T1] PM: Moving i2c:i2c-1 to end of list [ T1] devices_kset: Moving 1-0068 to end of list [ T1] PM: Moving i2c:1-0068 to end of list [ T1] devices_kset: Moving 1-0021 to end of list [ T1] PM: Moving i2c:1-0021 to end of list [ T1] bus: 'platform': really_probe: bound device 21b0000.i2c to driver imx-i2c [ T1] bus: 'platform': add driver imx-lpi2c [ T1] device class 'pps': registering [ T1] pps_core: LinuxPPS API ver. 1 registered [ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ T1] device class 'ptp': registering [ T1] PTP clock support registered [ T1] bus: 'platform': add driver brcmstb-reboot [ T1] bus: 'platform': remove driver brcmstb-reboot [ T1] driver: 'brcmstb-reboot': driver_release [ T1] device class 'power_supply': registering [ T1] device class 'hwmon': registering [ T1] EDAC MC: Ver: 3.0.0 [ T1] bus: 'edac': registered [ T1] device: 'edac': device_add [ T1] PM: Adding info for No Bus:edac [ T1] device: 'mc': device_add [ T1] bus: 'edac': add device mc [ T1] PM: Adding info for edac:mc [ T1] bus: 'platform': add driver psci-cpuidle-domain [ T1] bus: 'platform': __driver_probe_device: matched device psci with driver psci-cpuidle-domain [ T1] bus: 'platform': really_probe: probing driver psci-cpuidle-domain with device psci [ T1] psci-cpuidle-domain psci: no pinctrl handle [ T1] driver: 'psci-cpuidle-domain': driver_bound: bound to device 'psci' [ T1] devices_kset: Moving psci to end of list [ T1] PM: Moving platform:psci to end of list [ T1] bus: 'platform': really_probe: bound device psci to driver psci-cpuidle-domain [ T1] bus: 'scmi_protocol': registered [ T1] bus: 'platform': add driver arm-scmi [ T1] bman-fbpr addr 0x00000000ba000000 size 0x1000000 [ T1] Bman err interrupt handler present [ T1] Registering platform device 'bportal-9'. Parent at platform [ T1] device: 'bportal-9': device_add [ T1] bus: 'platform': add device bportal-9 [ T1] PM: Adding info for platform:bportal-9 [ T1] Bman portal initialised, cpu 0 [ T1] Registering platform device 'bportal-8'. Parent at platform [ T1] device: 'bportal-8': device_add [ T1] bus: 'platform': add device bportal-8 [ T1] PM: Adding info for platform:bportal-8 [ T1] Bman portal initialised, cpu 1 [ T1] Registering platform device 'bportal-7'. Parent at platform [ T1] device: 'bportal-7': device_add [ T1] bus: 'platform': add device bportal-7 [ T1] PM: Adding info for platform:bportal-7 [ T1] Bman portal initialised, cpu 2 [ T1] Registering platform device 'bportal-6'. Parent at platform [ T1] device: 'bportal-6': device_add [ T1] bus: 'platform': add device bportal-6 [ T1] PM: Adding info for platform:bportal-6 [ T1] Bman portal initialised, cpu 3 [ T1] Bman portals initialised [ T1] Qman err interrupt handler present [ T1] QMan: Allocated lookup table at (____ptrval____), entry count 65537 [ T1] Registering platform device 'qportal-9'. Parent at platform [ T1] device: 'qportal-9': device_add [ T1] bus: 'platform': add device qportal-9 [ T1] PM: Adding info for platform:qportal-9 [ T1] Qman portal initialised, cpu 0 [ T1] Registering platform device 'qportal-8'. Parent at platform [ T1] device: 'qportal-8': device_add [ T1] bus: 'platform': add device qportal-8 [ T1] PM: Adding info for platform:qportal-8 [ T1] Qman portal initialised, cpu 1 [ T1] Registering platform device 'qportal-7'. Parent at platform [ T1] device: 'qportal-7': device_add [ T1] bus: 'platform': add device qportal-7 [ T1] PM: Adding info for platform:qportal-7 [ T1] Qman portal initialised, cpu 2 [ T1] Registering platform device 'qportal-6'. Parent at platform [ T1] device: 'qportal-6': device_add [ T1] bus: 'platform': add device qportal-6 [ T1] PM: Adding info for platform:qportal-6 [ T1] Qman portal initialised, cpu 3 [ T1] Qman portals initialised [ T1] Bman: BPID allocator includes range 32:32 [ T1] Qman: FQID allocator includes range 256:256 [ T1] Qman: FQID allocator includes range 32768:32768 [ T1] Qman: CGRID allocator includes range 0:256 [ T1] Qman: pool channel allocator includes range 1025:15 [ T1] No USDPAA memory, no 'fsl,usdpaa-mem' in device-tree [ T1] device class 'remoteproc': registering [ T1] bus: 'platform': add driver qcom_glink_rpm [ T1] bus: 'virtio': add driver virtio_rpmsg_bus [ T1] device class 'devfreq': registering [ T1] bus: 'iio': registered [ T1] bus: 'nvmem': registered [ T1] FPGA manager framework [ T1] device class 'fpga_manager': registering [ T1] device class 'tee': registering [ T1] bus: 'tee': registered [ T1] device class 'mux': registering [ T1] bus: 'counter': registered [ T1] device class 'net': registering [ T1] device: 'lo': device_add [ T1] PM: Adding info for No Bus:lo [ T1] bus: 'platform': add driver fp9931-pmic [ T1] device class 'watchdog': registering [ T1] clocksource: Switched to clocksource arch_sys_counter [ T1] VFS: Disk quotas dquot_6.6.0 [ T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ T1] bus: 'pnp': add driver system [ T1] pnp: PnP ACPI: disabled [ T1] bus: 'platform': add driver fsl-edma-v3 [ T1] device class 'mem': registering [ T1] device: 'mem': device_add [ T1] PM: Adding info for No Bus:mem [ T1] device: 'null': device_add [ T1] PM: Adding info for No Bus:null [ T1] device: 'zero': device_add [ T1] PM: Adding info for No Bus:zero [ T1] device: 'full': device_add [ T1] PM: Adding info for No Bus:full [ T1] device: 'random': device_add [ T1] PM: Adding info for No Bus:random [ T1] device: 'urandom': device_add [ T1] PM: Adding info for No Bus:urandom [ T1] device: 'kmsg': device_add [ T1] PM: Adding info for No Bus:kmsg [ T1] device: 'tty': device_add [ T1] PM: Adding info for No Bus:tty [ T1] device: 'console': device_add [ T1] PM: Adding info for No Bus:console [ T1] device: 'tty0': device_add [ T1] PM: Adding info for No Bus:tty0 [ T1] device class 'vc': registering [ T1] device: 'vcs': device_add [ T1] PM: Adding info for No Bus:vcs [ T1] device: 'vcsu': device_add [ T1] PM: Adding info for No Bus:vcsu [ T1] device: 'vcsa': device_add [ T1] PM: Adding info for No Bus:vcsa [ T1] device: 'vcs1': device_add [ T1] PM: Adding info for No Bus:vcs1 [ T1] device: 'vcsu1': device_add [ T1] PM: Adding info for No Bus:vcsu1 [ T1] device: 'vcsa1': device_add [ T1] PM: Adding info for No Bus:vcsa1 [ T1] device: 'tty1': device_add [ T1] PM: Adding info for No Bus:tty1 [ T1] device: 'tty2': device_add [ T1] PM: Adding info for No Bus:tty2 [ T1] device: 'tty3': device_add [ T1] PM: Adding info for No Bus:tty3 [ T1] device: 'tty4': device_add [ T1] PM: Adding info for No Bus:tty4 [ T1] device: 'tty5': device_add [ T1] PM: Adding info for No Bus:tty5 [ T1] device: 'tty6': device_add [ T1] PM: Adding info for No Bus:tty6 [ T1] device: 'tty7': device_add [ T1] PM: Adding info for No Bus:tty7 [ T1] device: 'tty8': device_add [ T1] PM: Adding info for No Bus:tty8 [ T1] device: 'tty9': device_add [ T1] PM: Adding info for No Bus:tty9 [ T1] device: 'tty10': device_add [ T1] PM: Adding info for No Bus:tty10 [ T1] device: 'tty11': device_add [ T1] PM: Adding info for No Bus:tty11 [ T1] device: 'tty12': device_add [ T1] PM: Adding info for No Bus:tty12 [ T1] device: 'tty13': device_add [ T1] PM: Adding info for No Bus:tty13 [ T1] device: 'tty14': device_add [ T1] PM: Adding info for No Bus:tty14 [ T1] device: 'tty15': device_add [ T1] PM: Adding info for No Bus:tty15 [ T1] device: 'tty16': device_add [ T1] PM: Adding info for No Bus:tty16 [ T1] device: 'tty17': device_add [ T1] PM: Adding info for No Bus:tty17 [ T1] device: 'tty18': device_add [ T1] PM: Adding info for No Bus:tty18 [ T1] device: 'tty19': device_add [ T1] PM: Adding info for No Bus:tty19 [ T1] device: 'tty20': device_add [ T1] PM: Adding info for No Bus:tty20 [ T1] device: 'tty21': device_add [ T1] PM: Adding info for No Bus:tty21 [ T1] device: 'tty22': device_add [ T1] PM: Adding info for No Bus:tty22 [ T1] device: 'tty23': device_add [ T1] PM: Adding info for No Bus:tty23 [ T1] device: 'tty24': device_add [ T1] PM: Adding info for No Bus:tty24 [ T1] device: 'tty25': device_add [ T1] PM: Adding info for No Bus:tty25 [ T1] device: 'tty26': device_add [ T1] PM: Adding info for No Bus:tty26 [ T1] device: 'tty27': device_add [ T1] PM: Adding info for No Bus:tty27 [ T1] device: 'tty28': device_add [ T1] PM: Adding info for No Bus:tty28 [ T1] device: 'tty29': device_add [ T1] PM: Adding info for No Bus:tty29 [ T1] device: 'tty30': device_add [ T1] PM: Adding info for No Bus:tty30 [ T1] device: 'tty31': device_add [ T1] PM: Adding info for No Bus:tty31 [ T1] device: 'tty32': device_add [ T1] PM: Adding info for No Bus:tty32 [ T1] device: 'tty33': device_add [ T1] PM: Adding info for No Bus:tty33 [ T1] device: 'tty34': device_add [ T1] PM: Adding info for No Bus:tty34 [ T1] device: 'tty35': device_add [ T1] PM: Adding info for No Bus:tty35 [ T1] device: 'tty36': device_add [ T1] PM: Adding info for No Bus:tty36 [ T1] device: 'tty37': device_add [ T1] PM: Adding info for No Bus:tty37 [ T1] device: 'tty38': device_add [ T1] PM: Adding info for No Bus:tty38 [ T1] device: 'tty39': device_add [ T1] PM: Adding info for No Bus:tty39 [ T1] device: 'tty40': device_add [ T1] PM: Adding info for No Bus:tty40 [ T1] device: 'tty41': device_add [ T1] PM: Adding info for No Bus:tty41 [ T1] device: 'tty42': device_add [ T1] PM: Adding info for No Bus:tty42 [ T1] device: 'tty43': device_add [ T1] PM: Adding info for No Bus:tty43 [ T1] device: 'tty44': device_add [ T1] PM: Adding info for No Bus:tty44 [ T1] device: 'tty45': device_add [ T1] PM: Adding info for No Bus:tty45 [ T1] device: 'tty46': device_add [ T1] PM: Adding info for No Bus:tty46 [ T1] device: 'tty47': device_add [ T1] PM: Adding info for No Bus:tty47 [ T1] device: 'tty48': device_add [ T1] PM: Adding info for No Bus:tty48 [ T1] device: 'tty49': device_add [ T1] PM: Adding info for No Bus:tty49 [ T1] device: 'tty50': device_add [ T1] PM: Adding info for No Bus:tty50 [ T1] device: 'tty51': device_add [ T1] PM: Adding info for No Bus:tty51 [ T1] device: 'tty52': device_add [ T1] PM: Adding info for No Bus:tty52 [ T1] device: 'tty53': device_add [ T1] PM: Adding info for No Bus:tty53 [ T1] device: 'tty54': device_add [ T1] PM: Adding info for No Bus:tty54 [ T1] device: 'tty55': device_add [ T1] PM: Adding info for No Bus:tty55 [ T1] device: 'tty56': device_add [ T1] PM: Adding info for No Bus:tty56 [ T1] device: 'tty57': device_add [ T1] PM: Adding info for No Bus:tty57 [ T1] device: 'tty58': device_add [ T1] PM: Adding info for No Bus:tty58 [ T1] device: 'tty59': device_add [ T1] PM: Adding info for No Bus:tty59 [ T1] device: 'tty60': device_add [ T1] PM: Adding info for No Bus:tty60 [ T1] device: 'tty61': device_add [ T1] PM: Adding info for No Bus:tty61 [ T1] device: 'tty62': device_add [ T1] PM: Adding info for No Bus:tty62 [ T1] device: 'tty63': device_add [ T1] PM: Adding info for No Bus:tty63 [ T1] device class 'firmware': registering [ T1] NET: