• Autosar with Imx8/Imx6

    Hello Team,    I am planning to use the Imx8/Imx6 for integrating the Autosar. Could you kindly let me know on how to proceed with this. If i purchase the development board, will this come with the Autosar...
    Naveen B
    last modified by Naveen B
  • USB_HostEhciTaskFunction hangs in USB_HostEhciPortChange

    I'm using the MCUXpresso SDK USB version 2.2.1 with MCUXpresso SDK 2.6.2. Disconnect a device sometimes causes the host task (USB_HostEhciTaskFunction) to hang in USB_HostEhciPortChange. The break condition is never s...
    Jeffery Thompson
    last modified by Jeffery Thompson
  • iMX6 LVDS -24 bit mapping

    Hi, I am not clear about the 24 bit SPWG/PSWG/VESA  data mapping given in imx6 technical reference manual section 39.5.2. In below table 39.6, R6,G6,B6 represents LSB color bit  or 6th color bits ...
    Tamilarasan E
    last modified by Tamilarasan E
  • Can I burn eFuses for iMX8M Mini family using direct register access via JTAG?

    Hello,   I have a similar question as in https://community.nxp.com/thread/499677 .   We have programmed some of the eFuses (a.o. Boot cfg., MAC addresses) of various iMX6 devices with direct OCOTP_CTRL re...
    Stefan Konrad
    last modified by Stefan Konrad
  • Android P9.0.0_2.2.0-ga booting issue with i.MX6 Solo

    Hi community,   Has anyone ever booted in 6Solo mode with i.MX6DL SABER-SD? I am trying to boot android p9 as i.MX6Solo mode using i.MX6DL SABRE-SD board. But  after booting u-boot, kernel don't boot-up a...
    Mamoru Kanou
    last modified by Mamoru Kanou
  • fsl-image-validation-imx-1.0-r0 do_rootfs: Could not invoke dnf

    Hello experts,   I'm building the fsl-image-validation-imx image using fsl-yocto-L4.9.123_2.3.0_mx8mm under Ubuntu-16.04 :   $ repo init -u https://source.codeaurora.org/external/imx/imx-manifest -b imx-li...
    Khang Le Truong
    last modified by Khang Le Truong
  • How to enter SNVS mode by SW on imx7d?

    Hi!   According to "i.MX 7Dual Applications Processor Reference Manual, Rev. 1, 01/2018"  part 5.1.4.4 "Power Modes" there are two ways to enter "SNVS" mode  from "RUN" mode: ONOFF long press, or SW. ...
    Pawel Lenkow
    last modified by Pawel Lenkow
  • Command Line utility command for MFGtool2  to display the result and exit the command prompt.

     I am using the MCIMX6Y2DVM microcontroller in my testing board, I am programming this controller manually using MFGtool2.exe. I want to automate the programming for my project. I am using LabVIEW an industrial a...
    M Harishankaran
    last modified by M Harishankaran
  • Continuous noise issue during VOIP call

    Hello, I'm working on IMX8M Mini EVK with Android Pie (p9.0.0_2.3.0) OS. I have integrated CX9000 synaptics audio amplifier and CX20921 Dual MIC voice processor to the EVK.   There are two DMICs connected on ...
    Naman Thaker
    last modified by Naman Thaker
  • rm67191 Driver

    IMX8M平台 linux系统    rm67191的配置: static const struct display_timing rad_default_timing = { .pixelclock = { 66000000, 132000000, 132000000 }, .hactive = { 1080, 1080, 1080 }, .hfront_porch = { 20, 20, 20 }...
    tan yd
    last modified by tan yd
  • iMX8MM-EVK LPDDR4 not work

    Hi guys,   I'm used sample iMX8MM-EVK pcb from NXP to make a board, 100% like iMX8MM-EVK.   When I using MSCALE_DDR_TOOL version 310 to test LPDDR4. Calibration and street test OK. Result is attached bello...
    Kieu Dich
    last modified by Kieu Dich
  • IMX6DL PCIE can not read mem space

    We use imx6dl as  PCIE RC mode , the pmc-24dsi12 as EP side.  At x86 system , it diver OK. the same divers we used in imx6dl , but there have some problem: The PCIE can link up , and read config is ok , th...
    liguo li
    last modified by liguo li
  • I2S fsl_ssi_set_dai_fmt() has no effect

    Using an I2S driver without an audio codec initialization we were able to create a soundcard that can be used with alsa (both aplay/arecord are working, audio is transmitted, the sound is "off" though) but are unable ...
    Christian Fischer
    last modified by Christian Fischer
  • imx8mq_m4_TCM_hello_world.bin with Thud

    Release: Yocto-Thud ( kernel 4.19.35 ) Board: i.MX8MQ EVK Hello, I am checking Thud release and I would test M4 example, but I have a problem. When I try to load imx8mq_m4_TCM_hello_world.bin in u-boot, I get this me...
    Francesco Giusti
    last modified by Francesco Giusti
  • USB protection required when slave is powered, but master (i.MX8M) isn't

    Hello,   Our application is placed on a card which is mounted on a carrier PCB, out application is USB Master.   during certain situations the Carrier which contains the USB slave can be powered but the i....
    arnemaathuis
    last modified by arnemaathuis
  • What are type and pin assignment of JTAG connector (J4) on i.MX 8QuadXPlus MEK(MCIMX8QXP-CPU)?

    I'd like to connect Lauterbach JTAG debugger to the JTAG connector (J4) on i.MX 8QuadXPlus MEK(MCIMX8QXP-CPU) to debug CA35 software, and I'd like to know the connector type and pin assignment for JTAG signal.
    Takashi Sone
    last modified by Takashi Sone
  • IMX6UL:  imx-4.1.15-1.0.0_ga uboot-imx.git is not accessible

    I am trying to build imx6ulevk jethro (imx-4.1.15-1.0.0_ga) by following the below steps.   repo init -u https://source.codeaurora.org/external/imx/fsl-arm-yocto-bsp -b imx-4.1.15-1.0.0_ga repo sync DISTRO=fsl...
    Sivakumar Rajachidambaram
    last modified by Sivakumar Rajachidambaram
  • Bluetooth on imx7ulp eval board

    Hello,   I am working with imx7ulp eval board (L4.19.35_1.1.0 SW package) and facing issues in setting up bluetooth module.   As per document "iMX Linux User guide" Section 10 "Connectivity", I am trying t...
    jai ganesh sridharan
    last modified by jai ganesh sridharan
  • Exploring audio over ethernet

    Dear all,   We have supercomputer which is running on windows and an Android device : I.MX8QM running with Android 9 automotive. We need to live stream audio from supercomputer to Android device (imx8qm) an...
    Amit Kulkarni
    last modified by Amit Kulkarni
  • How fast is iMX8 Secure Boot?

    Does anyone know how fast the iMX8 AHAB Secure Boot stages are? Obviously, it depends on the sizes of the signed blobs. Are there specs on how fast the SECO can hash the code? Verify the signature? Thank you
    Stuart Rubin
    created by Stuart Rubin