Registered PF_INET protocol family [ T1] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ T1] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ T1] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ T1] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ T1] TCP: Hash tables configured (established 8192 bind 8192) [ T1] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ T1] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ T1] RPC: Registered named UNIX socket transport module. [ T1] RPC: Registered udp transport module. [ T1] RPC: Registered tcp transport module. [ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ T1] device class 'ieee80211': registering [ T1] Registering platform device 'regulatory.0'. Parent at platform [ T1] device: 'regulatory.0': device_add [ T1] bus: 'platform': add device regulatory.0 [ T1] PM: Adding info for platform:regulatory.0 [ T1] NET: Registered PF_XDP protocol family [ T8] Trying to unpack rootfs image as initramfs... [ T1] bus: 'platform': add driver armv8-pmu [ T1] bus: 'platform': __driver_probe_device: matched device pmu with driver armv8-pmu [ T1] bus: 'platform': really_probe: probing driver armv8-pmu with device pmu [ T1] armv8-pmu pmu: no pinctrl handle [ T1] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ T1] driver: 'armv8-pmu': driver_bound: bound to device 'pmu' [ T1] devices_kset: Moving pmu to end of list [ T1] PM: Moving platform:pmu to end of list [ T1] bus: 'platform': really_probe: bound device pmu to driver armv8-pmu [ T1] kvm [1]: IPA Size Limit: 40 bits [ T1] kvm [1]: vgic interrupt IRQ9 [ T1] kvm [1]: Hyp mode initialized successfully [ T1] device: 'kvm': device_add [ T1] PM: Adding info for No Bus:kvm [ T8] Freeing initrd memory: 42992K [ T1] bus: 'clocksource': registered [ T1] device: 'clocksource': device_add [ T1] PM: Adding info for No Bus:clocksource [ T1] device: 'clocksource0': device_add [ T1] bus: 'clocksource': add device clocksource0 [ T1] PM: Adding info for clocksource:clocksource0 [ T1] bus: 'platform': add driver alarmtimer [ T1] bus: 'clockevents': registered [ T1] device: 'clockevents': device_add [ T1] PM: Adding info for No Bus:clockevents [ T1] device: 'clockevent0': device_add [ T1] bus: 'clockevents': add device clockevent0 [ T1] PM: Adding info for clockevents:clockevent0 [ T1] device: 'clockevent1': device_add [ T1] bus: 'clockevents': add device clockevent1 [ T1] PM: Adding info for clockevents:clockevent1 [ T1] device: 'clockevent2': device_add [ T1] bus: 'clockevents': add device clockevent2 [ T1] PM: Adding info for clockevents:clockevent2 [ T1] device: 'clockevent3': device_add [ T1] bus: 'clockevents': add device clockevent3 [ T1] PM: Adding info for clockevents:clockevent3 [ T1] device: 'broadcast': device_add [ T1] bus: 'clockevents': add device broadcast [ T1] PM: Adding info for clockevents:broadcast [ T1] bus: 'event_source': registered [ T1] device: 'software': device_add [ T1] bus: 'event_source': add device software [ T1] PM: Adding info for event_source:software [ T1] device: 'breakpoint': device_add [ T1] bus: 'event_source': add device breakpoint [ T1] PM: Adding info for event_source:breakpoint [ T1] device: 'armv8_pmuv3': device_add [ T1] bus: 'event_source': add device armv8_pmuv3 [ T1] PM: Adding info for event_source:armv8_pmuv3 [ T1] Initialise system trusted keyrings [ T1] workingset: timestamp_bits=42 max_order=18 bucket_order=0 [ T1] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ T1] NFS: Registering the id_resolver key type [ T1] Key type id_resolver registered [ T1] Key type id_legacy registered [ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ T1] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ T1] device: 'autofs': device_add [ T1] PM: Adding info for No Bus:autofs [ T1] fuse: init (API version 7.34) [ T1] device: 'fuse': device_add [ T1] PM: Adding info for No Bus:fuse [ T1] NET: Registered PF_ALG protocol family [ T1] xor: measuring software checksum speed [ T1] 8regs : 3154 MB/sec [ T1] 32regs : 3736 MB/sec [ T1] arm64_neon : 3094 MB/sec [ T1] xor: using function: 32regs (3736 MB/sec) [ T1] Key type asymmetric registered [ T1] Asymmetric key parser 'x509' registered [ T1] device class 'bsg': registering [ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ T1] io scheduler mq-deadline registered [ T1] io scheduler kyber registered [ T1] bus: 'platform': add driver imx-irqsteer [ T1] bus: 'platform': add driver imx-intmux [ T1] bus: 'platform': add driver simple-pm-bus [ T1] device class 'phy': registering [ T1] bus: 'platform': add driver xgene-phy [ T1] bus: 'platform': add driver mixel-lvds-phy [ T1] bus: 'platform': add driver mixel-lvds-combo-phy [ T1] bus: 'platform': add driver cdns-salvo-phy [ T1] bus: 'platform': add driver imx8mp-lvds-phy [ T1] bus: 'platform': add driver imx8mq-usb-phy [ T1] bus: 'platform': add driver mixel-mipi-dphy [ T1] bus: 'platform': add driver samsung-hdmi-phy [ T1] bus: 'platform': add driver imx8-pcie-phy [ T1] bus: 'platform': add driver lynx-28g [ T1] bus: 'platform': add driver max77620-pinctrl [ T1] bus: 'platform': add driver pinctrl-single [ T1] bus: 'platform': add driver basic-mmio-gpio [ T1] bus: 'platform': add driver gpio-dwapb [ T1] bus: 'platform': add driver max77620-gpio [ T1] bus: 'platform': add driver mb86s70-gpio [ T1] bus: 'amba': add driver pl061_gpio [ T1] bus: 'platform': add driver gpio-vf610 [ T1] bus: 'rpmsg': add driver gpio_rpmsg [ T1] bus: 'platform': add driver xgene-gpio [ T1] bus: 'platform': add driver acpi-ged [ T1] bus: 'platform': add driver acpi-fan [ T1] EINJ: ACPI disabled. [ T1] bus: 'platform': add driver of_fixed_factor_clk [ T1] bus: 'platform': add driver of_fixed_clk [ T1] bus: 'platform': add driver gpio-clk [ T1] bus: 'i2c': add driver cs2000-cp [ T1] i2c-core: driver [cs2000-cp] registered [ T1] bus: 'platform': add driver fsl-flexspi-clk [ T1] bus: 'platform': add driver fsl-sai-clk [ T1] bus: 'platform': add driver plldig-clock [ T1] Registering platform device 'qoriq-cpufreq'. Parent at platform [ T1] device: 'qoriq-cpufreq': device_add [ T1] bus: 'platform': add device qoriq-cpufreq [ T1] PM: Adding info for platform:qoriq-cpufreq [ T1] bus: 'platform': add driver rk808-clkout [ T1] bus: 'platform': add driver s2mps11-clk [ T1] bus: 'scmi_protocol': add driver scmi-clocks [ T1] bus: 'platform': add driver scpi_clocks [ T1] bus: 'i2c': add driver vc5 [ T1] i2c-core: driver [vc5] registered [ T1] bus: 'platform': add driver imx8mm-ccm [ T1] bus: 'platform': add driver imx8mn-ccm [ T1] bus: 'platform': add driver imx8mp-ccm [ T1] bus: 'platform': add driver imx-blk-ctrl [ T1] bus: 'platform': add driver imx8mq-ccm [ T1] bus: 'platform': add driver clk_imx8ulp [ T1] bus: 'platform': add driver fsl-qdma [ T1] bus: 'platform': __driver_probe_device: matched device 8380000.dma-controller with driver fsl-qdma [ T1] bus: 'platform': really_probe: probing driver fsl-qdma with device 8380000.dma-controller [ T1] fsl-qdma 8380000.dma-controller: no pinctrl handle [ T1] fsl-qdma 8380000.dma-controller: WARN: Device release is not defined so it is not safe to unbind this driver while in use [ T1] device: 'dma1chan0': device_add [ T1] PM: Adding info for No Bus:dma1chan0 [ T1] device: 'dma1chan1': device_add [ T1] PM: Adding info for No Bus:dma1chan1 [ T1] device: 'dma1chan2': device_add [ T1] PM: Adding info for No Bus:dma1chan2 [ T1] device: 'dma1chan3': device_add [ T1] PM: Adding info for No Bus:dma1chan3 [ T1] device: 'dma1chan4': device_add [ T1] PM: Adding info for No Bus:dma1chan4 [ T1] device: 'dma1chan5': device_add [ T1] PM: Adding info for No Bus:dma1chan5 [ T1] device: 'dma1chan6': device_add [ T1] PM: Adding info for No Bus:dma1chan6 [ T1] device: 'dma1chan7': device_add [ T1] PM: Adding info for No Bus:dma1chan7 [ T1] driver: 'fsl-qdma': driver_bound: bound to device '8380000.dma-controller' [ T1] devices_kset: Moving 8380000.dma-controller to end of list [ T1] PM: Moving platform:8380000.dma-controller to end of list [ T1] devices_kset: Moving dma1chan0 to end of list [ T1] PM: Moving No Bus:dma1chan0 to end of list [ T1] devices_kset: Moving dma1chan1 to end of list [ T1] PM: Moving No Bus:dma1chan1 to end of list [ T1] devices_kset: Moving dma1chan2 to end of list [ T1] PM: Moving No Bus:dma1chan2 to end of list [ T1] devices_kset: Moving dma1chan3 to end of list [ T1] PM: Moving No Bus:dma1chan3 to end of list [ T1] devices_kset: Moving dma1chan4 to end of list [ T1] PM: Moving No Bus:dma1chan4 to end of list [ T1] devices_kset: Moving dma1chan5 to end of list [ T1] PM: Moving No Bus:dma1chan5 to end of list [ T1] devices_kset: Moving dma1chan6 to end of list [ T1] PM: Moving No Bus:dma1chan6 to end of list [ T1] devices_kset: Moving dma1chan7 to end of list [ T1] PM: Moving No Bus:dma1chan7 to end of list [ T1] bus: 'platform': really_probe: bound device 8380000.dma-controller to driver fsl-qdma [ T1] bus: 'platform': add driver imx-sdma [ T1] bus: 'amba': add driver dma-pl330 [ T1] bus: 'platform': add driver rcpm [ T1] bus: 'platform': __driver_probe_device: matched device 1ee2140.power-controller with driver rcpm [ T1] bus: 'platform': really_probe: probing driver rcpm with device 1ee2140.power-controller [ T1] rcpm 1ee2140.power-controller: no pinctrl handle [ T1] driver: 'rcpm': driver_bound: bound to device '1ee2140.power-controller' [ T1] devices_kset: Moving 1ee2140.power-controller to end of list [ T1] PM: Moving platform:1ee2140.power-controller to end of list [ T1] bus: 'platform': really_probe: bound device 1ee2140.power-controller to driver rcpm [ T1] bus: 'i2c': add driver qixis_ctrl_i2c [ T1] i2c-core: driver [qixis_ctrl_i2c] registered [ T1] bus: 'fsl-mc': add driver fsl_mc_dpio [ T1] bus: 'platform': add driver dpaa2-console [ T1] bus: 'platform': add driver imx-pgc [ T1] bus: 'platform': add driver imx-gpcv2 [ T1] bus: 'platform': add driver imx9_init_soc [ T1] bus: 'platform': add driver imx_busfreq [ T1] Bus freq driver module loaded [ T1] bus: 'platform': add driver imx8m_pm_domain [ T1] bus: 'platform': add driver rpmsg-lifecycle [ T1] bus: 'platform': add driver imx8ulp-lpm [ T1] bus: 'platform': add driver imx93_power_domain [ T1] bus: 'platform': add driver imx93-blk-ctrl [ T1] bus: 'platform': add driver virtio-mmio [ T1] bus: 'virtio': add driver virtio_balloon [ T1] bus: 'platform': add driver axp20x-regulator [ T1] bus: 'platform': add driver bd718xx-pmic [ T1] bus: 'platform': add driver bd9571mwv-regulator [ T1] bus: 'i2c': add driver fan53555-regulator [ T1] i2c-core: driver [fan53555-regulator] registered [ T1] bus: 'platform': add driver hi6421v530-regulator [ T1] bus: 'platform': add driver max77620-pmic [ T1] bus: 'i2c': add driver mp8859 [ T1] i2c-core: driver [mp8859] registered [ T1] bus: 'platform': add driver mt6358-regulator [ T1] bus: 'platform': add driver mt6397-regulator [ T1] bus: 'platform': add driver qcom-spmi-regulator [ T1] bus: 'i2c': add driver nxp-pca9450 [ T1] i2c-core: driver [nxp-pca9450] registered [ T1] bus: 'i2c': add driver pf8x00 [ T1] i2c-core: driver [pf8x00] registered [ T1] bus: 'i2c': add driver pfuze100-regulator [ T1] i2c-core: driver [pfuze100-regulator] registered [ T1] bus: 'platform': add driver rk808-regulator [ T1] bus: 'platform': add driver s2mps11-pmic [ T1] bus: 'platform': add driver dispmix_reset_drv [ T1] bus: 'platform': add driver reset_imx7 [ T1] bus: 'platform': add driver reset_imx8ulp_sim [ T1] bus: 'scmi_protocol': add driver scmi-reset [ T1] device: 'ptyp0': device_add [ T1] PM: Adding info for No Bus:ptyp0 [ T1] device: 'ptyp1': device_add [ T1] PM: Adding info for No Bus:ptyp1 [ T1] device: 'ptyp2': device_add [ T1] PM: Adding info for No Bus:ptyp2 [ T1] device: 'ptyp3': device_add [ T1] PM: Adding info for No Bus:ptyp3 [ T1] device: 'ptyp4': device_add [ T1] PM: Adding info for No Bus:ptyp4 [ T1] device: 'ptyp5': device_add [ T1] PM: Adding info for No Bus:ptyp5 [ T1] device: 'ptyp6': device_add [ T1] PM: Adding info for No Bus:ptyp6 [ T1] device: 'ptyp7': device_add [ T1] PM: Adding info for No Bus:ptyp7 [ T1] device: 'ptyp8': device_add [ T1] PM: Adding info for No Bus:ptyp8 [ T1] device: 'ptyp9': device_add [ T1] PM: Adding info for No Bus:ptyp9 [ T1] device: 'ptypa': device_add [ T1] PM: Adding info for No Bus:ptypa [ T1] device: 'ptypb': device_add [ T1] PM: Adding info for No Bus:ptypb [ T1] device: 'ptypc': device_add [ T1] PM: Adding info for No Bus:ptypc [ T1] device: 'ptypd': device_add [ T1] PM: Adding info for No Bus:ptypd [ T1] device: 'ptype': device_add [ T1] PM: Adding info for No Bus:ptype [ T1] device: 'ptypf': device_add [ T1] PM: Adding info for No Bus:ptypf [ T1] device: 'ttyp0': device_add [ T1] PM: Adding info for No Bus:ttyp0 [ T1] device: 'ttyp1': device_add [ T1] PM: Adding info for No Bus:ttyp1 [ T1] device: 'ttyp2': device_add [ T1] PM: Adding info for No Bus:ttyp2 [ T1] device: 'ttyp3': device_add [ T1] PM: Adding info for No Bus:ttyp3 [ T1] device: 'ttyp4': device_add [ T1] PM: Adding info for No Bus:ttyp4 [ T1] device: 'ttyp5': device_add [ T1] PM: Adding info for No Bus:ttyp5 [ T1] device: 'ttyp6': device_add [ T1] PM: Adding info for No Bus:ttyp6 [ T1] device: 'ttyp7': device_add [ T1] PM: Adding info for No Bus:ttyp7 [ T1] device: 'ttyp8': device_add [ T1] PM: Adding info for No Bus:ttyp8 [ T1] device: 'ttyp9': device_add [ T1] PM: Adding info for No Bus:ttyp9 [ T1] device: 'ttypa': device_add [ T1] PM: Adding info for No Bus:ttypa [ T1] device: 'ttypb': device_add [ T1] PM: Adding info for No Bus:ttypb [ T1] device: 'ttypc': device_add [ T1] PM: Adding info for No Bus:ttypc [ T1] device: 'ttypd': device_add [ T1] PM: Adding info for No Bus:ttypd [ T1] device: 'ttype': device_add [ T1] PM: Adding info for No Bus:ttype [ T1] device: 'ttypf': device_add [ T1] PM: Adding info for No Bus:ttypf [ T1] device: 'ptmx': device_add [ T1] PM: Adding info for No Bus:ptmx [ T1] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ T1] bus: 'pnp': add driver serial [ T1] Registering platform device 'serial8250'. Parent at platform [ T1] device: 'serial8250': device_add [ T1] bus: 'platform': add device serial8250 [ T1] PM: Adding info for platform:serial8250 [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS0': device_add [ T1] PM: Adding info for No Bus:ttyS0 [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS1': device_add [ T1] PM: Adding info for No Bus:ttyS1 [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS2': device_add [ T1] PM: Adding info for No Bus:ttyS2 [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS3': device_add [ T1] PM: Adding info for No Bus:ttyS3 [ T1] bus: 'platform': add driver serial8250 [ T1] bus: 'platform': __driver_probe_device: matched device serial8250 with driver serial8250 [ T1] bus: 'platform': really_probe: probing driver serial8250 with device serial8250 [ T1] serial8250 serial8250: no default pinctrl state [ T1] driver: 'serial8250': driver_bound: bound to device 'serial8250' [ T1] devices_kset: Moving serial8250 to end of list [ T1] PM: Moving platform:serial8250 to end of list [ T1] devices_kset: Moving ttyS0 to end of list [ T1] PM: Moving No Bus:ttyS0 to end of list [ T1] devices_kset: Moving ttyS1 to end of list [ T1] PM: Moving No Bus:ttyS1 to end of list [ T1] devices_kset: Moving ttyS2 to end of list [ T1] PM: Moving No Bus:ttyS2 to end of list [ T1] devices_kset: Moving ttyS3 to end of list [ T1] PM: Moving No Bus:ttyS3 to end of list [ T1] bus: 'platform': really_probe: bound device serial8250 to driver serial8250 [ T1] bus: 'platform': add driver fsl-16550-uart [ T1] bus: 'platform': add driver dw-apb-uart [ T1] bus: 'platform': add driver of_serial [ T1] bus: 'platform': __driver_probe_device: matched device 21c0500.serial with driver of_serial [ T1] bus: 'platform': really_probe: probing driver of_serial with device 21c0500.serial [ T1] of_serial 21c0500.serial: no pinctrl handle [ T1] device: 'ttyS0': device_unregister [ T1] PM: Removing info for No Bus:ttyS0 [ T1] printk: console [ttyS0] disabled [ T1] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 44, base_baud = 25000000) is a 16550A [ T1] printk: console [ttyS0] enabled [ T1] printk: console [ttyS0] enabled [ T1] printk: bootconsole [uart8250] disabled [ T1] printk: bootconsole [uart8250] disabled [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS0': device_add [ T1] PM: Adding info for No Bus:ttyS0 [ T1] driver: 'of_serial': driver_bound: bound to device '21c0500.serial' [ T1] devices_kset: Moving 21c0500.serial to end of list [ T1] PM: Moving platform:21c0500.serial to end of list [ T1] devices_kset: Moving ttyS0 to end of list [ T1] PM: Moving No Bus:ttyS0 to end of list [ T1] bus: 'platform': really_probe: bound device 21c0500.serial to driver of_serial [ T1] bus: 'platform': __driver_probe_device: matched device 21c0600.serial with driver of_serial [ T1] bus: 'platform': really_probe: probing driver of_serial with device 21c0600.serial [ T1] of_serial 21c0600.serial: no pinctrl handle [ T1] device: 'ttyS1': device_unregister [ T1] PM: Removing info for No Bus:ttyS1 [ T1] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 44, base_baud = 25000000) is a 16550A [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS1': device_add [ T1] PM: Adding info for No Bus:ttyS1 [ T1] driver: 'of_serial': driver_bound: bound to device '21c0600.serial' [ T1] devices_kset: Moving 21c0600.serial to end of list [ T1] PM: Moving platform:21c0600.serial to end of list [ T1] devices_kset: Moving ttyS1 to end of list [ T1] PM: Moving No Bus:ttyS1 to end of list [ T1] bus: 'platform': really_probe: bound device 21c0600.serial to driver of_serial [ T1] bus: 'platform': __driver_probe_device: matched device 21d0500.serial with driver of_serial [ T1] bus: 'platform': really_probe: probing driver of_serial with device 21d0500.serial [ T1] of_serial 21d0500.serial: no pinctrl handle [ T1] device: 'ttyS2': device_unregister [ T1] PM: Removing info for No Bus:ttyS2 [ T1] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 45, base_baud = 25000000) is a 16550A [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS2': device_add [ T1] PM: Adding info for No Bus:ttyS2 [ T1] driver: 'of_serial': driver_bound: bound to device '21d0500.serial' [ T1] devices_kset: Moving 21d0500.serial to end of list [ T1] PM: Moving platform:21d0500.serial to end of list [ T1] devices_kset: Moving ttyS2 to end of list [ T1] PM: Moving No Bus:ttyS2 to end of list [ T1] bus: 'platform': really_probe: bound device 21d0500.serial to driver of_serial [ T1] bus: 'platform': __driver_probe_device: matched device 21d0600.serial with driver of_serial [ T1] bus: 'platform': really_probe: probing driver of_serial with device 21d0600.serial [ T1] of_serial 21d0600.serial: no pinctrl handle [ T1] device: 'ttyS3': device_unregister [ T1] PM: Removing info for No Bus:ttyS3 [ T1] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 45, base_baud = 25000000) is a 16550A [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyS3': device_add [ T1] PM: Adding info for No Bus:ttyS3 [ T1] driver: 'of_serial': driver_bound: bound to device '21d0600.serial' [ T1] devices_kset: Moving 21d0600.serial to end of list [ T1] PM: Moving platform:21d0600.serial to end of list [ T1] devices_kset: Moving ttyS3 to end of list [ T1] PM: Moving No Bus:ttyS3 to end of list [ T1] bus: 'platform': really_probe: bound device 21d0600.serial to driver of_serial [ T1] bus: 'platform': add driver imx-uart [ T1] bus: 'platform': add driver fsl-lpuart [ T1] bus: 'platform': __driver_probe_device: matched device 2970000.serial with driver fsl-lpuart [ T1] bus: 'platform': really_probe: probing driver fsl-lpuart with device 2970000.serial [ T1] fsl-lpuart 2970000.serial: no pinctrl handle [ T1] 2970000.serial: ttyLP2 at MMIO 0x2970000 (irq = 50, base_baud = 25000000) is a FSL_LPUART [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyLP2': device_add [ T1] PM: Adding info for No Bus:ttyLP2 [ T1] driver: 'fsl-lpuart': driver_bound: bound to device '2970000.serial' [ T1] devices_kset: Moving 2970000.serial to end of list [ T1] PM: Moving platform:2970000.serial to end of list [ T1] devices_kset: Moving ttyLP2 to end of list [ T1] PM: Moving No Bus:ttyLP2 to end of list [ T1] bus: 'platform': really_probe: bound device 2970000.serial to driver fsl-lpuart [ T1] bus: 'platform': __driver_probe_device: matched device 29a0000.serial with driver fsl-lpuart [ T1] bus: 'platform': really_probe: probing driver fsl-lpuart with device 29a0000.serial [ T1] fsl-lpuart 29a0000.serial: no pinctrl handle [ T1] 29a0000.serial: ttyLP5 at MMIO 0x29a0000 (irq = 51, base_baud = 25000000) is a FSL_LPUART [ T1] device: 'serial0': device_add [ T1] bus: 'serial': add device serial0 [ T1] PM: Adding info for serial:serial0 [ T1] bus: 'serial': remove device serial0 [ T1] PM: Removing info for serial:serial0 [ T1] device: 'ttyLP5': device_add [ T1] PM: Adding info for No Bus:ttyLP5 [ T1] driver: 'fsl-lpuart': driver_bound: bound to device '29a0000.serial' [ T1] devices_kset: Moving 29a0000.serial to end of list [ T1] PM: Moving platform:29a0000.serial to end of list [ T1] devices_kset: Moving ttyLP5 to end of list [ T1] PM: Moving No Bus:ttyLP5 to end of list [ T1] bus: 'platform': really_probe: bound device 29a0000.serial to driver fsl-lpuart [ T1] device class 'virtio-ports': registering [ T1] bus: 'virtio': add driver virtio_console [ T1] bus: 'virtio': add driver virtio_rproc_serial [ T1] device: 'hw_random': device_add [ T1] PM: Adding info for No Bus:hw_random [ T1] bus: 'tee': add driver optee-rng [ T1] bus: 'platform': add driver smccc_trng [ T1] bus: 'i2c': add driver tpm_i2c_infineon [ T1] i2c-core: driver [tpm_i2c_infineon] registered [ T1] bus: 'platform': add driver arm-smmu [ T1] bus: 'platform': add driver arm-smmu-v3 [ T15] device: 'cache': device_add [ T15] device: 'index0': device_add [ T15] device: 'index1': device_add [ T15] device: 'index2': device_add [ T16] device: 'cache': device_add [ T16] device: 'index0': device_add [ T16] device: 'index1': device_add [ T16] device: 'index2': device_add [ T21] device: 'cache': device_add [ T21] device: 'index0': device_add [ T21] device: 'index1': device_add [ T21] device: 'index2': device_add [ T26] device: 'cache': device_add [ T26] device: 'index0': device_add [ T26] device: 'index1': device_add [ T26] device: 'index2': device_add [ T1] device class 'devcoredump': registering [ T1] device: 'ram0': device_add [ T1] PM: Adding info for No Bus:ram0 [ T1] device: '1:0': device_add [ T1] PM: Adding info for No Bus:1:0 [ T1] device: 'ram1': device_add [ T1] PM: Adding info for No Bus:ram1 [ T1] device: '1:1': device_add [ T1] PM: Adding info for No Bus:1:1 [ T1] device: 'ram2': device_add [ T1] PM: Adding info for No Bus:ram2 [ T1] device: '1:2': device_add [ T1] PM: Adding info for No Bus:1:2 [ T1] device: 'ram3': device_add [ T1] PM: Adding info for No Bus:ram3 [ T1] device: '1:3': device_add [ T1] PM: Adding info for No Bus:1:3 [ T1] device: 'ram4': device_add [ T1] PM: Adding info for No Bus:ram4 [ T1] device: '1:4': device_add [ T1] PM: Adding info for No Bus:1:4 [ T1] device: 'ram5': device_add [ T1] PM: Adding info for No Bus:ram5 [ T1] device: '1:5': device_add [ T1] PM: Adding info for No Bus:1:5 [ T1] device: 'ram6': device_add [ T1] PM: Adding info for No Bus:ram6 [ T1] device: '1:6': device_add [ T1] PM: Adding info for No Bus:1:6 [ T1] device: 'ram7': device_add [ T1] PM: Adding info for No Bus:ram7 [ T1] device: '1:7': device_add [ T1] PM: Adding info for No Bus:1:7 [ T1] device: 'ram8': device_add [ T1] PM: Adding info for No Bus:ram8 [ T1] device: '1:8': device_add [ T1] PM: Adding info for No Bus:1:8 [ T1] device: 'ram9': device_add [ T1] PM: Adding info for No Bus:ram9 [ T1] device: '1:9': device_add [ T1] PM: Adding info for No Bus:1:9 [ T1] device: 'ram10': device_add [ T1] PM: Adding info for No Bus:ram10 [ T1] device: '1:10': device_add [ T1] PM: Adding info for No Bus:1:10 [ T1] device: 'ram11': device_add [ T1] PM: Adding info for No Bus:ram11 [ T1] device: '1:11': device_add [ T1] PM: Adding info for No Bus:1:11 [ T1] device: 'ram12': device_add [ T1] PM: Adding info for No Bus:ram12 [ T1] device: '1:12': device_add [ T1] PM: Adding info for No Bus:1:12 [ T1] device: 'ram13': device_add [ T1] PM: Adding info for No Bus:ram13 [ T1] device: '1:13': device_add [ T1] PM: Adding info for No Bus:1:13 [ T1] device: 'ram14': device_add [ T1] PM: Adding info for No Bus:ram14 [ T1] device: '1:14': device_add [ T1] PM: Adding info for No Bus:1:14 [ T1] device: 'ram15': device_add [ T1] PM: Adding info for No Bus:ram15 [ T1] device: '1:15': device_add [ T1] PM: Adding info for No Bus:1:15 [ T1] brd: module loaded [ T1] device: 'loop-control': device_add [ T1] PM: Adding info for No Bus:loop-control [ T1] device: 'loop0': device_add [ T1] PM: Adding info for No Bus:loop0 [ T1] device: '7:0': device_add [ T1] PM: Adding info for No Bus:7:0 [ T1] device: 'loop1': device_add [ T1] PM: Adding info for No Bus:loop1 [ T1] device: '7:1': device_add [ T1] PM: Adding info for No Bus:7:1 [ T1] device: 'loop2': device_add [ T1] PM: Adding info for No Bus:loop2 [ T1] device: '7:2': device_add [ T1] PM: Adding info for No Bus:7:2 [ T1] device: 'loop3': device_add [ T1] PM: Adding info for No Bus:loop3 [ T1] device: '7:3': device_add [ T1] PM: Adding info for No Bus:7:3 [ T1] device: 'loop4': device_add [ T1] PM: Adding info for No Bus:loop4 [ T1] device: '7:4': device_add [ T1] PM: Adding info for No Bus:7:4 [ T1] device: 'loop5': device_add [ T1] PM: Adding info for No Bus:loop5 [ T1] device: '7:5': device_add [ T1] PM: Adding info for No Bus:7:5 [ T1] device: 'loop6': device_add [ T1] PM: Adding info for No Bus:loop6 [ T1] device: '7:6': device_add [ T1] PM: Adding info for No Bus:7:6 [ T1] device: 'loop7': device_add [ T1] PM: Adding info for No Bus:loop7 [ T1] device: '7:7': device_add [ T1] PM: Adding info for No Bus:7:7 [ T1] loop: module loaded [ T1] bus: 'virtio': add driver virtio_blk [ T1] bus: 'i2c': add driver at24 [ T1] bus: 'i2c': __driver_probe_device: matched device 0-0050 with driver at24 [ T1] bus: 'i2c': really_probe: probing driver at24 with device 0-0050 [ T1] at24 0-0050: no pinctrl handle [ T1] at24 0-0050: probe [ T1] at24_probe [ T1] at24_get_chip_data [ T1] at24_get_chip_data1 [ T1] at24 0-0050: supply vcc not found, using dummy regulator [ T1] device: 'regulator:regulator.0--i2c:0-0050': device_add [ T1] devices_kset: Moving 0-0050 to end of list [ T1] PM: Moving i2c:0-0050 to end of list [ T1] at24 0-0050: Linked as a consumer to regulator.0 [ T1] device: '0-0051': device_add [ T1] bus: 'i2c': add device 0-0051 [ T1] PM: Adding info for i2c:0-0051 [ T1] bus: 'i2c': __driver_probe_device: matched device 0-0051 with driver dummy [ T1] bus: 'i2c': really_probe: probing driver dummy with device 0-0051 [ T1] dummy 0-0051: no default pinctrl state [ T1] dummy 0-0051: probe [ T1] driver: 'dummy': driver_bound: bound to device '0-0051' [ T1] devices_kset: Moving 0-0051 to end of list [ T1] PM: Moving i2c:0-0051 to end of list [ T1] bus: 'i2c': really_probe: bound device 0-0051 to driver dummy [ T1] i2c i2c-0: client [dummy] registered with bus id 0-0051 [ T1] device: '0-00500': device_add [ T1] bus: 'nvmem': add device 0-00500 [ T1] PM: Adding info for nvmem:0-00500 [ T1] at24_read [ T1] at24_base_client_dev [ T1] at24_regmap_read [ T1] at24_translate_offset offset 0X0 [ T1] at24_adjust_read_count [ T1] i2c i2c-0: transfer message: 0 [ T1] i2c i2c-0: CONTROL: IEN=0, IIEN=1, MSTA=1, MTX=1, TXAK=1, RSTA=0 [ T1] i2c i2c-0: STATUS: ICF=1, IAAS=0, IBB=1, IAL=0, SRW=0, IIF=0, RXAK=0 [ T1] i2c i2c-0: write slave address: addr=0xa0 [ T1] i2c i2c-0: TRX complete [ T1] i2c i2c-0: ACK received [ T1] i2c i2c-0: write data [ T1] i2c i2c-0: write byte: B0=0x0 [ T1] i2c i2c-0: TRX complete [ T1] i2c i2c-0: ACK received [ T1] i2c i2c-0: write byte: B1=0x0 [ T1] i2c i2c-0: TRX complete [ T1] i2c i2c-0: ACK received [ T1] i2c i2c-0: repeated start [ T1] i2c i2c-0: transfer message: 1 [ T1] i2c i2c-0: CONTROL: IEN=0, IIEN=1, MSTA=1, MTX=1, TXAK=1, RSTA=0 [ T1] i2c i2c-0: STATUS: ICF=1, IAAS=0, IBB=1, IAL=0, SRW=0, IIF=0, RXAK=0 [ T1] i2c i2c-0: write slave address: addr=0xa1 [ T1] i2c i2c-0: TRX complete [ T1] i2c i2c-0: ACK received [ T1] i2c i2c-0: setup bus [ T1] i2c i2c-0: read data [ T1] i2c i2c-0: TRX complete [ T1] i2c i2c-0: clear MSTA [ T1] i2c i2c-0: read byte: B0=0x0 [ T1] i2c i2c-0: exit with: success msg: 2 [ T1] at24 0-0050: 131072 byte at24cm01 EEPROM, writable, 128 bytes/write [ T1] driver: 'at24': driver_bound: bound to device '0-0050' [ T1] devices_kset: Moving 0-0050 to end of list [ T1] PM: Moving i2c:0-0050 to end of list [ T1] devices_kset: Moving 0-00500 to end of list [ T1] PM: Moving nvmem:0-00500 to end of list [ T1] bus: 'i2c': really_probe: bound device 0-0050 to driver at24 [ T1] i2c-core: driver [at24] registered [ T1] bus: 'i2c': add driver eeprom [ T1] i2c-core: driver [eeprom] registered [ T1] bus: 'i2c': add driver bd9571mwv [ T1] i2c-core: driver [bd9571mwv] registered [ T1] bus: 'platform': add driver imx-mix [ T1] bus: 'i2c': add driver axp20x-i2c [ T1] i2c-core: driver [axp20x-i2c] registered [ T1] bus: 'i2c': add driver max77620 [ T1] i2c-core: driver [max77620] registered [ T1] bus: 'i2c': add driver rk808 [ T1] i2c-core: driver [rk808] registered [ T1] bus: 'i2c': add driver sec_pmic [ T1] i2c-core: driver [sec_pmic] registered [ T1] bus: 'platform': add driver hi6421_pmic [ T1] bus: 'platform': add driver mt6397 [ T1] bus: 'i2c': add driver simple-mfd-i2c [ T1] i2c-core: driver [simple-mfd-i2c] registered [ T1] device class 'mtd': registering [ T1] device: 'mtd-0': device_add [ T1] PM: Adding info for No Bus:mtd-0 [ T1] bus: 'platform': add driver physmap-flash [ T1] bus: 'spi': add driver mtd_dataflash [ T1] bus: 'spi': add driver sst25l [ T1] bus: 'spi': add driver spi-nor [ T1] device class 'spidev': registering [ T1] bus: 'spi': add driver spidev [ T1] bus: 'platform': add driver fsl-dspi [ T1] bus: 'platform': __driver_probe_device: matched device 2100000.spi with driver fsl-dspi [ T1] bus: 'platform': really_probe: probing driver fsl-dspi with device 2100000.spi [ T1] fsl-dspi 2100000.spi: no pinctrl handle [ T1] device: 'spi0': device_add [ T1] PM: Adding info for No Bus:spi0 [ T1] fsl-dspi 2100000.spi: registered master spi0 [ T1] driver: 'fsl-dspi': driver_bound: bound to device '2100000.spi' [ T1] devices_kset: Moving 2100000.spi to end of list [ T1] PM: Moving platform:2100000.spi to end of list [ T1] devices_kset: Moving spi0 to end of list [ T1] PM: Moving No Bus:spi0 to end of list [ T1] bus: 'platform': really_probe: bound device 2100000.spi to driver fsl-dspi [ T1] bus: 'platform': add driver nxp-fspi [ T1] device class 'macvtap': registering [ T1] bus: 'platform': add driver sfp [ T1] bus: 'mdio_bus': add driver ADIN1200 [ T1] bus: 'mdio_bus': add driver ADIN1300 [ T1] Registering platform device 'Fixed MDIO bus.0'. Parent at platform [ T1] device: 'Fixed MDIO bus.0': device_add [ T1] bus: 'platform': add device Fixed MDIO bus.0 [ T1] PM: Adding info for platform:Fixed MDIO bus.0 [ T1] device: 'fixed-0': device_add [ T1] PM: Adding info for No Bus:fixed-0 [ T1] bus: 'mdio_bus': add driver RTL8201CP Ethernet [ T1] bus: 'mdio_bus': add driver RTL8201F Fast Ethernet [ T1] bus: 'mdio_bus': add driver RTL8208 Fast Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211 Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211B Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211C Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211DN Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211E Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211F Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL8211F-VD Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver Generic FE-GE Realtek PHY [ T1] bus: 'mdio_bus': add driver RTL8226 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8226B_RTL8221B 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8226-CG 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8221B-VB-CG 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8221B-VM-CG 2.5Gbps PHY [ T1] bus: 'mdio_bus': add driver RTL8366RB Gigabit Ethernet [ T1] bus: 'mdio_bus': add driver RTL9000AA_RTL9000AN Ethernet [ T1] bus: 'mdio_bus': add driver RTL8365MB-VC Gigabit Ethernet [ T1] bus: 'platform': add driver mdio-mux-mmioreg [ T1] bus: 'platform': add driver mdio-mux-multiplexer [ T1] tun: Universal TUN/TAP device driver, 1.6 [ T1] device: 'tun': device_add [ T1] PM: Adding info for No Bus:tun [ T1] bus: 'virtio': add driver virtio_net [ T1] bus: 'platform': add driver fec [ T1] bus: 'platform': add driver fsl-fman_xmdio [ T1] bus: 'platform': __driver_probe_device: matched device 1afc000.mdio with driver fsl-fman_xmdio [ T1] bus: 'platform': really_probe: probing driver fsl-fman_xmdio with device 1afc000.mdio [ T1] fsl-fman_xmdio 1afc000.mdio: no pinctrl handle [ T1] device: '0x0000000001afc000': device_add [ T1] PM: Adding info for No Bus:0x0000000001afc000 [ T1] device: '0x0000000001afc000:08': device_add [ T1] bus: 'mdio_bus': add device 0x0000000001afc000:08 [ T1] PM: Adding info for mdio_bus:0x0000000001afc000:08 [ T1] bus: 'mdio_bus': __driver_probe_device: matched device 0x0000000001afc000:08 with driver ADIN1300 [ T1] bus: 'mdio_bus': really_probe: probing driver ADIN1300 with device 0x0000000001afc000:08 [ T1] ADIN1300 0x0000000001afc000:08: no pinctrl handle [ T1] adin_probe [ T1] driver: 'ADIN1300': driver_bound: bound to device '0x0000000001afc000:08' [ T1] devices_kset: Moving 0x0000000001afc000:08 to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:08 to end of list [ T1] bus: 'mdio_bus': really_probe: bound device 0x0000000001afc000:08 to driver ADIN1300 [ T1] device: '0x0000000001afc000:0c': device_add [ T1] bus: 'mdio_bus': add device 0x0000000001afc000:0c [ T1] PM: Adding info for mdio_bus:0x0000000001afc000:0c [ T1] bus: 'mdio_bus': __driver_probe_device: matched device 0x0000000001afc000:0c with driver ADIN1300 [ T1] bus: 'mdio_bus': really_probe: probing driver ADIN1300 with device 0x0000000001afc000:0c [ T1] ADIN1300 0x0000000001afc000:0c: no pinctrl handle [ T1] adin_probe [ T1] driver: 'ADIN1300': driver_bound: bound to device '0x0000000001afc000:0c' [ T1] devices_kset: Moving 0x0000000001afc000:0c to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:0c to end of list [ T1] bus: 'mdio_bus': really_probe: bound device 0x0000000001afc000:0c to driver ADIN1300 [ T1] driver: 'fsl-fman_xmdio': driver_bound: bound to device '1afc000.mdio' [ T1] devices_kset: Moving 1afc000.mdio to end of list [ T1] PM: Moving platform:1afc000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001afc000 to end of list [ T1] PM: Moving No Bus:0x0000000001afc000 to end of list [ T1] devices_kset: Moving 0x0000000001afc000:08 to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:08 to end of list [ T1] devices_kset: Moving 0x0000000001afc000:0c to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:0c to end of list [ T1] bus: 'platform': really_probe: bound device 1afc000.mdio to driver fsl-fman_xmdio [ T1] bus: 'platform': __driver_probe_device: matched device 1afd000.mdio with driver fsl-fman_xmdio [ T1] bus: 'platform': really_probe: probing driver fsl-fman_xmdio with device 1afd000.mdio [ T1] fsl-fman_xmdio 1afd000.mdio: no pinctrl handle [ T1] device: '0x0000000001afd000': device_add [ T1] PM: Adding info for No Bus:0x0000000001afd000 [ T1] driver: 'fsl-fman_xmdio': driver_bound: bound to device '1afd000.mdio' [ T1] devices_kset: Moving 1afd000.mdio to end of list [ T1] PM: Moving platform:1afd000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001afd000 to end of list [ T1] PM: Moving No Bus:0x0000000001afd000 to end of list [ T1] bus: 'platform': really_probe: bound device 1afd000.mdio to driver fsl-fman_xmdio [ T1] bus: 'platform': __driver_probe_device: matched device 1ae5000.mdio with driver fsl-fman_xmdio [ T1] bus: 'platform': really_probe: probing driver fsl-fman_xmdio with device 1ae5000.mdio [ T1] fsl-fman_xmdio 1ae5000.mdio: no pinctrl handle [ T1] device: '0x0000000001ae5000': device_add [ T1] PM: Adding info for No Bus:0x0000000001ae5000 [ T1] device: '0x0000000001ae5000:00': device_add [ T1] bus: 'mdio_bus': add device 0x0000000001ae5000:00 [ T1] PM: Adding info for mdio_bus:0x0000000001ae5000:00 [ T1] driver: 'fsl-fman_xmdio': driver_bound: bound to device '1ae5000.mdio' [ T1] devices_kset: Moving 1ae5000.mdio to end of list [ T1] PM: Moving platform:1ae5000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001ae5000 to end of list [ T1] PM: Moving No Bus:0x0000000001ae5000 to end of list [ T1] devices_kset: Moving 0x0000000001ae5000:00 to end of list [ T1] PM: Moving mdio_bus:0x0000000001ae5000:00 to end of list [ T1] bus: 'platform': really_probe: bound device 1ae5000.mdio to driver fsl-fman_xmdio [ T1] bus: 'platform': __driver_probe_device: matched device 1ae7000.mdio with driver fsl-fman_xmdio [ T1] bus: 'platform': really_probe: probing driver fsl-fman_xmdio with device 1ae7000.mdio [ T1] fsl-fman_xmdio 1ae7000.mdio: no pinctrl handle [ T1] device: '0x0000000001ae7000': device_add [ T1] PM: Adding info for No Bus:0x0000000001ae7000 [ T1] device: '0x0000000001ae7000:00': device_add [ T1] bus: 'mdio_bus': add device 0x0000000001ae7000:00 [ T1] PM: Adding info for mdio_bus:0x0000000001ae7000:00 [ T1] driver: 'fsl-fman_xmdio': driver_bound: bound to device '1ae7000.mdio' [ T1] devices_kset: Moving 1ae7000.mdio to end of list [ T1] PM: Moving platform:1ae7000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001ae7000 to end of list [ T1] PM: Moving No Bus:0x0000000001ae7000 to end of list [ T1] devices_kset: Moving 0x0000000001ae7000:00 to end of list [ T1] PM: Moving mdio_bus:0x0000000001ae7000:00 to end of list [ T1] bus: 'platform': really_probe: bound device 1ae7000.mdio to driver fsl-fman_xmdio [ T1] bus: 'platform': add driver fsl-fman [ T1] bus: 'platform': __driver_probe_device: matched device 1a00000.fman with driver fsl-fman [ T1] bus: 'platform': really_probe: probing driver fsl-fman with device 1a00000.fman [ T1] fsl-fman 1a00000.fman: no pinctrl handle [ T1] device class 'fm0': registering [ T1] device: 'fm0': device_add [ T1] PM: Adding info for No Bus:fm0 [ T1] device: 'fm0-pcd': device_add [ T1] PM: Adding info for No Bus:fm0-pcd [ T1] driver: 'fsl-fman': driver_bound: bound to device '1a00000.fman' [ T1] devices_kset: Moving 1a00000.fman to end of list [ T1] PM: Moving platform:1a00000.fman to end of list [ T1] devices_kset: Moving 1a00000.fman:fman-firmware to end of list [ T1] PM: Moving platform:1a00000.fman:fman-firmware to end of list [ T1] devices_kset: Moving 1a00000.fman:cc to end of list [ T1] PM: Moving platform:1a00000.fman:cc to end of list [ T1] devices_kset: Moving 1a00000.muram to end of list [ T1] PM: Moving platform:1a00000.muram to end of list [ T1] devices_kset: Moving 1a80000.bmi to end of list [ T1] PM: Moving platform:1a80000.bmi to end of list [ T1] devices_kset: Moving 1a80400.qmi to end of list [ T1] PM: Moving platform:1a80400.qmi to end of list [ T1] devices_kset: Moving 1a82000.port to end of list [ T1] PM: Moving platform:1a82000.port to end of list [ T1] devices_kset: Moving 1a83000.port to end of list [ T1] PM: Moving platform:1a83000.port to end of list [ T1] devices_kset: Moving 1a84000.port to end of list [ T1] PM: Moving platform:1a84000.port to end of list [ T1] devices_kset: Moving 1a85000.port to end of list [ T1] PM: Moving platform:1a85000.port to end of list [ T1] devices_kset: Moving 1a86000.port to end of list [ T1] PM: Moving platform:1a86000.port to end of list [ T1] devices_kset: Moving 1a87000.port to end of list [ T1] PM: Moving platform:1a87000.port to end of list [ T1] devices_kset: Moving 1ac0000.policer to end of list [ T1] PM: Moving platform:1ac0000.policer to end of list [ T1] devices_kset: Moving 1ac1000.keygen to end of list [ T1] PM: Moving platform:1ac1000.keygen to end of list [ T1] devices_kset: Moving 1ac2000.dma to end of list [ T1] PM: Moving platform:1ac2000.dma to end of list [ T1] devices_kset: Moving 1ac3000.fpm to end of list [ T1] PM: Moving platform:1ac3000.fpm to end of list [ T1] devices_kset: Moving 1ac7000.parser to end of list [ T1] PM: Moving platform:1ac7000.parser to end of list [ T1] devices_kset: Moving 1adc000.vsps to end of list [ T1] PM: Moving platform:1adc000.vsps to end of list [ T1] devices_kset: Moving 1afc000.mdio to end of list [ T1] PM: Moving platform:1afc000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001afc000 to end of list [ T1] PM: Moving No Bus:0x0000000001afc000 to end of list [ T1] devices_kset: Moving 0x0000000001afc000:08 to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:08 to end of list [ T1] devices_kset: Moving 0x0000000001afc000:0c to end of list [ T1] PM: Moving mdio_bus:0x0000000001afc000:0c to end of list [ T1] devices_kset: Moving 1afd000.mdio to end of list [ T1] PM: Moving platform:1afd000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001afd000 to end of list [ T1] PM: Moving No Bus:0x0000000001afd000 to end of list [ T1] devices_kset: Moving 1a8a000.port to end of list [ T1] PM: Moving platform:1a8a000.port to end of list [ T1] devices_kset: Moving 1aaa000.port to end of list [ T1] PM: Moving platform:1aaa000.port to end of list [ T1] devices_kset: Moving 1ae4000.ethernet to end of list [ T1] PM: Moving platform:1ae4000.ethernet to end of list [ T1] devices_kset: Moving 1ae5000.mdio to end of list [ T1] PM: Moving platform:1ae5000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001ae5000 to end of list [ T1] PM: Moving No Bus:0x0000000001ae5000 to end of list [ T1] devices_kset: Moving 0x0000000001ae5000:00 to end of list [ T1] PM: Moving mdio_bus:0x0000000001ae5000:00 to end of list [ T1] devices_kset: Moving 1a8b000.port to end of list [ T1] PM: Moving platform:1a8b000.port to end of list [ T1] devices_kset: Moving 1aab000.port to end of list [ T1] PM: Moving platform:1aab000.port to end of list [ T1] devices_kset: Moving 1ae6000.ethernet to end of list [ T1] PM: Moving platform:1ae6000.ethernet to end of list [ T1] devices_kset: Moving 1ae7000.mdio to end of list [ T1] PM: Moving platform:1ae7000.mdio to end of list [ T1] devices_kset: Moving 0x0000000001ae7000 to end of list [ T1] PM: Moving No Bus:0x0000000001ae7000 to end of list [ T1] devices_kset: Moving 0x0000000001ae7000:00 to end of list [ T1] PM: Moving mdio_bus:0x0000000001ae7000:00 to end of list [ T1] bus: 'platform': really_probe: bound device 1a00000.fman to driver fsl-fman [ T1] Freescale FM module, FMD API version 21.1.0 [ T1] bus: 'platform': add driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a82000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a82000.port [ T1] fsl-fman-port 1a82000.port: no pinctrl handle [ T1] device: 'fm0-port-oh0': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh0 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a82000.port' [ T1] devices_kset: Moving 1a82000.port to end of list [ T1] PM: Moving platform:1a82000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a82000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a83000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a83000.port [ T1] fsl-fman-port 1a83000.port: no pinctrl handle [ T1] device: 'fm0-port-oh1': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh1 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a83000.port' [ T1] devices_kset: Moving 1a83000.port to end of list [ T1] PM: Moving platform:1a83000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a83000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a84000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a84000.port [ T1] fsl-fman-port 1a84000.port: no pinctrl handle [ T1] device: 'fm0-port-oh2': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh2 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a84000.port' [ T1] devices_kset: Moving 1a84000.port to end of list [ T1] PM: Moving platform:1a84000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a84000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a85000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a85000.port [ T1] fsl-fman-port 1a85000.port: no pinctrl handle [ T1] device: 'fm0-port-oh3': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh3 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a85000.port' [ T1] devices_kset: Moving 1a85000.port to end of list [ T1] PM: Moving platform:1a85000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a85000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a86000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a86000.port [ T1] fsl-fman-port 1a86000.port: no pinctrl handle [ T1] device: 'fm0-port-oh4': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh4 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a86000.port' [ T1] devices_kset: Moving 1a86000.port to end of list [ T1] PM: Moving platform:1a86000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a86000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a87000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a87000.port [ T1] fsl-fman-port 1a87000.port: no pinctrl handle [ T1] device: 'fm0-port-oh5': device_add [ T1] PM: Adding info for No Bus:fm0-port-oh5 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a87000.port' [ T1] devices_kset: Moving 1a87000.port to end of list [ T1] PM: Moving platform:1a87000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a87000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a8a000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a8a000.port [ T1] fsl-fman-port 1a8a000.port: no pinctrl handle [ T1] device: 'fm0-port-rx2': device_add [ T1] PM: Adding info for No Bus:fm0-port-rx2 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a8a000.port' [ T1] devices_kset: Moving 1a8a000.port to end of list [ T1] PM: Moving platform:1a8a000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a8a000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1aaa000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1aaa000.port [ T1] fsl-fman-port 1aaa000.port: no pinctrl handle [ T1] device: 'fm0-port-tx2': device_add [ T1] PM: Adding info for No Bus:fm0-port-tx2 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1aaa000.port' [ T1] devices_kset: Moving 1aaa000.port to end of list [ T1] PM: Moving platform:1aaa000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1aaa000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1a8b000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1a8b000.port [ T1] fsl-fman-port 1a8b000.port: no pinctrl handle [ T1] device: 'fm0-port-rx3': device_add [ T1] PM: Adding info for No Bus:fm0-port-rx3 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1a8b000.port' [ T1] devices_kset: Moving 1a8b000.port to end of list [ T1] PM: Moving platform:1a8b000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1a8b000.port to driver fsl-fman-port [ T1] bus: 'platform': __driver_probe_device: matched device 1aab000.port with driver fsl-fman-port [ T1] bus: 'platform': really_probe: probing driver fsl-fman-port with device 1aab000.port [ T1] fsl-fman-port 1aab000.port: no pinctrl handle [ T1] device: 'fm0-port-tx3': device_add [ T1] PM: Adding info for No Bus:fm0-port-tx3 [ T1] driver: 'fsl-fman-port': driver_bound: bound to device '1aab000.port' [ T1] devices_kset: Moving 1aab000.port to end of list [ T1] PM: Moving platform:1aab000.port to end of list [ T1] bus: 'platform': really_probe: bound device 1aab000.port to driver fsl-fman-port [ T1] Freescale FM Ports module [ T1] fsl_mac: fsl_mac: FSL FMan MAC API based driver [ T1] bus: 'platform': add driver fsl_mac [ T1] bus: 'platform': __driver_probe_device: matched device 1ae4000.ethernet with driver fsl_mac [ T1] bus: 'platform': really_probe: probing driver fsl_mac with device 1ae4000.ethernet [ T1] fsl_mac 1ae4000.ethernet: no pinctrl handle [ T1] fsl_mac 1ae4000.ethernet: FMan MEMAC [ T1] fsl_mac 1ae4000.ethernet: FMan MAC address: 00:04:9f:07:5c:a7 [ T1] driver: 'fsl_mac': driver_bound: bound to device '1ae4000.ethernet' [ T1] devices_kset: Moving 1ae4000.ethernet to end of list [ T1] PM: Moving platform:1ae4000.ethernet to end of list [ T1] bus: 'platform': really_probe: bound device 1ae4000.ethernet to driver fsl_mac [ T1] bus: 'platform': __driver_probe_device: matched device 1ae6000.ethernet with driver fsl_mac [ T1] bus: 'platform': really_probe: probing driver fsl_mac with device 1ae6000.ethernet [ T1] fsl_mac 1ae6000.ethernet: no pinctrl handle [ T1] fsl_mac 1ae6000.ethernet: of_get_mac_address(ethernet@e6000) failed [ T1] fsl_mac: probe of 1ae6000.ethernet failed with error -22 [ T1] fsl_dpa: FSL DPAA Ethernet driver [ T1] bus: 'platform': add driver fsl_dpa [ T1] bus: 'platform': __driver_probe_device: matched device soc:fsl,dpaa:ethernet@2 with driver fsl_dpa [ T1] bus: 'platform': really_probe: probing driver fsl_dpa with device soc:fsl,dpaa:ethernet@2 [ T1] fsl_dpa soc:fsl,dpaa:ethernet@2: no pinctrl handle [ T1] fsl_dpa soc:fsl,dpaa:ethernet@2: Skip RX PCD High Priority FQs initialization [ T1] device: 'eth0': device_add [ T1] PM: Adding info for No Bus:eth0 [ T1] fsl_dpa: fsl_dpa: Probed interface eth0 [ T1] driver: 'fsl_dpa': driver_bound: bound to device 'soc:fsl,dpaa:ethernet@2' [ T1] devices_kset: Moving soc:fsl,dpaa:ethernet@2 to end of list [ T1] PM: Moving platform:soc:fsl,dpaa:ethernet@2 to end of list [ T1] devices_kset: Moving eth0 to end of list [ T1] PM: Moving No Bus:eth0 to end of list [ T1] bus: 'platform': really_probe: bound device soc:fsl,dpaa:ethernet@2 to driver fsl_dpa [ T1] bus: 'platform': __driver_probe_device: matched device soc:fsl,dpaa:ethernet@3 with driver fsl_dpa [ T1] bus: 'platform': really_probe: probing driver fsl_dpa with device soc:fsl,dpaa:ethernet@3 [ T1] fsl_dpa soc:fsl,dpaa:ethernet@3: no pinctrl handle [ T1] fsl_dpa soc:fsl,dpaa:ethernet@3: dev_get_drvdata(1ae6000.ethernet) failed [ T1] fsl_dpa: probe of soc:fsl,dpaa:ethernet@3 failed with error -22 [ T1] fsl_advanced: FSL DPAA Advanced drivers: [ T1] fsl_proxy: FSL DPAA Proxy initialization driver [ T1] bus: 'platform': add driver fsl_proxy-proxy [ T1] fsl_oh: FSL FMan Offline Parsing port driver [ T1] bus: 'platform': add driver fsl_oh [ T1] bus: 'fsl-mc': add driver fsl_dpaa2_eth [ T1] bus: 'fsl-mc': add driver fsl_dpaa2_ptp [ T1] bus: 'fsl-mc': add driver fsl_dpaa2_switch [ T1] bus: 'fsl-mc': add driver fsl_dpaa2_mac [ T1] bus: 'platform': add driver fsl-enetc-ierb [ T1] device class 'uio': registering [ T1] bus: 'platform': add driver uio_pdrv_genirq [ T1] bus: 'platform': add driver uio_dmem_genirq [ T1] bus: 'i2c': add driver rtc-ds3232 [ T1] bus: 'i2c': __driver_probe_device: matched device 1-0068 with driver rtc-ds3232 [ T1] bus: 'i2c': really_probe: probing driver rtc-ds3232 with device 1-0068 [ T1] rtc-ds3232 1-0068: no pinctrl handle [ T1] rtc-ds3232 1-0068: probe [ T1] i2c i2c-1: exit with: error: -11 [ T1] rtc-ds3232: probe of 1-0068 failed with error -11 [ T1] i2c-core: driver [rtc-ds3232] registered [ T1] bus: 'spi': add driver ds3234 [ T1] bus: 'platform': add driver rtc-test [ T1] Registering platform device 'rtc-test.0'. Parent at platform [ T1] device: 'rtc-test.0': device_add [ T1] bus: 'platform': add device rtc-test.0 [ T1] PM: Adding info for platform:rtc-test.0 [ T1] bus: 'platform': __driver_probe_device: matched device rtc-test.0 with driver rtc-test [ T1] bus: 'platform': really_probe: probing driver rtc-test with device rtc-test.0 [ T1] rtc-test rtc-test.0: no default pinctrl state [ T1] device: 'rtc0': device_add [ T1] PM: Adding info for No Bus:rtc0 [ T1] rtc-test rtc-test.0: char device (252:0) [ T1] rtc-test rtc-test.0: registered as rtc0 [ T1] rtc-test rtc-test.0: setting system clock to 1970-01-01T00:00:10 UTC (10) [ T1] driver: 'rtc-test': driver_bound: bound to device 'rtc-test.0' [ T1] devices_kset: Moving rtc-test.0 to end of list [ T1] PM: Moving platform:rtc-test.0 to end of list [ T1] devices_kset: Moving rtc0 to end of list [ T1] PM: Moving No Bus:rtc0 to end of list [ T1] bus: 'platform': really_probe: bound device rtc-test.0 to driver rtc-test [ T1] Registering platform device 'rtc-test.1'. Parent at platform [ T1] device: 'rtc-test.1': device_add [ T1] bus: 'platform': add device rtc-test.1 [ T1] PM: Adding info for platform:rtc-test.1 [ T1] bus: 'platform': __driver_probe_device: matched device rtc-test.1 with driver rtc-test [ T1] bus: 'platform': really_probe: probing driver rtc-test with device rtc-test.1 [ T1] rtc-test rtc-test.1: no default pinctrl state [ T1] device: 'wakeup0': device_add [ T1] device: 'rtc1': device_add [ T1] PM: Adding info for No Bus:rtc1 [ T1] Registering platform device 'alarmtimer.0.auto'. Parent at rtc1 [ T1] device: 'alarmtimer.0.auto': device_add [ T1] bus: 'platform': add device alarmtimer.0.auto [ T1] PM: Adding info for platform:alarmtimer.0.auto [ T1] bus: 'platform': __driver_probe_device: matched device alarmtimer.0.auto with driver alarmtimer [ T1] bus: 'platform': really_probe: probing driver alarmtimer with device alarmtimer.0.auto [ T1] alarmtimer alarmtimer.0.auto: no default pinctrl state [ T1] driver: 'alarmtimer': driver_bound: bound to device 'alarmtimer.0.auto' [ T1] devices_kset: Moving alarmtimer.0.auto to end of list [ T1] PM: Moving platform:alarmtimer.0.auto to end of list [ T1] bus: 'platform': really_probe: bound device alarmtimer.0.auto to driver alarmtimer [ T1] device: 'wakeup1': device_add [ T1] rtc-test rtc-test.1: char device (252:1) [ T1] rtc-test rtc-test.1: registered as rtc1 [ T1] driver: 'rtc-test': driver_bound: bound to device 'rtc-test.1' [ T1] devices_kset: Moving rtc-test.1 to end of list [ T1] PM: Moving platform:rtc-test.1 to end of list [ T1] devices_kset: Moving wakeup0 to end of list [ T1] devices_kset: Moving rtc1 to end of list [ T1] PM: Moving No Bus:rtc1 to end of list [ T1] devices_kset: Moving alarmtimer.0.auto to end of list [ T1] PM: Moving platform:alarmtimer.0.auto to end of list [ T1] devices_kset: Moving wakeup1 to end of list [ T1] bus: 'platform': really_probe: bound device rtc-test.1 to driver rtc-test [ T1] Registering platform device 'rtc-test.2'. Parent at platform [ T1] device: 'rtc-test.2': device_add [ T1] bus: 'platform': add device rtc-test.2 [ T1] PM: Adding info for platform:rtc-test.2 [ T1] bus: 'platform': __driver_probe_device: matched device rtc-test.2 with driver rtc-test [ T1] bus: 'platform': really_probe: probing driver rtc-test with device rtc-test.2 [ T1] rtc-test rtc-test.2: no default pinctrl state [ T1] device: 'wakeup2': device_add [ T1] device: 'rtc2': device_add [ T1] PM: Adding info for No Bus:rtc2 [ T1] rtc-test rtc-test.2: char device (252:2) [ T1] rtc-test rtc-test.2: registered as rtc2 [ T1] driver: 'rtc-test': driver_bound: bound to device 'rtc-test.2' [ T1] devices_kset: Moving rtc-test.2 to end of list [ T1] PM: Moving platform:rtc-test.2 to end of list [ T1] devices_kset: Moving wakeup2 to end of list [ T1] devices_kset: Moving rtc2 to end of list [ T1] PM: Moving No Bus:rtc2 to end of list [ T1] bus: 'platform': really_probe: bound device rtc-test.2 to driver rtc-test [ T1] i2c_dev: i2c /dev entries driver [ T1] device class 'i2c-dev': registering [ T1] device: 'i2c-0': device_add [ T1] PM: Adding info for No Bus:i2c-0 [ T1] i2c_dev: adapter [2180000.i2c] registered as minor 0 [ T1] device: 'i2c-1': device_add [ T1] PM: Adding info for No Bus:i2c-1 [ T1] i2c_dev: adapter [21b0000.i2c] registered as minor 1 [ T1] bus: 'platform': add driver i2c-pca-platform [ T1] bus: 'platform': add driver i2c-mux-gpmux [ T1] bus: 'i2c': add driver pca954x [ T1] i2c-core: driver [pca954x] registered [ T1] bus: 'i2c': add driver i2c-slave-eeprom [ T1] i2c-core: driver [i2c-slave-eeprom] registered [ T1] bus: 'platform': add driver ptp_qoriq [ T1] bus: 'platform': __driver_probe_device: matched device 1afe000.ptp-timer with driver ptp_qoriq [ T1] bus: 'platform': really_probe: probing driver ptp_qoriq with device 1afe000.ptp-timer [ T1] ptp_qoriq 1afe000.ptp-timer: no pinctrl handle [ T1] ptp_qoriq: device tree node missing required elements, try automatic configuration [ T1] device: 'pps0': device_add [ T1] PM: Adding info for No Bus:pps0 [ T1] pps pps0: new PPS source ptp0 [ T1] device: 'ptp0': device_add [ T1] PM: Adding info for No Bus:ptp0 [ T1] driver: 'ptp_qoriq': driver_bound: bound to device '1afe000.ptp-timer' [ T1] devices_kset: Moving 1afe000.ptp-timer to end of list [ T1] PM: Moving platform:1afe000.ptp-timer to end of list [ T1] devices_kset: Moving ptp0 to end of list [ T1] PM: Moving No Bus:ptp0 to end of list [ T1] bus: 'platform': really_probe: bound device 1afe000.ptp-timer to driver ptp_qoriq [ T1] bus: 'platform': add driver xgene-reboot [ T1] bus: 'platform': add driver syscon-reboot [ T1] bus: 'platform': __driver_probe_device: matched device reboot with driver syscon-reboot [ T1] bus: 'platform': really_probe: probing driver syscon-reboot with device reboot [ T1] syscon-reboot reboot: no pinctrl handle [ T1] driver: 'syscon-reboot': driver_bound: bound to device 'reboot' [ T1] devices_kset: Moving reboot to end of list [ T1] PM: Moving platform:reboot to end of list [ T1] bus: 'platform': really_probe: bound device reboot to driver syscon-reboot [ T1] bus: 'platform': add driver syscon-reboot-mode [ T1] bus: 'i2c': add driver bq27xxx-battery [ T1] i2c-core: driver [bq27xxx-battery] registered [ T1] bus: 'i2c': add driver adt7462 [ T1] i2c-core: driver [adt7462] registered [ T1] bus: 'scmi_protocol': add driver scmi-hwmon [ T1] bus: 'platform': add driver scpi-hwmon [ T1] bus: 'i2c': add driver lm90 [ T1] i2c-core: driver [lm90] registered [ T1] bus: 'platform': add driver i.mx8mm_thermal [ T1] bus: 'platform': add driver qoriq_thermal [ T1] bus: 'amba': add driver sp805-wdt [ T1] bus: 'platform': add driver sbsa-gwdt [ T1] bus: 'platform': add driver dw_wdt [ T1] bus: 'platform': add driver imx2-wdt [ T1] bus: 'platform': __driver_probe_device: matched device 2ad0000.watchdog with driver imx2-wdt [ T1] bus: 'platform': really_probe: probing driver imx2-wdt with device 2ad0000.watchdog [ T1] imx2-wdt 2ad0000.watchdog: no pinctrl handle [ T1] device: 'watchdog': device_add [ T1] PM: Adding info for No Bus:watchdog [ T1] device: 'watchdog0': device_add [ T1] PM: Adding info for No Bus:watchdog0 [ T1] driver: 'imx2-wdt': driver_bound: bound to device '2ad0000.watchdog' [ T1] devices_kset: Moving 2ad0000.watchdog to end of list [ T1] PM: Moving platform:2ad0000.watchdog to end of list [ T1] devices_kset: Moving watchdog to end of list [ T1] PM: Moving No Bus:watchdog to end of list [ T1] devices_kset: Moving watchdog0 to end of list [ T1] PM: Moving No Bus:watchdog0 to end of list [ T1] bus: 'platform': really_probe: bound device 2ad0000.watchdog to driver imx2-wdt [ T1] bus: 'platform': add driver imx7ulp-wdt [ T1] bus: 'platform': add driver arm_smc_wdt [ T1] bus: 'platform': add driver synopsys-edac [ T1] bus: 'platform': add driver cpufreq-dt [ T1] bus: 'platform': add driver imx-cpufreq-dt [ T1] bus: 'scmi_protocol': add driver scmi-cpufreq [ T1] bus: 'platform': add driver scpi-cpufreq [ T1] bus: 'platform': add driver qoriq-cpufreq [ T1] bus: 'platform': __driver_probe_device: matched device qoriq-cpufreq with driver qoriq-cpufreq [ T1] bus: 'platform': really_probe: probing driver qoriq-cpufreq with device qoriq-cpufreq [ T1] qoriq-cpufreq qoriq-cpufreq: no default pinctrl state [ T1] device: 'cooling_device0': device_add [ T1] PM: Adding info for No Bus:cooling_device0 [ T1] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ T1] driver: 'qoriq-cpufreq': driver_bound: bound to device 'qoriq-cpufreq' [ T1] devices_kset: Moving qoriq-cpufreq to end of list [ T1] PM: Moving platform:qoriq-cpufreq to end of list [ T1] bus: 'platform': really_probe: bound device qoriq-cpufreq to driver qoriq-cpufreq [ T1] bus: 'platform': add driver psci-cpuidle [ T1] Registering platform device 'psci-cpuidle'. Parent at platform [ T1] device: 'psci-cpuidle': device_add [ T1] bus: 'platform': add device psci-cpuidle [ T1] PM: Adding info for platform:psci-cpuidle [ T1] bus: 'platform': __driver_probe_device: matched device psci-cpuidle with driver psci-cpuidle [ T1] bus: 'platform': really_probe: probing driver psci-cpuidle with device psci-cpuidle [ T1] psci-cpuidle psci-cpuidle: no default pinctrl state [ T1] driver: 'psci-cpuidle': driver_bound: bound to device 'psci-cpuidle' [ T1] devices_kset: Moving psci-cpuidle to end of list [ T1] PM: Moving platform:psci-cpuidle to end of list [ T1] bus: 'platform': really_probe: bound device psci-cpuidle to driver psci-cpuidle [ T1] bus: 'platform': add driver scpi_protocol [ T1] bus: 'platform': add driver scpi_power_domain [ T1] Registering platform device 'platform-framebuffer.0'. Parent at platform [ T1] device: 'platform-framebuffer.0': device_add [ T1] bus: 'platform': add device platform-framebuffer.0 [ T1] PM: Adding info for platform:platform-framebuffer.0 [ T1] bus: 'scmi_protocol': add driver scmi-power-domain [ T1] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ T1] bus: 'hid': registered [ T1] bus: 'hid': add driver hid-generic [ T1] bus: 'hid': add driver a4tech [ T1] bus: 'hid': add driver apple [ T1] bus: 'hid': add driver belkin [ T1] bus: 'hid': add driver cherry [ T1] bus: 'hid': add driver cypress [ T1] bus: 'hid': add driver ezkey [ T1] bus: 'hid': add driver itetech [ T1] bus: 'hid': add driver kensington [ T1] bus: 'hid': add driver microsoft [ T1] bus: 'hid': add driver monterey [ T1] bus: 'hid': add driver redragon [ T1] device: 'vhost-net': device_add [ T1] PM: Adding info for No Bus:vhost-net [ T1] bus: 'platform': add driver fsl-bman [ T1] bus: 'platform': __driver_probe_device: matched device 1890000.bman with driver fsl-bman [ T1] bus: 'platform': really_probe: probing driver fsl-bman with device 1890000.bman [ T1] fsl-bman 1890000.bman: no pinctrl handle [ T1] driver: 'fsl-bman': driver_bound: bound to device '1890000.bman' [ T1] devices_kset: Moving 1890000.bman to end of list [ T1] PM: Moving platform:1890000.bman to end of list [ T1] bus: 'platform': really_probe: bound device 1890000.bman to driver fsl-bman [ T1] bus: 'platform': add driver fsl-qman [ T1] bus: 'platform': __driver_probe_device: matched device 1880000.qman with driver fsl-qman [ T1] bus: 'platform': really_probe: probing driver fsl-qman with device 1880000.qman [ T1] fsl-qman 1880000.qman: no pinctrl handle [ T1] driver: 'fsl-qman': driver_bound: bound to device '1880000.qman' [ T1] devices_kset: Moving 1880000.qman to end of list [ T1] PM: Moving platform:1880000.qman to end of list [ T1] bus: 'platform': really_probe: bound device 1880000.qman to driver fsl-qman [ T1] Freescale USDPAA process driver [ T1] fsl-usdpaa: no region found [ T1] Freescale USDPAA process IRQ driver [ T1] device: 'fsl-usdpaa-irq': device_add [ T1] PM: Adding info for No Bus:fsl-usdpaa-irq [ T1] bus: 'fsl-mc': add driver dpaa2_evb [ T1] bus: 'platform': add driver pfe [ T1] bus: 'amba': add driver mhu [ T1] bus: 'amba': add driver mhu-doorbell [ T1] bus: 'platform': add driver platform-mhu [ T1] bus: 'rpmsg': add driver qcom_glink_ssr [ T1] device class 'extcon': registering [ T1] bus: 'platform': add driver extcon-usb-gpio [ T1] bus: 'platform': add driver imx8qxp_adc [ T1] bus: 'i2c': add driver st_lsm6dsx_i2c [ T1] i2c-core: driver [st_lsm6dsx_i2c] registered [ T1] bus: 'spi': add driver st_lsm6dsx_spi [ T1] bus: 'platform': add driver imx-ddr-pmu [ T1] bus: 'platform': add driver hisi_l3c_pmu [ T1] bus: 'platform': add driver hisi_hha_pmu [ T1] bus: 'platform': add driver hisi_ddrc_pmu [ T1] bus: 'platform': add driver hisi_sllc_pmu [ T1] bus: 'platform': add driver hisi_pa_pmu [ T1] bus: 'platform': add driver imx_ocotp [ T1] bus: 'platform': add driver optee [ T1] bus: 'platform': add driver mmio-mux [ T1] bus: 'platform': add driver interrupt-cnt [ T1] bus: 'platform': add driver mxc_hantro [ T1] bus: 'platform': add driver mxc_hantro_845 [ T1] bus: 'platform': add driver mxc_hantro_h1 [ T1] bus: 'platform': add driver mxc_hantro_vc8000e [ T1] NET: Registered PF_LLC protocol family [ T1] u32 classifier [ T1] input device check on [ T1] Actions configured [ T1] Initializing XFRM netlink socket [ T1] NET: Registered PF_INET6 protocol family [ T1] Segment Routing with IPv6 [ T1] In-situ OAM (IOAM) with IPv6 [ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ T1] device: 'sit0': device_add [ T1] PM: Adding info for No Bus:sit0 [ T1] NET: Registered PF_PACKET protocol family [ T1] NET: Registered PF_KEY protocol family [ T1] Bridge firewalling registered [ T1] 8021q: 802.1Q VLAN Support v1.8 [ T1] lib80211: common routines for IEEE802.11 drivers [ T1] lib80211_crypt: registered algorithm 'NULL' [ T1] lib80211_crypt: registered algorithm 'WEP' [ T1] lib80211_crypt: registered algorithm 'CCMP' [ T1] lib80211_crypt: registered algorithm 'TKIP' [ T1] tsn generic netlink module v1 init... [ T1] Key type dns_resolver registered [ T1] device: 'cpu_dma_latency': device_add [ T1] PM: Adding info for No Bus:cpu_dma_latency [ T1] Loading compiled-in X.509 certificates [ T1] device: 'btrfs-control': device_add [ T1] PM: Adding info for No Bus:btrfs-control [ T1] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ T1] bus: 'fsl-mc': add driver dpaa2-qdma [ T1] device class 'ubi': registering [ T1] device: 'ubi_ctrl': device_add [ T1] PM: Adding info for No Bus:ubi_ctrl [ T1] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ T1] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ T34] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ T34] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db [ T34] device: 'regulatory.db': device_add [ T34] PM: Adding info for No Bus:regulatory.db [ T1] Freeing unused kernel memory: 2304K [ T1] Run /init as init process [ T1] with arguments: [ T1] /init [ T1] with environment: [ T1] HOME=/ [ T1] TERM=linux [ T1] systemd[1]: System time before build time, advancing clock. [ T1] systemd[1]: systemd 250.5+ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid) [ T1] systemd[1]: Detected architecture arm64. Welcome to QorIQ SDK POC (Proof of Concept) 4.0.4 (kirkstone)! [ T1] systemd[1]: Hostname set to . [ T1] systemd[1]: Initializing machine ID from random generator. [ T179] systemd[179]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1. [ T1] systemd[1]: Queued start job for default target Multi-User System. [ T1] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ T1] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ T1] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ T1] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ T1] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ T1] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ T1] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ T1] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ T1] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ T1] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ T1] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ T1] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ T1] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ T1] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ T1] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ T1] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ T1] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ T1] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ T1] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ T1] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ T1] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ T1] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ T1] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ T1] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ T1] systemd[1]: Kernel Trace File System was skipped because of a failed condition check (ConditionPathExists=/sys/kernel/tracing). [ T1] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ T1] systemd[1]: Create List of Static Device Nodes was skipped because of a failed condition check (ConditionFileNotEmpty=/lib/modules/5.15.71+g95448dd0dc9b/modules.devname). [ T1] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ T1] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ T1] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ T1] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ T1] systemd[1]: File System Check on Root Device was skipped because of a failed condition check (ConditionPathIsReadWrite=!/). [ T1] systemd[1]: systemd-journald.service: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ T1] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ T1] systemd[1]: Starting Journal Service... Starting Journal Service... [ T1] systemd[1]: Load Kernel Modules was skipped because all trigger condition checks failed. [ T1] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network …ts from Kernel command line... [ T1] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ T1] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... [ T1] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ T1] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ T1] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted Huge Pages File System. [ T1] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ T1] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ T1] systemd[1]: Mounted Temporary Directory /tmp. [ OK ] Mounted Temporary Directory /tmp. [ T1] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. [ OK ] Finished Apply Kernel Variables. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... [ T198] systemd-journald[198]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create System Users. [ OK ] Finished Coldplug All udev Devices. Starting Create Static Device Nodes in /dev... Starting Wait for udev To …plete Device Initialization... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... Starting Rule-based Manage…for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. Starting Rebuild Dynamic Linker Cache... Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Rebuild Dynamic Linker Cache. [ OK ] Finished Create Volatile Files and Directories. Starting Rebuild Journal Catalog... Starting Network Time Synchronization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Finished Rebuild Journal Catalog. Starting Update is Completed... [ OK ] Finished Update is Completed. [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Started Hardware RNG Entropy Gatherer Daemon. [ OK ] Reached target System Initialization. [ OK ] Started Daily rotation of log files. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on dropbear.socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting D-Bus System Message Bus... [ T417] random: dbus-daemon: uninitialized urandom read (12 bytes read) [ OK ] Started A minimalistic net…Pv4, r[ T417] random: dbus-daemon: uninitialized urandom read (12 bytes read) disc and DHCPv6 [ T418] random: dhcpcd: uninitialized urandom read (112 bytes read) support. Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... Starting User Login Management... Starting GNU Zebra routing manager... [ OK ] Started D-Bus System Message Bus. [ OK ] Finished IPv6 Packet Filtering Framework. [ OK ] Finished IPv4 Packet Filtering Framework. [ OK ] Reached target Preparation for Network. Starting Network Configuration... [ OK ] Started GNU Zebra routing manager. Starting BGP routing daemon... [ T428] device: 'vcs6': device_add [ T428] PM: Adding info for No Bus:vcs6 [ T428] device: 'vcsu6': device_add [ T428] PM: Adding info for No Bus:vcsu6 [ T428] device: 'vcsa6': device_add [ T428] PM: Adding info for No Bus:vcsa6 Starting IS-IS routing daemon... [ T428] device: 'vcs2': device_add [ T428] PM: Adding info for No Bus:vcs2 [ T428] device: 'vcsu2': device_add [ T428] PM: Adding info for No Bus:vcsu2 [ T428] device: 'vcsa2': device_add [ T428] PM: Adding info for No Bus:vcsa2 Starting OSPF routing daemon for IPv6... [ T428] device: 'vcs3': device_add [ T428] PM: Adding info for No Bus:vcs3 [ T428] device: 'vcsu3': device_add [ T428] PM: Adding info for No Bus:vcsu3 [ T428] device: 'vcsa3': device_add [ T428] PM: Adding info for No Bus:vcsa3 Starting OSPF routing daemon... [ T428] device: 'vcs4': device_add [ T428] PM: Adding info for No Bus:vcs4 [ T428] device: 'vcsu4': device_add [ T428] PM: Adding info for No Bus:vcsu4 [ T428] device: 'vcsa4': device_add [ T428] PM: Adding info for No Bus:vcsa4 Starting RIP routing daemon... [ T428] device: 'vcs5': device_add [ T428] PM: Adding info for No Bus:vcs5 [ T428] device: 'vcsu5': device_add [ T428] PM: Adding info for No Bus:vcsu5 [ T428] device: 'vcsa5': device_add [ T428] PM: Adding info for No Bus:vcsa5 [ T433] adin_soft_reset Starting RIP routing daemon for IPv6... [ T433] adin_read_mmd [ OK [[ T433] adin_cl45_to_adin_reg 0m] Started [0;[ T433] adin_write_mmd 1;39mNetwork Con[ T433] adin_cl45_to_adin_reg figuration. [ OK ] Started BGP routing daemon. [ T433] adin_read_mmd [ T433] adin_cl45_to_adin_reg [ T433] adin_config_rgmii_mode [ T433] adin_read_mmd [ OK ] Started IS-IS routi[ T433] adin_cl45_to_adin_reg ng daemon. [ T433] ADIN1300_GE_RGMII_CFG_REG 0xe07 [ T433] adin_get_reg_value [ T433] adin_lookup_reg_value [ T433] ADIN1300_GE_RGMII_CFG_REG1 0xfc7 [ OK [[ T433] adin_get_reg_value 0m] Started [0;[ T433] adin_lookup_reg_value 1;39mOSPF routing daemon for IPv6. [ T433] ADIN1300_GE_RGMII_CFG_REG2 0xfff [ T433] ADIN1300_GE_RGMII_CFG_REG3 0xfff [ T433] adin_write_mmd [ T433] adin_cl45_to_adin_reg [ OK [[ T433] adin_read_mmd 0m] Started [0;[ T433] adin_cl45_to_adin_reg 1;39mOSPF routin[ T433] adin_config_init g daemon. [ T433] adin_set_downshift [ T433] adin_set_downshift adin_config_init [ T433] adin_set_edpd [ OK [[ T433] adin_set_edpd adin_config_init 0m] Started [0;[ T433] adin_phy_config_intr 1;39mRIP routing daemon. [ T433] adin_phy_ack_intr [ T433] adin_phy_config_intr [ T433] adin_phy_ack_intr [ OK [[ T107] adin_config_aneg 0m] Started [0;[ T107] adin_config_aneg ADIN1300_LINKING_EN 1;39mRIP routing[ T107] adin_config_mdix,0x1 daemon for IPv6. [ T107] adin_config_mdix,0x1 [ OK ] Started User Login Management. Starting Wait for Network to be Configured... Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Simple Network Ma…ent Protocol (SNMP) Daemon.... Starting Simple Network Ma…rotocol (SNMP) Trap Daemon.... Starting Permit User Sessions... [ OK ] Started Vsftpd ftp daemon. [ OK ] Started Xinetd A Powerful Replacement For Inetd. [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Serial Getty on ttyS1. [ OK ] Reached target Login Prompts. [ C3] random: crng init done [ OK ] Finished Load/Save Random Seed. [ OK ] Started Simple Network Man… Protocol (SNMP) Trap Daemon.. [ OK ] Started Simple Network Man…ement Protocol (SNMP) Daemon.. [ T36] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready QorIQ SDK POC (Proof of Concept) 4.0.4 ls1043ardb ttyS0 ls1043ardb login: root (automatic login) [ T37] audit: type=1006 audit(1651167753.996:2): pid=470 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1 [ T37] audit: type=1300 audit(1651167753.996:2): arch=c00000b7 syscall=64 success=yes exit=1 a0=8 a1=ffffe80cd6b0 a2=1 a3=ffffa0f9f020 items=0 ppid=1 pid=470 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="(systemd)" exe="/usr/lib/systemd/systemd" key=(null) [ T37] audit: type=1327 audit(1651167753.996:2): proctitle="(systemd)" killing and restarting snmpd service kill: usage: kill [-s sigspec | -n signum | -sigspec] pid | jobspec ... or kill -l [sigspec] echo 1 >/proc/sys/net/ipv4/ip_forward before ospfd after ospfd chmod: cannot access '/main': No such file or directory -sh: ./main: No such file or directory 78root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/# root@ls1043ardb:/#